Somebody claiming to be Dave Vandervies wrote:
> After upgrading to 7.4, my pine64-lts box failed to boot bsd.mp on
> two out of two tries, with an identical panic message both times:
> (see below for full (u-boot + kernel + ddb) boot log of the panic
> and dmesg from bsd.sp which does boot)
Ahh, here's some interesting additional information: If I turn off
the external USB disk I have attached to this box before booting,
and turn it back on once the boot finishes, bsd.mp also boots without
panicking.
Here's the dmesg from a succesful bsd.mp boot:
--------
OpenBSD 7.4 (GENERIC.MP) #2273: Tue Oct 10 09:45:06 MDT 2023
[email protected]:/usr/src/sys/arch/arm64/compile/GENERIC.MP
real mem = 2027782144 (1933MB)
avail mem = 1928839168 (1839MB)
random: good seed from bootblocks
mainbus0 at root: Pine64 LTS
psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
efi0 at mainbus0: UEFI 2.8
efi0: Das U-Boot rev 0x20211000
smbios0 at efi0: SMBIOS 3.0
smbios0: vendor U-Boot version "2021.10" date 10/01/2021
smbios0: Unknown Unknown Product
cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu0: 512KB 64b/line 16-way L2 cache
cpu0: CRC32,SHA2,SHA1,AES+PMULL,ASID16
cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4
cpu1: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu1: 512KB 64b/line 16-way L2 cache
cpu1: CRC32,SHA2,SHA1,AES+PMULL,ASID16
cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4
cpu2: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu2: 512KB 64b/line 16-way L2 cache
cpu2: CRC32,SHA2,SHA1,AES+PMULL,ASID16
cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4
cpu3: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu3: 512KB 64b/line 16-way L2 cache
cpu3: CRC32,SHA2,SHA1,AES+PMULL,ASID16
apm0 at mainbus0
"display-engine" at mainbus0 not configured
"osc24M_clk" at mainbus0 not configured
"osc32k_clk" at mainbus0 not configured
"pmu" at mainbus0 not configured
simpleaudio0 at mainbus0
agtimer0 at mainbus0: 24000 kHz
simplebus0 at mainbus0: "soc"
sxisyscon0 at simplebus0
sxisid0 at simplebus0
sxiccmu0 at simplebus0
sxipio0 at simplebus0: 103 pins
ampintc0 at simplebus0 nirq 224, ncpu 4 ipi: 0, 1, 2: "interrupt-controller"
sxirtc0 at simplebus0
sxiccmu1 at simplebus0
sxipio1 at simplebus0: 13 pins
sxirsb0 at simplebus0
axppmic0 at sxirsb0 addr 0x3a3: AXP803
"bus" at simplebus0 not configured
"dma-controller" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
"video-codec" at simplebus0 not configured
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
sximmc1 at simplebus0
sdmmc1 at sximmc1: 8-bit, sd high-speed, mmc high-speed, dma
"crypto" at simplebus0 not configured
"mailbox" at simplebus0 not configured
"usb" at simplebus0 not configured
"phy" at simplebus0 not configured
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
ohci0 at simplebus0: version 1.0
ehci1 at simplebus0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
ohci1 at simplebus0: version 1.0
"timer" at simplebus0 not configured
sxidog0 at simplebus0
"dai" at simplebus0 not configured
"codec" at simplebus0 not configured
sxitemp0 at simplebus0
com0 at simplebus0: dw16550
com0: console
"spi" at simplebus0 not configured
dwxe0 at simplebus0: address 02:bc:b8:a1:ec:e9
rgephy0 at dwxe0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
"gpu" at simplebus0 not configured
"dram-controller" at simplebus0 not configured
"deinterlace" at simplebus0 not configured
"hdmi" at simplebus0 not configured
"hdmi-phy" at simplebus0 not configured
sxirintc0 at simplebus0
