On Wed, Apr 08, 2020 at 07:03:29PM +0200, Sigi Rudzio wrote:
> Am Mi., 8. Apr. 2020 um 08:37 Uhr schrieb Otto Moerbeek <o...@drijf.net>:
> >
> > On Wed, Apr 08, 2020 at 01:11:29AM +0200, Sigi Rudzio wrote:
> >
> > > Hello misc@,
> > >
> > > while testing the FFS2 patches by otto@ I noticed that I was unable
> > > to install -current on my silver Blade 2500.
> > >
> > > tar fails while unpacking the sets, although the files are ok, if I rename
> > > base67.tgz to base66.tgz to fool the 6.6 installer I can install 6.7-beta,
> > > although it fails/panics with a lot of "Illegal instruction" errors on the
> > > first boot.
> > >
> > > otto@ already told me that this might be fallout from the recent clang
> > > changes.
> >
> > Well, I sais it *could be*, but you did not show my the actual errors
> > in that email. The errorsbelow indicate a harware issue, i.e. bad
> > disk.
> >
> > -Otto
>
> Sorry, I should have been clearer.
>
> I tried another disk from my working V240 and got the same errors.
>
> Installing on an IDE hard disk works and the system is working fine,
> even writing large files to the SCSI disk is fine, but I can make it panic
> with tar.
> So I guess this is some kind of SCSI bus hardware issue that 6.6 doesn't
> trigger and some change between 6.6 and 6.7-beta does trigger it.
>
> Sorry for the noise and thanks for the help!
Hmm, you might be onto something. I have seen similar issues on a
Blade 150 but blamed it on hardware. Sadly I do not thave easy access
to the machine atm.
-Otto
>
> Regards
>
> S. Rudzio
>
> >
> > >
> > > 6.6 works fine.
> > >
> > > The failures are a bit random, it doesn't panic every time, sometimes
> > > while installing 6.7-beta tar fails and I get to try again a few times
> > > before
> > > I give up/it panics.
> > >
> > > I hope this information helps.
> > >
> > > Regards,
> > >
> > > S. Rudzio
> > >
> > > output from
> > > -6.7-beta bsd.rd failing
> > > -6.6 bsd.rd
> > > -6.6 bsd.mp
> > > -6.7-beta bsd.mp failing/panicing (installed with 6.6 bsd.rd)
> > > following:
> > >
> > > latest bsd.rd (the previous two snapshots also failed, but I didn't save
> > > any
> > > logs):
> > > Booting /pci@1c,600000/network@3/bsd.rd
> > > 4671584@0x1000000+6048@0x1474860+3248464@0x1c00000+945840@0x1f19150
> > > symbols @ 0xfec68440 175+356136+219433 start=0x1000000
> > > console is /pci@1e,600000/isa@7/serial@0,3f8
> > > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > > The Regents of the University of California. All rights
> > > reserved.
> > > Copyright (c) 1995-2020 OpenBSD. All rights reserved.
> > > https://www.OpenBSD.org
> > >
> > > OpenBSD 6.7-beta (RAMDISK) #259: Mon Apr 6 19:13:12 MDT 2020
> > > dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/RAMDISK
> > > real mem = 2147483648 (2048MB)
> > > avail mem = 2098044928 (2000MB)
> > > mainbus0 at root: Sun Blade 2500 (Silver)
> > > "SUNW,UltraSPARC-IIIi" at mainbus0 not configured
> > > cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > > cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > > external (64 b/l)
> > > "memory-controller" at mainbus0 not configured
> > > "memory-controller" at mainbus0 not configured
> > > schizo0 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0
> > > schizo0: dvma map c0000000-dfffffff
> > > pci0 at schizo0
> > > bge0 at pci0 dev 3 function 0 "Broadcom BCM5703" rev 0x00,
> > > BCM5702/5703 A2 (0x1002)bge0: nvram lock timed out
> > > : ivec 0x71c, address 00:03:ba:f2:ee:53
> > > brgphy0 at bge0 phy 1: BCM5703 10/100/1000baseT PHY, rev. 2
> > > "ppm" at mainbus0 not configured
> > > schizo1 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0
> > > schizo1: dvma map c0000000-dfffffff
> > > pci1 at schizo1
> > > mpi0 at pci1 dev 4 function 0 "Symbios Logic 53c1030" rev 0x07: ivec
> > > 0x769
> > > mpi0: 0, firmware 1.3.11.1
> > > scsibus0 at mpi0: 16 targets, initiator 7
> > > sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > > sd0: 140009MB, 512 bytes/sector, 286739329 sectors
