> > 4. Did some Raspberry Pi's come with a micro sd slot or something???
> > There's mention of using a small SD card as well as having a USB
> > device for OpenBSD... this doesn't seem to apply to Pi 4 B as there
> > are only USB ports...
The 4B does take a micro SD card, I am running off it now.
Jan
OpenBSD 7.0-current (GENERIC) #1458: Tue Jan 25 11:33:09 MST 2022
dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC
real mem = 8419872768 (8029MB)
avail mem = 8128622592 (7752MB)
random: good seed from bootblocks
mainbus0 at root: Raspberry Pi 4 Model B Rev 1.4
cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu0: 1024KB 64b/line 16-way L2 cache
cpu0: CRC32,ASID16
apm0 at mainbus0
efi0 at mainbus0: UEFI 2.8
efi0: Das U-Boot rev 0x20211000
"system" at mainbus0 not configured
"axi" at mainbus0 not configured
simplebus0 at mainbus0: "soc"
bcmclock0 at simplebus0
bcmmbox0 at simplebus0
bcmgpio0 at simplebus0
bcmaux0 at simplebus0
ampintc0 at simplebus0 nirq 256, ncpu 4: "interrupt-controller"
bcmtmon0 at simplebus0
bcmdmac0 at simplebus0: DMA0 DMA2 DMA4 DMA5 DMA6 DMA7 DMA8 DMA9
"timer" at simplebus0 not configured
pluart0 at simplebus0: console
"local_intc" at simplebus0 not configured
bcmdog0 at simplebus0
bcmirng0 at simplebus0
"firmware" at simplebus0 not configured
"power" at simplebus0 not configured
"mailbox" at simplebus0 not configured
sdhc0 at simplebus0
sdhc0: SDHC 3.0, 250 MHz base clock
sdmmc0 at sdhc0: 4-bit, sd high-speed, mmc high-speed
"gpiomem" at simplebus0 not configured
"fb" at simplebus0 not configured
"vcsm" at simplebus0 not configured
"clocks" at mainbus0 not configured
"phy" at mainbus0 not configured
"clk-27M" at mainbus0 not configured
"clk-108M" at mainbus0 not configured
simplebus1 at mainbus0: "emmc2bus"
sdhc1 at simplebus1
sdhc1: SDHC 3.0, 100 MHz base clock
sdmmc1 at sdhc1: 8-bit, sd high-speed, mmc high-speed, ddr52, dma
"arm-pmu" at mainbus0 not configured
agtimer0 at mainbus0: 54000 kHz
simplebus2 at mainbus0: "scb"
bcmpcie0 at simplebus2
pci0 at bcmpcie0
ppb0 at pci0 dev 0 function 0 "Broadcom BCM2711" rev 0x10
pci1 at ppb0 bus 1
xhci0 at pci1 dev 0 function 0 "VIA VL805 xHCI" rev 0x01: intx, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "VIA xHCI root hub" rev 3.00/1.00
addr 1
bse0 at simplebus2: address dc:a6:32:e0:50:d3
brgphy0 at bse0 phy 1: BCM54210E 10/100/1000baseT PHY, rev. 2
"dma" at simplebus2 not configured
"hevc-decoder" at simplebus2 not configured
"rpivid-local-intc" at simplebus2 not configured
"h264-decoder" at simplebus2 not configured
"vp9-decoder" at simplebus2 not configured
gpioleds0 at mainbus0: "led0", "led1"
"sd_io_1v8_reg" at mainbus0 not configured
"sd_vcc_reg" at mainbus0 not configured
"fixedregulator_3v3" at mainbus0 not configured
"fixedregulator_5v0" at mainbus0 not configured
simplebus3 at mainbus0: "v3dbus"
"bootloader" at mainbus0 not configured
scsibus0 at sdmmc1: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SU32G, 0080> removable
sd0: 30436MB, 512 bytes/sector, 62333952 sectors
uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub" rev
2.10/4.21 addr 2
bwfm0 at sdmmc0 function 1
manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 2 not configured
manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 3 not configured
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on sd0a (d1a7e0233ab9545d.a) swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!
gpio0 at bcmgpio0: 58 pins
bwfm0: address dc:a6:32:e0:50:d4