"codec-analog" at simplebus0 not configured
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
gpio7 at sxipio0: 32 pins
gpio8 at sxipio1: 32 pins
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00
addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00
addr 1
"opp_table0" at mainbus0 not configured
"hdmi-connector" at mainbus0 not configured
"vcc1v8" at mainbus0 not configured
gpioleds0 at mainbus0: no LEDs
simplefb0 at mainbus0: 1920x1080, 32bpp
wsdisplay0 at simplefb0 mux 1
wsdisplay0: screen 0-5 added (std, vt100 emulation)
sdmmc0: can't enable card
scsibus0 at sdmmc1: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, NCard, 0000> removable
sd0: 59000MB, 512 bytes/sector, 120832000 sectors
uhub4 at uhub1 port 1 configuration 1 interface 0 "VIA Labs, Inc. USB2.0 Hub"
rev 2.10/2.14 addr 2
uhidev0 at uhub4 port 2 configuration 1 interface 0 "Unicomp Endura Pro
Keyboard" rev 1.10/43.34 addr 3
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes
wskbd0 at ukbd0 mux 1
wskbd0: connecting to wsdisplay0
uhidev1 at uhub4 port 2 configuration 1 interface 1 "Unicomp Endura Pro
Keyboard" rev 1.10/43.34 addr 3
uhidev1: iclass 3/1, 3 report ids
ums0 at uhidev1 reportid 1: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
ucc0 at uhidev1 reportid 2: 573 usages, 20 keys, array
wskbd1 at ucc0 mux 1
wskbd1: connecting to wsdisplay0
uhid0 at uhidev1 reportid 3: input=1, output=0, feature=0
uhidev2 at uhub4 port 3 configuration 1 interface 0 "Logitech USB Laser Mouse"
rev 2.00/56.01 addr 4
uhidev2: iclass 3/1
ums1 at uhidev2: 8 buttons, Z and W dir
wsmouse1 at ums1 mux 0
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on sd0a (823130ad660d9ca0.a) swap on sd0b dump on sd0b
umass0 at uhub4 port 1 configuration 1 interface 0 "ASMT ASMT105x" rev
2.10/1.00 addr 5
umass0: using SCSI over Bulk-Only
scsibus3 at umass0: 2 targets, initiator 0
sd1 at scsibus3 targ 1 lun 0: <WDC WD40, EFAX-68JH4N1, 0>
serial.174c55aa234567890126
sd1: 3815447MB, 512 bytes/sector, 7814037168 sectors
--------
> --------
> panic: uvm_fault: fault on non-pageable map (0xffffff80012dbd48,
> 0xffffff8007f7
> d000)
> Stopped at panic+0x164: cmp w21, #0x0
> TID PID UID PRFLAGS PFLAGS CPU COMMAND
> 459227 91515 0 0x14000 0x200 3 update
> *165810 5998 0 0x14000 0x200 2K cleaner
> 8700 14349 0 0x14000 0x200 1 reaper
> 0 0 0 0x10000 0x200 0 swapper
> db_enter() at panic+0x160
> panic() at uvm_fault_check+0x5e0
> uvm_fault_check() at uvm_fault+0xd4
> uvm_fault() at kdata_abort+0xd0
> kdata_abort() at handle_el1h_sync+0x6c
> handle_el1h_sync() at comopen+0x578
> comopen() at proc_trampoline+0x4
> https://www.openbsd.org/ddb.html describes the minimum info required in bug
> reports. Insufficient info makes it difficult to find and fix bugs.
> ddb{2}> trace
> db_enter() at panic+0x160
> panic() at uvm_fault_check+0x5e0
> uvm_fault_check() at uvm_fault+0xd4
> uvm_fault() at kdata_abort+0xd0
> kdata_abort() at handle_el1h_sync+0x6c
> handle_el1h_sync() at comopen+0x578
> comopen() at proc_trampoline+0x4
> ddb{2}> machine ddbcpu 0
>
> --------
>
> ddb doesn't come back after I say 'machine ddbcpu 0', it just hung
> there until I ran out of patience and power cycled (identical
> behavior in both tries), which makes it impossible to collect traces
> from the other CPUs as recommended by ddb.html. The only differences
> between the panic messages are the TID and PID values in the ps
> listing; the values in the panic message itself and the backtrace
> match exactly.