> > > mpi0: target 0 Sync at 160MHz width 16bit offset 63 QAS 1 DT 1 IU 1
> > > mpi1 at pci1 dev 4 function 1 "Symbios Logic 53c1030" rev 0x07: ivec
> > > 0x768
> > > mpi1: 0, firmware 1.3.11.1
> > > scsibus1 at mpi1: 16 targets, initiator 7
> > > schizo2 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 1
> > > schizo2: dvma map c0000000-dfffffff
> > > pci2 at schizo2
> > > ebus0 at pci2 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
> > > "flashprom" at ebus0 addr 0-fffff not configured
> > > rtc0 at ebus0 addr 70-71: m5823
> > > "i2c" at ebus0 addr 320-321 ivec 0x2e not configured
> > > "power" at ebus0 addr 800-82f ivec 0x20 not configured
> > > com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo
> > > com0: console
> > > com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo
> > > "dma" at ebus0 addr 0-ffff not configured
> > > "Acer Labs M7101 Power" rev 0x00 at pci2 dev 6 function 0 not
> > > configured
> > > "Acer Labs M5451 Audio" rev 0x02 at pci2 dev 8 function 0 not
> > > configured
> > > ohci0 at pci2 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > > 0x7a7, version 1.0, legacy support
> > > ohci1 at pci2 dev 11 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > > 0x7a6, version 1.0, legacy support
> > > pciide0 at pci2 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4:
> > > DMA, channel 0 configured to native-PCI, channel 1 configured to
> > > native-PCI
> > > pciide0: using ivec 0x798 for native-PCI interrupt
> > > pciide0: channel 0 disabled (no drives)
> > > atapiscsi0 at pciide0 channel 1 drive 0
> > > scsibus2 at atapiscsi0: 2 targets
> > > cd0 at scsibus2 targ 0 lun 0: <TSSTcorp, CDW/DVD TS-H492C, SI00>
> > > removable
> > > cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> > > radeonfb0 at pci2 dev 2 function 0 "ATI Radeon VE" rev 0x00
> > > radeonfb0: SUNW,375-3181, 1152x900
> > > wsdisplay0 at radeonfb0
> > > wsdisplay0: screen 0 added (std, sun emulation)
> > > ppb0 at pci2 dev 4 function 0 "TI PCI2250" rev 0x02
> > > pci3 at ppb0 bus 1
> > > ohci2 at pci3 dev 8 function 0 "NEC USB" rev 0x43: ivec 0x794, version
> > > 1.0
> > > ohci3 at pci3 dev 8 function 1 "NEC USB" rev 0x43: ivec 0x795, version
> > > 1.0
> > > ehci0 at pci3 dev 8 function 2 "NEC USB" rev 0x04: ivec 0x796
> > > usb0 at ehci0: USB revision 2.0
> > > uhub0 at usb0 configuration 1 interface 0 "NEC EHCI root hub" rev
> > > 2.00/1.00 addr 1
> > > "TI TSB43AB23 FireWire" rev 0x00 at pci3 dev 11 function 0 not configured
> > > usb1 at ohci2: USB revision 1.0
> > > uhub1 at usb1 configuration 1 interface 0 "NEC OHCI root hub" rev
> > > 1.00/1.00 addr 1
> > > usb2 at ohci3: USB revision 1.0
> > > uhub2 at usb2 configuration 1 interface 0 "NEC OHCI root hub" rev
> > > 1.00/1.00 addr 1
> > > usb3 at ohci0: USB revision 1.0
> > > uhub3 at usb3 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > > rev 1.00/1.00 addr 1
> > > usb4 at ohci1: USB revision 1.0
> > > uhub4 at usb4 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > > rev 1.00/1.00 addr 1
> > > "ppm" at mainbus0 not configured
> > > schizo3 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0
> > > schizo3: dvma map c0000000-dfffffff
> > > pci4 at schizo3
> > > "i2c" at mainbus0 not configured
> > > softraid0 at root
> > > scsibus3 at softraid0: 256 targets
> > > bootpath: /pci@1c,600000/network@3,0
> > > root on rd0a swap on rd0b dump on rd0b
> > > erase ^?, werase ^W, kill ^U, intr ^C, status ^T
> > >
> > > Welcome to the OpenBSD/sparc64 6.7 installation program.
> > > Starting non-interactive mode in 5 seconds...
> > > (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
> > > At any prompt except password prompts you can escape to a shell by
> > > typing '!'. Default answers are shown in []'s and are selected by
> > > pressing RETURN. You can exit this program at any time by pressing
> > > Control-C, but this can leave your system in an inconsistent state.
