Hi all,
This is my first time writing to this list, so forgive me if I miss
something. This is also my first time using OpenBSD.
I'm running OpenBSD 7.3 on a Thinkpad T460, which has two batteries. One
internal battery, and one removable battery. The expected behavior (e.g.
on Linux) is that the removable battery discharges first until it
reaches 5%, then the internal battery begins to discharge.
On OpenBSD when I run apm it shows only the charge of the "current"
battery. This means the removable battery if it is plugged in, or the
internal battery if the removable battery is not plugged in. This also
means that the system attempts to hibernate/cleanly shut down when the
charge of the removable battery becomes very low.
Another symptom of this is that the % charge showed by apm goes *up*
when I unplug the removable battery.
Is there a way to check the percent charge of each battery individually?
I would like apm to show me something like "80% 30%" instead of the
current "30%".
Both batteries are detected by acpibat and show up in sysctl:
hw.sensors.acpibat0.volt0=11.10 VDC (voltage)
hw.sensors.acpibat0.volt1=10.92 VDC (current voltage)
hw.sensors.acpibat0.power0=0.00 W (rate)
hw.sensors.acpibat0.watthour0=7.95 Wh (last full capacity)
hw.sensors.acpibat0.watthour1=0.40 Wh (warning capacity)
hw.sensors.acpibat0.watthour2=0.20 Wh (low capacity)
hw.sensors.acpibat0.watthour3=0.37 Wh (remaining capacity), WARNING
hw.sensors.acpibat0.watthour4=20.54 Wh (design capacity)
hw.sensors.acpibat0.raw0=0 (battery idle), OK
hw.sensors.acpibat1.volt0=10.80 VDC (voltage)
hw.sensors.acpibat1.volt1=11.57 VDC (current voltage)
hw.sensors.acpibat1.power0=23.74 W (rate)
hw.sensors.acpibat1.watthour0=unknown (last full capacity), UNKNOWN
hw.sensors.acpibat1.watthour1=0.00 Wh (warning capacity)
hw.sensors.acpibat1.watthour2=0.00 Wh (low capacity)
hw.sensors.acpibat1.watthour3=0.67 Wh (remaining capacity), OK
hw.sensors.acpibat1.watthour4=unknown (design capacity), UNKNOWN
hw.sensors.acpibat1.raw0=unknown (battery unknown), UNKNOWN
My dmesg is:
OpenBSD 7.3 (GENERIC.MP) #1125: Sat Mar 25 10:36:29 MDT 2023
dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 16533991424 (15768MB)
avail mem = 16013496320 (15271MB)
random: good seed from bootblocks
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0xd7056000 (65 entries)
bios0: vendor LENOVO version "R06ET71W (1.45 )" date 02/21/2022
bios0: LENOVO 20FMS3YP00
acpi0 at bios0: ACPI 5.0
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP TCPA SSDT UEFI SSDT SSDT ECDT HPET APIC MCFG
SSDT SSDT DBGP DBG2 BOOT BATB SLIC SSDT SSDT MSDM DMAR ASF! FPDT UEFI
acpi0: wakeup devices LID_(S4) SLPB(S3) IGBE(S4) EXP8(S4) XHCI(S3)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpiec0 at acpi0
acpihpet0 at acpi0: 23999999 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Core(TM) i5-6300U CPU @ 2.40GHz, 1065.21 MHz, 06-4e-03
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SGX,BMI1,HLE,AVX2,SMEP,BMI2,ERMS,INVPCID,RTM,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SRBDS_CTRL,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu0: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 256KB
64b/line 4-way L2 cache, 3MB 64b/line 12-way L3 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