>
> The upgrade kernel, bsd.rd, and bsd.sp all boot without problems.
>
> What other information is worth collecting here? Anything I should
> try to see if there's a way to fix it without a kernel patch?
>
>
> Thanks,
> dave
>
>
> serial console log of the full boot + panic with bsd.mp:
> --------
> U-Boot SPL 2021.10 (Apr 09 2022 - 20:52:48 -0600)
> DRAM: 2048 MiB
> Trying to boot from MMC2
> NOTICE: BL31: v2.5(debug):2.5
> NOTICE: BL31: Built : 16:26:47, Apr 9 2022
> NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689)
> NOTICE: BL31: Found U-Boot DTB at 0x4097d10, model: Pine64 LTS
> INFO: ARM GICv2 driver initialized
> INFO: Configuring SPC Controller
> INFO: PMIC: Probing AXP803 on RSB
> INFO: PMIC: dcdc1 voltage: 3.300V
> INFO: PMIC: dcdc5 voltage: 1.200V
> INFO: PMIC: dcdc6 voltage: 1.100V
> INFO: PMIC: dldo1 voltage: 3.300V
> INFO: PMIC: dldo2 voltage: 3.300V
> INFO: PMIC: dldo4 voltage: 3.300V
> INFO: PMIC: fldo1 voltage: 1.200V
> INFO: PMIC: Enabling DC SW
> INFO: BL31: Platform setup done
> INFO: BL31: Initializing runtime services
> INFO: BL31: cortex_a53: CPU workaround for 843419 was applied
> INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
> INFO: BL31: cortex_a53: CPU workaround for 1530924 was applied
> INFO: PSCI: Suspend is unavailable
> INFO: BL31: Preparing for EL3 exit to normal world
> INFO: Entry point address = 0x4a000000
> INFO: SPSR = 0x3c9
>
>
> U-Boot 2021.10 (Apr 09 2022 - 20:52:48 -0600) Allwinner Technology
>
> CPU: Allwinner A64 (SUN50I)
> Model: Pine64 LTS
> DRAM: 2 GiB
> MMC: mmc@1c0f000: 0, mmc@1c11000: 1
> Loading Environment from FAT... Unable to read "uboot.env" from mmc1:1... In:
> serial
> Out: vidconsole
> Err: vidconsole
> Net: phy interface8
> eth0: ethernet@1c30000
> starting USB...
> Bus usb@1c1a000: USB EHCI 1.00
> Bus usb@1c1a400: USB OHCI 1.0
> Bus usb@1c1b000: USB EHCI 1.00
> Bus usb@1c1b400: USB OHCI 1.0
> scanning bus usb@1c1a000 for devices... 1 USB Device(s) found
> scanning bus usb@1c1a400 for devices... 1 USB Device(s) found
> scanning bus usb@1c1b000 for devices... 5 USB Device(s) found
> scanning bus usb@1c1b400 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
> Hit any key to stop autoboot: 2 1 0
> switch to partitions #0, OK
> mmc1(part 0) is current device
> Scanning mmc 1:1...
> 28618 bytes read in 3 ms (9.1 MiB/s)
> 7[r[999;999H[6n8Card did not respond to voltage select! : -110
> Scanning disk [email protected]...
> Disk [email protected] not ready
> Scanning disk [email protected]...
> Scanning disk usb_mass_storage.lun0...