> > >
> > > Terminal type? [sun] xterm
> > > System hostname? (short form, e.g. 'foo') XXX
> > >
> > > Available network interfaces are: bge0 vlan0.
> > > Which network interface do you wish to configure? (or 'done') [bge0]
> > > IPv4 address for bge0? (or 'dhcp' or 'none') [dhcp]
> > > bge0: 192.168.2.131 lease accepted from 192.168.2.1
> > > (fe:e1:ba:d2:bf:d6)
> > > IPv6 address for bge0? (or 'autoconf' or 'none') [none] autoconf
> > > Available network interfaces are: bge0 vlan0.
> > > Which network interface do you wish to configure? (or 'done') [done]
> > > Using DNS domainname XXX
> > > Using DNS nameservers at 192.168.3.1
> > >
> > > Password for root account? (will not echo)
> > > Password for root account? (again)
> > > Start sshd(8) by default? [yes]
> > > Do you want the X Window System to be started by xenodm(1)? [no]
> > > Setup a user? (enter a lower-case loginname, or 'no') [no]
> > > Since no user was setup, root logins via sshd(8) might be useful.
> > > WARNING: root is targeted by password guessing attacks, pubkeys are
> > > safer.
> > > Allow root ssh login? (yes, no, prohibit-password) [no]
> > > What timezone are you in? ('?' for list) [XXX]
> > >
> > > Available disks are: sd0.
> > > Which disk is the root disk? ('?' for details) [sd0]
> > > The auto-allocated layout for sd0 is:
> > > # size offset fstype [fsize bsize cpg]
> > > a: 1.0G 0 4.2BSD 2048 16384 1 # /
> > > b: 2.3G 2116608 swap
> > > c: 136.7G 0 unused
> > > d: 4.0G 6838272 4.2BSD 2048 16384 1 #
> > > /tmp
> > > e: 8.0G 15243648 4.2BSD 2048 16384 1 #
> > > /var
> > > f: 6.0G 32034048 4.2BSD 2048 16384 1 #
> > > /usr
> > > g: 1.0G 44631936 4.2BSD 2048 16384 1 #
> > > /usr/X11R6
> > > h: 19.9G 46748544 4.2BSD 2048 16384 1 #
> > > /usr/local
> > > i: 2.0G 88551552 4.2BSD 2048 16384 1 #
> > > /usr/src
> > > j: 6.0G 92764416 4.2BSD 2048 16384 1 #
> > > /usr/obj
> > > k: 86.5G 105362304 4.2BSD 2048 16384 1 #
> > > /home
> > > Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a]
> > > /dev/rsd0a: 1033.5MB in 2116608 sectors of 512 bytes
> > > 6 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > > /dev/rsd0k: 88563.0MB in 181377024 sectors of 512 bytes
> > > 438 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > > /dev/rsd0d: 4104.2MB in 8405376 sectors of 512 bytes
> > > 21 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > > /dev/rsd0f: 6151.3MB in 12597888 sectors of 512 bytes
> > > 31 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > > /dev/rsd0g: 1033.5MB in 2116608 sectors of 512 bytes
> > > 6 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > > /dev/rsd0h: 20411.6MB in 41803008 sectors of 512 bytes
> > > 101 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > > /dev/rsd0j: 6151.3MB in 12597888 sectors of 512 bytes
> > > 31 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > > /dev/rsd0i: 2057.1MB in 4212864 sectors of 512 bytes
> > > 11 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > > /dev/rsd0e: 8198.4MB in 16790400 sectors of 512 bytes
> > > 41 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > > /dev/sd0a (a8bb856211488659.a) on /mnt type ffs (rw, asynchronous, local)
> > > /dev/sd0k (a8bb856211488659.k) on /mnt/home type ffs (rw,
> > > asynchronous, local, nodev, nosuid)
> > > /dev/sd0d (a8bb856211488659.d) on /mnt/tmp type ffs (rw, asynchronous,
> > > local, nodev, nosuid)
> > > /dev/sd0f (a8bb856211488659.f) on /mnt/usr type ffs (rw, asynchronous,
> > > local, nodev)
> > > /dev/sd0g (a8bb856211488659.g) on /mnt/usr/X11R6 type ffs (rw,
> > > asynchronous, local, nodev)
> > > /dev/sd0h (a8bb856211488659.h) on /mnt/usr/local type ffs (rw,
> > > asynchronous, local, nodev)
> > > /dev/sd0j (a8bb856211488659.j) on /mnt/usr/obj type ffs (rw,
> > > asynchronous, local, nodev, nosuid)
> > > /dev/sd0i (a8bb856211488659.i) on /mnt/usr/src type ffs (rw,
> > > asynchronous, local, nodev, nosuid)
> > > /dev/sd0e (a8bb856211488659.e) on /mnt/var type ffs (rw, asynchronous,
> > > local, nodev, nosuid)
> > >
> > > Let's install the sets!