cpu0: apic clock running at 24MHz
cpu0: mwait min=64, max=64, C-substates=0.2.1.2.4.1.1.1, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Core(TM) i5-6300U CPU @ 2.40GHz, 906.26 MHz, 06-4e-03
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SGX,BMI1,HLE,AVX2,SMEP,BMI2,ERMS,INVPCID,RTM,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SRBDS_CTRL,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu1: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 256KB
64b/line 4-way L2 cache, 3MB 64b/line 12-way L3 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 1 (application processor)
cpu2: Intel(R) Core(TM) i5-6300U CPU @ 2.40GHz, 897.91 MHz, 06-4e-03
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SGX,BMI1,HLE,AVX2,SMEP,BMI2,ERMS,INVPCID,RTM,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SRBDS_CTRL,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu2: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 256KB
64b/line 4-way L2 cache, 3MB 64b/line 12-way L3 cache
cpu2: smt 1, core 0, package 0
cpu3 at mainbus0: apid 3 (application processor)
cpu3: Intel(R) Core(TM) i5-6300U CPU @ 2.40GHz, 897.91 MHz, 06-4e-03
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SGX,BMI1,HLE,AVX2,SMEP,BMI2,ERMS,INVPCID,RTM,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SRBDS_CTRL,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu3: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 256KB
64b/line 4-way L2 cache, 3MB 64b/line 12-way L3 cache
cpu3: smt 1, core 1, package 0
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 120 pins
acpimcfg0 at acpi0
acpimcfg0: addr 0xf8000000, bus 0-63
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus -1 (PEG0)
acpiprt2 at acpi0: bus -1 (PEG1)
acpiprt3 at acpi0: bus -1 (PEG2)
acpiprt4 at acpi0: bus 2 (EXP1)
acpiprt5 at acpi0: bus 4 (EXP3)
acpiprt6 at acpi0: bus -1 (EXP4)
acpiprt7 at acpi0: bus -1 (EXP5)
acpiprt8 at acpi0: bus -1 (EXP8)
acpiprt9 at acpi0: bus -1 (RP09)
acpibtn0 at acpi0: LID_
acpibtn1 at acpi0: SLPB
acpipci0 at acpi0 PCI0: 0x00000000 0x00000011 0x00000001
acpicmos0 at acpi0
acpibat0 at acpi0: BAT0 model "45N1111" serial 12545 type LiP oem "SONY"
acpibat1 at acpi0: BAT1
acpiac0 at acpi0: AC unit online
acpithinkpad0 at acpi0: version 1.0
"PNP0C14" at acpi0 not configured
"PNP0C14" at acpi0 not configured
"PNP0C14" at acpi0 not configured
tpm0 at acpi0 TPM_ 1.2 (TIS) addr 0xfed40000/0x5000, device 0x001b15d1
rev 0x10
acpicpu0 at acpi0: C3(200@1034 mwait.1@0x60), C2(200@151 mwait.1@0x33),
C1(1000@1 mwait.1), PSS
acpicpu1 at acpi0: C3(200@1034 mwait.1@0x60), C2(200@151 mwait.1@0x33),
C1(1000@1 mwait.1), PSS
acpicpu2 at acpi0: C3(200@1034 mwait.1@0x60), C2(200@151 mwait.1@0x33),
C1(1000@1 mwait.1), PSS
acpicpu3 at acpi0: C3(200@1034 mwait.1@0x60), C2(200@151 mwait.1@0x33),
C1(1000@1 mwait.1), PSS
acpipwrres0 at acpi0: PUBS, resource for XHCI
acpipwrres1 at acpi0: PG00, resource for PEG0
acpipwrres2 at acpi0: PG01, resource for PEG1
acpipwrres3 at acpi0: PG02, resource for PEG2
acpipwrres4 at acpi0: WRST
acpipwrres5 at acpi0: WRST
acpitz0 at acpi0: critical temperature is 128 degC
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD1F
cpu0: using VERW MDS workaround (except on vmm entry)