> Disk usb_mass_storage.lun0 not ready
> Found 3 disks
> No EFI system partition
> BootOrder not defined
> EFI boot manager: Cannot load any image
> Found EFI removable media binary efi/boot/bootaa64.efi
> 219050 bytes read in 7 ms (29.8 MiB/s)
> Booting /efi\boot\bootaa64.efi
> disks: sd0*
> >> OpenBSD/arm64 BOOTAA64 1.18
> |/-\|/-\|/boot>
> -\|/-\|/-\booting sd0a:/bsd:
> |/-\|/10659816-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/+2522120-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/+296760-\|/-\|/-\|/-\|/-\+849688|
>
> [789483/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/+91+1219896-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\+731575|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|]=0x13b5490
> [ using 2741824 bytes of bsd ELF symbol table ]
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2023 OpenBSD. All rights reserved. https://www.OpenBSD.org
>
> OpenBSD 7.4 (GENERIC.MP) #2273: Tue Oct 10 09:45:06 MDT 2023
> [email protected]:/usr/src/sys/arch/arm64/compile/GENERIC.MP
> real mem = 2027782144 (1933MB)
> avail mem = 1928839168 (1839MB)
> random: good seed from bootblocks
> mainbus0 at root: Pine64 LTS
> psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
> efi0 at mainbus0: UEFI 2.8
> efi0: Das U-Boot rev 0x20211000
> smbios0 at efi0: SMBIOS 3.0
> smbios0: vendor U-Boot version "2021.10" date 10/01/2021
> smbios0: Unknown Unknown Product
> cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
> cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu0: 512KB 64b/line 16-way L2 cache
> cpu0: CRC32,SHA2,SHA1,AES+PMULL,ASID16
> cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4
> cpu1: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu1: 512KB 64b/line 16-way L2 cache
> cpu1: CRC32,SHA2,SHA1,AES+PMULL,ASID16
> cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4
> cpu2: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu2: 512KB 64b/line 16-way L2 cache
> cpu2: CRC32,SHA2,SHA1,AES+PMULL,ASID16
> cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4
> cpu3: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu3: 512KB 64b/line 16-way L2 cache
> cpu3: CRC32,SHA2,SHA1,AES+PMULL,ASID16
> apm0 at mainbus0
> "display-engine" at mainbus0 not configured
> "osc24M_clk" at mainbus0 not configured
> "osc32k_clk" at mainbus0 not configured
> "pmu" at mainbus0 not configured
> simpleaudio0 at mainbus0
> agtimer0 at mainbus0: 24000 kHz
> simplebus0 at mainbus0: "soc"
> sxisyscon0 at simplebus0
> sxisid0 at simplebus0
> sxiccmu0 at simplebus0
> sxipio0 at simplebus0: 103 pins
> ampintc0 at simplebus0 nirq 224, ncpu 4 ipi: 0, 1, 2: "interrupt-controller"
> sxirtc0 at simplebus0
> sxiccmu1 at simplebus0
> sxipio1 at simplebus0: 13 pins
> sxirsb0 at simplebus0
> axppmic0 at sxirsb0 addr 0x3a3: AXP803
> "bus" at simplebus0 not configured
> "dma-controller" at simplebus0 not configured
> "lcd-controller" at simplebus0 not configured
> "lcd-controller" at simplebus0 not configured
> "video-codec" at simplebus0 not configured
> sximmc0 at simplebus0
> sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
> sximmc1 at simplebus0
> sdmmc1 at sximmc1: 8-bit, sd high-speed, mmc high-speed, dma
> "crypto" at simplebus0 not configured
> "mailbox" at simplebus0 not configured
> "usb" at simplebus0 not configured
> "phy" at simplebus0 not configured
> ehci0 at simplebus0
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
> 2.00/1.00 addr 1
> ohci0 at simplebus0: version 1.0
> ehci1 at simplebus0
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev
> 2.00/1.00 addr 1
> ohci1 at simplebus0: version 1.0
> "timer" at simplebus0 not configured
> sxidog0 at simplebus0