> > > Location of sets? (cd0 disk http or 'done') [http]
> > > HTTP proxy URL? (e.g. 'http://proxy:8080', or 'none') [none]
> > > HTTP Server? (hostname, list#, 'done' or '?') [ftp.rudzio.net]
> > > Server directory? [pub/OpenBSD/snapshots/sparc64]
> > >
> > > Select sets by entering a set name, a file name pattern or 'all'.
> > > De-select
> > > sets by prepending a '-', e.g.: '-game*'. Selected sets are labelled
> > > '[X]'.
> > > [X] bsd [X] base67.tgz [X] game67.tgz [X] xfont67.tgz
> > > [X] bsd.mp [X] comp67.tgz [X] xbase67.tgz [X] xserv67.tgz
> > > [X] bsd.rd [X] man67.tgz [X] xshare67.tgz
> > > Set name(s)? (or 'abort' or 'done') [done]
> > > Get/Verify SHA256.sig 100% |**************************| 1885
> > > 00:00
> > > Signature Verified
> > > Get/Verify bsd 100% |**************************| 12483 KB
> > > 00:01
> > > Get/Verify bsd.mp 100% |**************************| 12541 KB
> > > 00:01
> > > Get/Verify bsd.rd 100% |**************************| 8560 KB
> > > 00:00
> > > Get/Verify base67.tgz 100% |**************************| 169 MB
> > > 00:15
> > > Get/Verify comp67.tgz 100% |**************************| 71992 KB
> > > 00:06
> > > Get/Verify man67.tgz 100% |**************************| 7455 KB
> > > 00:00
> > > Get/Verify game67.tgz 100% |**************************| 2866 KB
> > > 00:00
> > > Get/Verify xbase67.tgz 100% |**************************| 18753 KB
> > > 00:01
> > > Get/Verify xshare67.tgz 100% |**************************| 4500 KB
> > > 00:00
> > > Get/Verify xfont67.tgz 100% |**************************| 39345 KB
> > > 00:03
> > > Get/Verify xserv67.tgz 100% |**************************| 12537 KB
> > > 00:01
> > > Installing bsd 100% |**************************| 12483 KB
> > > 00:00
> > > Installing bsd.mp 100% |**************************| 12541 KB
> > > 00:00
> > > Installing bsd.rd 100% |**************************| 8560 KB
> > > 00:00
> > > Installing base67.tgz 66% |***************** | 113 MB
> > > 00:17 ETAftp: Reading from file: Input/output error
> > > gzip: stdin: Input/output error
> > > tar: End of archive volume 1 reached
> > > /mnt/usr: bad dir ino 622362 at offset 0: mangled entry
> > > panic: bad dir
> > > syncing disks...95 95 54 done
> > > Frame pointer is at 0x4002f23c8e1
> > > Call traceback:
> > > 12fdec4(1fab000, 80206910, 4002f23d190, 0, 12cacbc, 1f1d000,
> > > 4002f23c9b1) fp = 4002f23c9b1
> > > 110cbf4(100, 1c01000, 1, 100, 1, 0, 4002f23ca61) fp = 4002f23ca61
> > > 1117ab8(100, 1f1d000, 1, 4002f23d458, 1f1e295, ffffffffffffffff,
> > > 4002f23cb11) fp = 4002f23cb11
> > > 11c8d28(141d000, 4002f23d458, 100, 13aa000, 13b83ff, 4002f23d461,
> > > 4002f23cbd1) fp = 4002f23cbd1
> > > 11c827c(13b8000, 0, 13b83ff, 400047b1400, 40003b19330, 400047d5800,
> > > 4002f23cc81) fp = 4002f23cc81
> > > 1140a18(40003a1a750, 200, 40003a21e20, 4002f23db48, 0, 13b8000,
> > > 4002f23cdc1) fp = 4002f23cdc1
> > > 1137eb4(40003a1a750, 11c7f70, 1, 0, 2000, 0, 4002f23ce91) fp = 4002f23ce91
> > > 11376c4(4002f23dac8, 40003a1a750, 4002f23db48, 2001, 4002f23daf8,
> > > c044, 4002f23cf81) fp = 4002f23cf81
> > > 1141b74(4002f23dac8, 40004296020, 4002f23db08, 0, 400044ef800, 400,
> > > 4002f23d0a1) fp = 4002f23d0a1
> > > 113d3f4(4002f23dac8, 20001, 44, 40004333f20, 0, 16, 4002f23d1f1) fp =
> > > 4002f23d1f1
> > > 113d254(40004296020, 4002f23dac8, 20001, 20000, 1, 0, 4002f23d461) fp
> > > = 4002f23d461
> > > 1308818(40004296020, 4002f23ddd8, 4002f23ddc8, 141e892, 11d891c, 2e,
> > > 4002f23d511) fp = 4002f23d511
> > > 1011b64(4002f23ded0, 405, 40004296020, 113d23c, 50, 5, 4002f23d621) fp
> > > = 4002f23d621
> > > 23e800(2fde7bb40, 20000, 0, 0, cc, 0, fffffffffffd3211) fp =
> > > fffffffffffd3211
> > >
> > > dump to dev 5,1 not possible
> > > rebooting
> > >
> > >
> > > dmesg bsd.rd 6.6:
> > >
> > > Booting /pci@1c,600000/network@3/bsd.rd
> > > 4190432@0x1000000+3872@0x13ff0e0+3252800@0x1c00000+941504@0x1f1a240
> > > symbols @ 0xfec4e400 165+363672+220023 start=0x1000000
> > > console is /pci@1e,600000/isa@7/serial@0,3f8
> > > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > > The Regents of the University of California. All rights reserved.