cpu0: Enhanced SpeedStep 1065 MHz: speeds: 2401, 2400, 2300, 2200, 2000,
1900, 1700, 1600, 1400, 1300, 1100, 1000, 800, 700, 500, 400 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Core 6G Host" rev 0x08
inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics 520" rev 0x07
drm0 at inteldrm0
inteldrm0: msi, SKYLAKE, gen 9
xhci0 at pci0 dev 20 function 0 "Intel 100 Series xHCI" rev 0x21: msi,
xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
3.00/1.00 addr 1
pchtemp0 at pci0 dev 20 function 2 "Intel 100 Series Thermal" rev 0x21
"Intel 100 Series MEI" rev 0x21 at pci0 dev 22 function 0 not configured
puc0 at pci0 dev 22 function 3 "Intel 100 Series KT" rev 0x21: ports: 16 com
com4 at puc0 port 0 apic 2 int 19: ns16550a, 16 byte fifo
ahci0 at pci0 dev 23 function 0 "Intel 100 Series AHCI" rev 0x21: msi,
AHCI 1.3.1
ahci0: port 1: 6.0Gb/s
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 1 lun 0: <ATA, Samsung SSD 840, EXT0>
naa.50025388a01c09d6
sd0: 238475MB, 512 bytes/sector, 488397168 sectors, thin
ppb0 at pci0 dev 28 function 0 "Intel 100 Series PCIE" rev 0xf1: msi
pci1 at ppb0 bus 2
rtsx0 at pci1 dev 0 function 0 "Realtek RTS522A Card Reader" rev 0x01: msi
sdmmc0 at rtsx0: 4-bit, dma
ppb1 at pci0 dev 28 function 2 "Intel 100 Series PCIE" rev 0xf1: msi
pci2 at ppb1 bus 4
iwm0 at pci2 dev 0 function 0 "Intel AC 8260" rev 0x3a, msi
pcib0 at pci0 dev 31 function 0 "Intel 100 Series LPC" rev 0x21
"Intel 100 Series PMC" rev 0x21 at pci0 dev 31 function 2 not configured
azalia0 at pci0 dev 31 function 3 "Intel 100 Series HD Audio" rev 0x21: msi
azalia0: codecs: Realtek ALC293, Intel/0x2809, using Realtek ALC293
audio0 at azalia0
ichiic0 at pci0 dev 31 function 4 "Intel 100 Series SMBus" rev 0x21:
apic 2 int 16
iic0 at ichiic0
em0 at pci0 dev 31 function 6 "Intel I219-LM" rev 0x21: msi, address
c8:5b:76:c7:ff:99
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard
pms0 at pckbc0 (aux slot)
wsmouse0 at pms0 mux 0
wsmouse1 at pms0 mux 0
pms0: Synaptics clickpad, firmware 8.2, 0x1e2b1 0x943300 0x2fed40
0xf006a3 0x12e800
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
vmm0 at mainbus0: VMX/EPT
ugen0 at uhub0 port 7 "Intel Bluetooth" rev 2.00/0.01 addr 2
ugen1 at uhub0 port 9 "Validity Sensors VFS5011 Fingerprint Reader" rev
1.10/0.78 addr 3
uvideo0 at uhub0 port 10 configuration 1 interface 0 "Chicony
Electronics Co.,Ltd. Integrated Camera" rev 2.00/0.29 addr 4
video0 at uvideo0
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
sd1 at scsibus3 targ 1 lun 0: <OPENBSD, SR CRYPTO, 006>
sd1: 238474MB, 512 bytes/sector, 488396576 sectors
root on sd1a (fa0153fa9add268b.a) swap on sd1b dump on sd1b
drm:pid0:intel_ddi_sanitize_encoder_pll_mapping *NOTICE* [drm]
[ENCODER:102:DDI B/PHY B] is disabled/in DSI mode with an ungated DDI
clock, gate it
drm:pid0:intel_ddi_sanitize_encoder_pll_mapping *NOTICE* [drm]
[ENCODER:116:DDI C/PHY C] is disabled/in DSI mode with an ungated DDI
clock, gate it
inteldrm0: 1920x1080, 32bpp
wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation), using wskbd0
wsdisplay0: screen 1-5 added (std, vt100 emulation)
iwm0: hw rev 0x200, fw ver 36.ca7b901d.0, address 34:f3:9a:fc:5a:49
Thanks in advance for any help.