> "dai" at simplebus0 not configured
> "codec" at simplebus0 not configured
> sxitemp0 at simplebus0
> com0 at simplebus0: dw16550
> com0: console
> "spi" at simplebus0 not configured
> dwxe0 at simplebus0: address 02:bc:b8:a1:ec:e9
> rgephy0 at dwxe0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
> "gpu" at simplebus0 not configured
> "dram-controller" at simplebus0 not configured
> "deinterlace" at simplebus0 not configured
> "hdmi" at simplebus0 not configured
> "hdmi-phy" at simplebus0 not configured
> sxirintc0 at simplebus0
> "codec-analog" at simplebus0 not configured
> gpio0 at sxipio0: 32 pins
> gpio1 at sxipio0: 32 pins
> gpio2 at sxipio0: 32 pins
> gpio3 at sxipio0: 32 pins
> gpio4 at sxipio0: 32 pins
> gpio5 at sxipio0: 32 pins
> gpio6 at sxipio0: 32 pins
> gpio7 at sxipio0: 32 pins
> gpio8 at sxipio1: 32 pins
> usb2 at ohci0: USB revision 1.0
> uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev
> 1.00/1.00 addr 1
> usb3 at ohci1: USB revision 1.0
> uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev
> 1.00/1.00 addr 1
> "opp_table0" at mainbus0 not configured
> "hdmi-connector" at mainbus0 not configured
> "vcc1v8" at mainbus0 not configured
> gpioleds0 at mainbus0: no LEDs
> simplefb0 at mainbus0: 1920x1080, 32bpp
> wsdisplay0 at simplefb0 mux 1
> wsdisplay0: screen 0-5 added (std, vt100 emulation)
> sdmmc0: can't enable card
> scsibus0 at sdmmc1: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <SD/MMC, NCard, 0000> removable
> sd0: 59000MB, 512 bytes/sector, 120832000 sectors
> uhub4 at uhub1 port 1 configuration 1 interface 0 "VIA Labs, Inc. USB2.0 Hub"
> rev 2.10/2.14 addr 2
> umass0 at uhub4 port 1 configuration 1 interface 0 "ASMT ASMT105x" rev
> 2.10/1.00 addr 3
> umass0: using SCSI over Bulk-Only
> scsibus1 at umass0: 2 targets, initiator 0
> sd1 at scsibus1 targ 1 lun 0: <WDC WD40, EFAX-68JH4N1, 0>
> serial.174c55aa234567890126
> sd1: 3815447MB, 512 bytes/sector, 7814037168 sectors
> uhidev0 at uhub4 port 2 configuration 1 interface 0 "Unicomp Endura Pro
> Keyboard" rev 1.10/43.34 addr 4
> uhidev0: iclass 3/1
> ukbd0 at uhidev0: 8 variable keys, 6 key codes
> wskbd0 at ukbd0 mux 1
> wskbd0: connecting to wsdisplay0
> uhidev1 at uhub4 port 2 configuration 1 interface 1 "Unicomp Endura Pro
> Keyboard" rev 1.10/43.34 addr 4
> uhidev1: iclass 3/1, 3 report ids
> ums0 at uhidev1 reportid 1: 3 buttons, Z dir
> wsmouse0 at ums0 mux 0
> ucc0 at uhidev1 reportid 2: 573 usages, 20 keys, array
> wskbd1 at ucc0 mux 1
> wskbd1: connecting to wsdisplay0
> uhid0 at uhidev1 reportid 3: input=1, output=0, feature=0
> uhidev2 at uhub4 port 3 configuration 1 interface 0 "Logitech USB Laser
> Mouse" rev 2.00/56.01 addr 5
> uhidev2: iclass 3/1
> ums1 at uhidev2: 8 buttons, Z and W dir
> wsmouse1 at ums1 mux 0
> vscsi0 at root
> scsibus2 at vscsi0: 256 targets
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> root on sd0a (823130ad660d9ca0.a) swap on sd0b dump on sd0b
> panic: uvm_fault: fault on non-pageable map (0xffffff80012dbd48,
> 0xffffff8007f7
> d000)
> Stopped at panic+0x164: cmp w21, #0x0
> TID PID UID PRFLAGS PFLAGS CPU COMMAND
> 459227 91515 0 0x14000 0x200 3 update
> *165810 5998 0 0x14000 0x200 2K cleaner
> 8700 14349 0 0x14000 0x200 1 reaper
> 0 0 0 0x10000 0x200 0 swapper
> db_enter() at panic+0x160
> panic() at uvm_fault_check+0x5e0
> uvm_fault_check() at uvm_fault+0xd4
> uvm_fault() at kdata_abort+0xd0
> kdata_abort() at handle_el1h_sync+0x6c
> handle_el1h_sync() at comopen+0x578
> comopen() at proc_trampoline+0x4
> https://www.openbsd.org/ddb.html describes the minimum info required in bug
> reports. Insufficient info makes it difficult to find and fix bugs.