> > > Copyright (c) 1995-2019 OpenBSD. All rights reserved.
> > > https://www.OpenBSD.org
> > >
> > > OpenBSD 6.6 (RAMDISK) #84: Sat Oct 12 10:42:12 MDT 2019
> > > dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/RAMDISK
> > > real mem = 2147483648 (2048MB)
> > > avail mem = 2098487296 (2001MB)
> > > mainbus0 at root: Sun Blade 2500 (Silver)
> > > "SUNW,UltraSPARC-IIIi" at mainbus0 not configured
> > > cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > > cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > > external (64 b/l)
> > > "memory-controller" at mainbus0 not configured
> > > "memory-controller" at mainbus0 not configured
> > > schizo0 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0
> > > schizo0: dvma map c0000000-dfffffff
> > > pci0 at schizo0
> > > bge0 at pci0 dev 3 function 0 "Broadcom BCM5703" rev 0x00,
> > > BCM5702/5703 A2 (0x1002)bge0: nvram lock timed out
> > > : ivec 0x71c, address 00:03:ba:f2:ee:53
> > > brgphy0 at bge0 phy 1: BCM5703 10/100/1000baseT PHY, rev. 2
> > > "ppm" at mainbus0 not configured
> > > schizo1 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0
> > > schizo1: dvma map c0000000-dfffffff
> > > pci1 at schizo1
> > > mpi0 at pci1 dev 4 function 0 "Symbios Logic 53c1030" rev 0x07: ivec 0x769
> > > mpi0: 0, firmware 1.3.11.1
> > > scsibus0 at mpi0: 16 targets, initiator 7
> > > sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > > sd0: 140009MB, 512 bytes/sector, 286739329 sectors
> > > mpi0: target 0 Sync at 160MHz width 16bit offset 63 QAS 1 DT 1 IU 1
> > > mpi1 at pci1 dev 4 function 1 "Symbios Logic 53c1030" rev 0x07: ivec 0x768
> > > mpi1: 0, firmware 1.3.11.1
> > > scsibus1 at mpi1: 16 targets, initiator 7
> > > schizo2 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 1
> > > schizo2: dvma map c0000000-dfffffff
> > > pci2 at schizo2
> > > ebus0 at pci2 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
> > > "flashprom" at ebus0 addr 0-fffff not configured
> > > rtc0 at ebus0 addr 70-71: m5823
> > > "i2c" at ebus0 addr 320-321 ivec 0x2e not configured
> > > "power" at ebus0 addr 800-82f ivec 0x20 not configured
> > > com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo
> > > com0: console
> > > com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo
> > > "dma" at ebus0 addr 0-ffff not configured
> > > "Acer Labs M7101 Power" rev 0x00 at pci2 dev 6 function 0 not configured
> > > "Acer Labs M5451 Audio" rev 0x02 at pci2 dev 8 function 0 not configured
> > > ohci0 at pci2 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > > 0x7a7, version 1.0, legacy support
> > > ohci1 at pci2 dev 11 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > > 0x7a6, version 1.0, legacy support
> > > pciide0 at pci2 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4:
> > > DMA, channel 0 configured to native-PCI, channel 1 configured to
> > > native-PCI
> > > pciide0: using ivec 0x798 for native-PCI interrupt
> > > pciide0: channel 0 disabled (no drives)
> > > atapiscsi0 at pciide0 channel 1 drive 0
> > > scsibus2 at atapiscsi0: 2 targets
> > > cd0 at scsibus2 targ 0 lun 0: <TSSTcorp, CDW/DVD TS-H492C, SI00> removable
> > > cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> > > radeonfb0 at pci2 dev 2 function 0 "ATI Radeon VE" rev 0x00
> > > radeonfb0: SUNW,375-3181, 1152x900
> > > wsdisplay0 at radeonfb0
> > > wsdisplay0: screen 0 added (std, sun emulation)
> > > ppb0 at pci2 dev 4 function 0 "TI PCI2250" rev 0x02
> > > pci3 at ppb0 bus 1
> > > ohci2 at pci3 dev 8 function 0 "NEC USB" rev 0x43: ivec 0x794, version 1.0
> > > ohci3 at pci3 dev 8 function 1 "NEC USB" rev 0x43: ivec 0x795, version 1.0
> > > ehci0 at pci3 dev 8 function 2 "NEC USB" rev 0x04: ivec 0x796
