On Mon, Feb 03, 2025 at 04:05:34PM +0100, Julian Huhn wrote:
On Mon, Feb 03, 2025 at 02:33:59PM +0000, Stuart Henderson wrote:
On 2025-02-03, Julian Huhn <jul...@huhn.dev> wrote:
Moin!
I'm trying to connect to an Internet exchange with a bnxt(4) interface, but I
only get 10GbaseSR as the media type, not 10GbaseLR as expected. When I try to
set the media type manually, it fails with an "Invalid argument". In fact,
10GbaseLR isn't listed as a supported media type for the interface. Is this
correct? Is SR the only supported mode on this type of network card?
You can't switch between SR and LR in software, it's dependent on
the transceiver.
Ok, but the transceiver is LR as far as I can see, so it was
misidentified by bnxt(4), right?
Is it working OK anyway? (i.e. is this just a cosmetic issue?)
Unfortunately, I cannot establish connectivity with the interface. However,
both sides claim that the interfaces are active.
Perhaps the transceiver is to blame. On Linux (Debian), a similar behavior can
be observed. So this is not specific to OpenBSD. I shut down the VM and looked
at the active, passed-through interface on the host, which also showed that only
SR is supported. However, Linux advertises all expected media types on the
inactive interface.
--Huhn
On Linux:
# ethtool enp1s0f0np0
Settings for enp1s0f0np0:
Supported ports: [ FIBRE ]
Supported link modes: 25000baseSR/Full
10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: RS BASER
Advertised link modes: 25000baseSR/Full
10000baseSR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Lanes: 1
Duplex: Full
Auto-negotiation: on
Port: FIBRE
PHYAD: 1
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00002081 (8321)
drv tx_err hw
Link detected: no
# ethtool enp1s0f1np1
Settings for enp1s0f1np1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
10000baseKX4/Full
10000baseKR/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: RS BASER
Advertised link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
10000baseKX4/Full
10000baseKR/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: FIBRE
PHYAD: 1
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00002081 (8321)
drv tx_err hw
Link detected: no
On OpenBSD:
# ifconfig bnxt0 media
bnxt0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 6c:92:cf:12:94:e0
index 1 priority 0 llprio 3
media: Ethernet autoselect (10GbaseSR full-duplex)
status: active
supported media:
media 1000baseSX
media 10GbaseSR
media 25GbaseSR
media autoselect
# ifconfig bnxt1 media
bnxt1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 6c:92:cf:12:94:e1
index 2 priority 0 llprio 3
media: Ethernet autoselect
status: no carrier
supported media:
media 1000baseT
media 10GSFP+Cu
media autoselect