> ddb{2}> trace
> db_enter() at panic+0x160
> panic() at uvm_fault_check+0x5e0
> uvm_fault_check() at uvm_fault+0xd4
> uvm_fault() at kdata_abort+0xd0
> kdata_abort() at handle_el1h_sync+0x6c
> handle_el1h_sync() at comopen+0x578
> comopen() at proc_trampoline+0x4
> ddb{2}> machine ddbcpu 0
>
>
>
> bsd.sp dmesg:
> --------
> OpenBSD 7.4 (GENERIC) #321: Tue Oct 10 09:15:09 MDT 2023
> [email protected]:/usr/src/sys/arch/arm64/compile/GENERIC
> real mem = 2027782144 (1933MB)
> avail mem = 1928851456 (1839MB)
> random: boothowto does not indicate good seed
> mainbus0 at root: Pine64 LTS
> psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
> efi0 at mainbus0: UEFI 2.8
> efi0: Das U-Boot rev 0x20211000
> smbios0 at efi0: SMBIOS 3.0
> smbios0: vendor U-Boot version "2021.10" date 10/01/2021
> smbios0: Unknown Unknown Product
> cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
> cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu0: 512KB 64b/line 16-way L2 cache
> cpu0: CRC32,SHA2,SHA1,AES+PMULL,ASID16
> apm0 at mainbus0
> "display-engine" at mainbus0 not configured
> "osc24M_clk" at mainbus0 not configured
> "osc32k_clk" at mainbus0 not configured
> "pmu" at mainbus0 not configured
> simpleaudio0 at mainbus0
> agtimer0 at mainbus0: 24000 kHz
> simplebus0 at mainbus0: "soc"
> sxisyscon0 at simplebus0
> sxisid0 at simplebus0
> sxiccmu0 at simplebus0
> sxipio0 at simplebus0: 103 pins
> ampintc0 at simplebus0 nirq 224, ncpu 4: "interrupt-controller"
> sxirtc0 at simplebus0
> sxiccmu1 at simplebus0
> sxipio1 at simplebus0: 13 pins
> sxirsb0 at simplebus0
> axppmic0 at sxirsb0 addr 0x3a3: AXP803
> "bus" at simplebus0 not configured
> "dma-controller" at simplebus0 not configured
> "lcd-controller" at simplebus0 not configured
> "lcd-controller" at simplebus0 not configured
> "video-codec" at simplebus0 not configured
> sximmc0 at simplebus0
> sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
> sximmc1 at simplebus0
> sdmmc1 at sximmc1: 8-bit, sd high-speed, mmc high-speed, dma
> "crypto" at simplebus0 not configured
> "mailbox" at simplebus0 not configured
> "usb" at simplebus0 not configured
> "phy" at simplebus0 not configured
> ehci0 at simplebus0
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
> 2.00/1.00 addr 1
> ohci0 at simplebus0: version 1.0
> ehci1 at simplebus0
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev
> 2.00/1.00 addr 1
> ohci1 at simplebus0: version 1.0
> "timer" at simplebus0 not configured
> sxidog0 at simplebus0
> "dai" at simplebus0 not configured
> "codec" at simplebus0 not configured
> sxitemp0 at simplebus0
> com0 at simplebus0: dw16550
> com0: console
> "spi" at simplebus0 not configured
> dwxe0 at simplebus0: address 02:bc:b8:a1:ec:e9
> rgephy0 at dwxe0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