> > > usb0 at ehci0: USB revision 2.0
> > > uhub0 at usb0 configuration 1 interface 0 "NEC EHCI root hub" rev
> > > 2.00/1.00 addr 1
> > > "TI TSB43AB23 FireWire" rev 0x00 at pci3 dev 11 function 0 not configured
> > > usb1 at ohci2: USB revision 1.0
> > > uhub1 at usb1 configuration 1 interface 0 "NEC OHCI root hub" rev
> > > 1.00/1.00 addr 1
> > > usb2 at ohci3: USB revision 1.0
> > > uhub2 at usb2 configuration 1 interface 0 "NEC OHCI root hub" rev
> > > 1.00/1.00 addr 1
> > > usb3 at ohci0: USB revision 1.0
> > > uhub3 at usb3 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > > rev 1.00/1.00 addr 1
> > > usb4 at ohci1: USB revision 1.0
> > > uhub4 at usb4 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > > rev 1.00/1.00 addr 1
> > > "ppm" at mainbus0 not configured
> > > schizo3 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0
> > > schizo3: dvma map c0000000-dfffffff
> > > pci4 at schizo3
> > > "i2c" at mainbus0 not configured
> > > softraid0 at root
> > > scsibus3 at softraid0: 256 targets
> > > bootpath: /pci@1c,600000/network@3,0
> > > root on rd0a swap on rd0b dump on rd0b
> > >
> > > dmesg 6.6:
> > > console is /pci@1e,600000/isa@7/serial@0,3f8
> > > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > > The Regents of the University of California. All rights reserved.
> > > Copyright (c) 1995-2019 OpenBSD. All rights reserved.
> > > https://www.OpenBSD.org
> > >
> > > OpenBSD 6.6 (GENERIC.MP) #88: Sat Oct 12 10:16:48 MDT 2019
> > >
> > > dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/GENERIC.MP
> > > real mem = 2147483648 (2048MB)
> > > avail mem = 2092843008 (1995MB)
> > > mpath0 at root
> > > scsibus0 at mpath0: 256 targets
> > > mainbus0 at root: Sun Blade 2500 (Silver)
> > > cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > > cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > > external (64 b/l)
> > > cpu1 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > > cpu1: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > > external (64 b/l)
> > > "memory-controller" at mainbus0 not configured
> > > "memory-controller" at mainbus0 not configured
> > > schizo0 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0
> > > schizo0: dvma map c0000000-dfffffff
> > > pci0 at schizo0
> > > bge0 at pci0 dev 3 function 0 "Broadcom BCM5703" rev 0x00,
> > > BCM5702/5703 A2 (0x1002): ivec 0x71c, address 00:03:ba:f2:ee:53
> > > brgphy0 at bge0 phy 1: BCM5703 10/100/1000baseT PHY, rev. 2
> > > "ppm" at mainbus0 not configured
> > > schizo1 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0
> > > schizo1: dvma map c0000000-dfffffff
> > > pci1 at schizo1
> > > mpi0 at pci1 dev 4 function 0 "Symbios Logic 53c1030" rev 0x07: ivec 0x769
> > > mpi0: 0, firmware 1.3.11.1
> > > scsibus1 at mpi0: 16 targets, initiator 7
> > > sym0 at scsibus1 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > > sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > > sd0: 140009MB, 512 bytes/sector, 286739329 sectors
> > > mpi0: target 0 Sync at 160MHz width 16bit offset 63 QAS 1 DT 1 IU 1
> > > mpi1 at pci1 dev 4 function 1 "Symbios Logic 53c1030" rev 0x07: ivec 0x768
> > > mpi1: 0, firmware 1.3.11.1
> > > scsibus2 at mpi1: 16 targets, initiator 7
> > > schizo2 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 1
> > > schizo2: dvma map c0000000-dfffffff
> > > pci2 at schizo2
> > > ebus0 at pci2 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
> > > "flashprom" at ebus0 addr 0-fffff not configured
> > > rtc0 at ebus0 addr 70-71: m5823
> > > pcfiic0 at ebus0 addr 320-321 ivec 0x2e
> > > iic0 at pcfiic0
> > > "SUNW,i2c-imax" at iic0 addr 0x9 not configured
> > > "pca9556" at iic0 addr 0x18 not configured
> > > "SUNW,i2c-auxfan1" at iic0 addr 0x29 not configured
> > > admtt0 at iic0 addr 0x2c
> > > admtt1 at iic0 addr 0x2e
> > > "fm3560" at iic0 addr 0x37 not configured
> > > "fm3560" at iic0 addr 0x4e not configured
> > > spdmem0 at iic0 addr 0x5d: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > > spdmem1 at iic0 addr 0x5e: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > > spdmem2 at iic0 addr 0x65: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > > spdmem3 at iic0 addr 0x66: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > > "ics951601" at iic0 addr 0x69 not configured
> > > power0 at ebus0 addr 800-82f ivec 0x20
> > > com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo
> > > com0: console
> > > com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo
> > > "dma" at ebus0 addr 0-ffff not configured
> > > alipm0 at pci2 dev 6 function 0 "Acer Labs M7101 Power" rev 0x00: 223KHz
> > > clock
> > > iic1 at alipm0
> > > "scm001" at alipm0 addr 0x20 skipped due to alipm0 bugs
> > > autri0 at pci2 dev 8 function 0 "Acer Labs M5451 Audio" rev 0x02: ivec
> > > 0x7a4
> > > ac97: codec id 0x41445348 (Analog Devices AD1881A)
> > > ac97: codec features headphone, Analog Devices Phat Stereo
> > > audio0 at autri0
> > > midi0 at autri0: <4DWAVE MIDI UART>
> > > ohci0 at pci2 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > > 0x7a7, version 1.0, legacy support
> > > ohci1 at pci2 dev 11 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > > 0x7a6, version 1.0, legacy support
> > > pciide0 at pci2 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4:
> > > DMA, channel 0 configured to native-PCI, channel 1 configured to
> > > native-PCI
> > > pciide0: using ivec 0x798 for native-PCI interrupt
> > > pciide0: channel 0 disabled (no drives)
> > > atapiscsi0 at pciide0 channel 1 drive 0
> > > scsibus3 at atapiscsi0: 2 targets
> > > cd0 at scsibus3 targ 0 lun 0: <TSSTcorp, CDW/DVD TS-H492C, SI00> removable
> > > cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> > > radeondrm0 at pci2 dev 2 function 0 "ATI Radeon VE" rev 0x00
> > > drm0 at radeondrm0
> > > radeondrm0: ivec 0x78c
> > > ppb0 at pci2 dev 4 function 0 "TI PCI2250" rev 0x02
> > > pci3 at ppb0 bus 1
> > > ohci2 at pci3 dev 8 function 0 "NEC USB" rev 0x43: ivec 0x794, version 1.0
> > > ohci3 at pci3 dev 8 function 1 "NEC USB" rev 0x43: ivec 0x795, version 1.0
> > > ehci0 at pci3 dev 8 function 2 "NEC USB" rev 0x04: ivec 0x796
> > > usb0 at ehci0: USB revision 2.0
> > > uhub0 at usb0 configuration 1 interface 0 "NEC EHCI root hub" rev
> > > 2.00/1.00 addr 1
> > > "TI TSB43AB23 FireWire" rev 0x00 at pci3 dev 11 function 0 not configured
> > > usb1 at ohci2: USB revision 1.0
> > > uhub1 at usb1 configuration 1 interface 0 "NEC OHCI root hub" rev
> > > 1.00/1.00 addr 1
> > > usb2 at ohci3: USB revision 1.0
> > > uhub2 at usb2 configuration 1 interface 0 "NEC OHCI root hub" rev
> > > 1.00/1.00 addr 1
> > > usb3 at ohci0: USB revision 1.0
> > > uhub3 at usb3 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > > rev 1.00/1.00 addr 1
> > > usb4 at ohci1: USB revision 1.0
> > > uhub4 at usb4 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > > rev 1.00/1.00 addr 1
> > > "ppm" at mainbus0 not configured
> > > schizo3 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0
> > > schizo3: dvma map c0000000-dfffffff
> > > pci4 at schizo3
> > > "i2c" at mainbus0 not configured
> > > vscsi0 at root
> > > scsibus4 at vscsi0: 256 targets
> > > softraid0 at root
> > > scsibus5 at softraid0: 256 targets
> > > bootpath: /pci@1d,700000/scsi@4,0/disk@0,0
> > > root on sd0a (c38700025a879733.a) swap on sd0b dump on sd0b
> > > initializing kernel modesetting (RV100 0x1002:0x5159 0x1002:0x0908 0x00).