> "gpu" at simplebus0 not configured
> "dram-controller" at simplebus0 not configured
> "deinterlace" at simplebus0 not configured
> "hdmi" at simplebus0 not configured
> "hdmi-phy" at simplebus0 not configured
> sxirintc0 at simplebus0
> "codec-analog" at simplebus0 not configured
> gpio0 at sxipio0: 32 pins
> gpio1 at sxipio0: 32 pins
> gpio2 at sxipio0: 32 pins
> gpio3 at sxipio0: 32 pins
> gpio4 at sxipio0: 32 pins
> gpio5 at sxipio0: 32 pins
> gpio6 at sxipio0: 32 pins
> gpio7 at sxipio0: 32 pins
> gpio8 at sxipio1: 32 pins
> usb2 at ohci0: USB revision 1.0
> uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev
> 1.00/1.00 addr 1
> usb3 at ohci1: USB revision 1.0
> uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev
> 1.00/1.00 addr 1
> "opp_table0" at mainbus0 not configured
> "hdmi-connector" at mainbus0 not configured
> "vcc1v8" at mainbus0 not configured
> gpioleds0 at mainbus0: no LEDs
> simplefb0 at mainbus0: 1920x1080, 32bpp
> wsdisplay0 at simplefb0 mux 1
> wsdisplay0: screen 0-5 added (std, vt100 emulation)
> sdmmc0: can't enable card
> scsibus0 at sdmmc1: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <SD/MMC, NCard, 0000> removable
> sd0: 59000MB, 512 bytes/sector, 120832000 sectors
> uhub4 at uhub1 port 1 configuration 1 interface 0 "VIA Labs, Inc. USB2.0 Hub"
> rev 2.10/2.14 addr 2
> umass0 at uhub4 port 1 configuration 1 interface 0 "ASMT ASMT105x" rev
> 2.10/1.00 addr 3
> umass0: using SCSI over Bulk-Only
> scsibus1 at umass0: 2 targets, initiator 0
> sd1 at scsibus1 targ 1 lun 0: <WDC WD40, EFAX-68JH4N1, 0>
> serial.174c55aa234567890126
> sd1: 3815447MB, 512 bytes/sector, 7814037168 sectors
> uhidev0 at uhub4 port 2 configuration 1 interface 0 "Unicomp Endura Pro
> Keyboard" rev 1.10/43.34 addr 4
> uhidev0: iclass 3/1
> ukbd0 at uhidev0: 8 variable keys, 6 key codes
> wskbd0 at ukbd0 mux 1
> wskbd0: connecting to wsdisplay0
> uhidev1 at uhub4 port 2 configuration 1 interface 1 "Unicomp Endura Pro
> Keyboard" rev 1.10/43.34 addr 4
> uhidev1: iclass 3/1, 3 report ids
> ums0 at uhidev1 reportid 1: 3 buttons, Z dir
> wsmouse0 at ums0 mux 0
> ucc0 at uhidev1 reportid 2: 573 usages, 20 keys, array
> wskbd1 at ucc0 mux 1
> wskbd1: connecting to wsdisplay0
> uhid0 at uhidev1 reportid 3: input=1, output=0, feature=0
> uhidev2 at uhub4 port 3 configuration 1 interface 0 "Logitech USB Laser
> Mouse" rev 2.00/56.01 addr 5
> uhidev2: iclass 3/1
> ums1 at uhidev2: 8 buttons, Z and W dir
> wsmouse1 at ums1 mux 0
> vscsi0 at root
> scsibus2 at vscsi0: 256 targets
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> root on sd0a (823130ad660d9ca0.a) swap on sd0b dump on sd0b
> --------
>
> --
> Dave Vandervies
> [email protected]
>
> Plan your future! Make God laugh!
>
--
Dave Vandervies
[email protected]
Plan your future! Make God laugh!