> > > BIOS signature incorrect 0 0
> > > radeondrm0: 1152x900, 8bpp
> > > wsdisplay0 at radeondrm0 mux 1
> > > wsdisplay0: screen 0 added (std, sun emulation)
> > >
> > > 6.7-beta after installing it with the 6.6 bsd.rd:
> > >
> > > OpenBSD IEEE 1275 Bootblock 2.0
> > > ..>> OpenBSD BOOT 1.17
> > > Trying bsd...
> > > Booting /pci@1d,700000/scsi@4/disk@0,0:a/bsd
> > > 11196424@0x1000000+2040@0x1aad808+188272@0x1c00000+4006032@0x1c2df70
> > > symbols @ 0xfec46440 175+587856+405269 start=0x1000000
> > > [ using 994392 bytes of bsd ELF symbol table ]
> > > console is /pci@1e,600000/isa@7/serial@0,3f8
> > > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > > The Regents of the University of California. All rights
> > > reserved.
> > > Copyright (c) 1995-2020 OpenBSD. All rights reserved.
> > > https://www.OpenBSD.org
> > >
> > > OpenBSD 6.7-beta (GENERIC.MP) #270: Mon Apr 6 18:39:29 MDT 2020
> > >
> > > dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/GENERIC.MP
> > > real mem = 2147483648 (2048MB)
> > > avail mem = 2091376640 (1994MB)
> > > mpath0 at root
> > > scsibus0 at mpath0: 256 targets
> > > mainbus0 at root: Sun Blade 2500 (Silver)
> > > cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > > cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > > external (64 b/l)
> > > cpu1 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > > cpu1: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > > external (64 b/l)
> > > "memory-controller" at mainbus0 not configured
> > > "memory-controller" at mainbus0 not configured
> > > schizo0 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0
> > > schizo0: dvma map c0000000-dfffffff
> > > pci0 at schizo0
> > > bge0 at pci0 dev 3 function 0 "Broadcom BCM5703" rev 0x00,
> > > BCM5702/5703 A2 (0x1002): ivec 0x71c, address 00:03:ba:f2:ee:53
> > > brgphy0 at bge0 phy 1: BCM5703 10/100/1000baseT PHY, rev. 2
> > > "ppm" at mainbus0 not configured
> > > schizo1 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0
> > > schizo1: dvma map c0000000-dfffffff
> > > pci1 at schizo1
> > > mpi0 at pci1 dev 4 function 0 "Symbios Logic 53c1030" rev 0x07: ivec
> > > 0x769
> > > mpi0: 0, firmware 1.3.11.1
> > > scsibus1 at mpi0: 16 targets, initiator 7
> > > sym0 at scsibus1 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > > sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > > sd0: 140009MB, 512 bytes/sector, 286739329 sectors
> > > mpi0: target 0 Sync at 160MHz width 16bit offset 63 QAS 1 DT 1 IU 1
> > > mpi1 at pci1 dev 4 function 1 "Symbios Logic 53c1030" rev 0x07: ivec
> > > 0x768
> > > mpi1: 0, firmware 1.3.11.1
> > > scsibus2 at mpi1: 16 targets, initiator 7
> > > schizo2 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 1
> > > schizo2: dvma map c0000000-dfffffff
> > > pci2 at schizo2
> > > ebus0 at pci2 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
> > > "flashprom" at ebus0 addr 0-fffff not configured
> > > rtc0 at ebus0 addr 70-71: m5823
> > > pcfiic0 at ebus0 addr 320-321 ivec 0x2e
> > > iic0 at pcfiic0
> > > "SUNW,i2c-imax" at iic0 addr 0x9 not configured
> > > "pca9556" at iic0 addr 0x18 not configured
> > > "SUNW,i2c-auxfan1" at iic0 addr 0x29 not configured
> > > admtt0 at iic0 addr 0x2c
> > > admtt1 at iic0 addr 0x2e
> > > "fm3560" at iic0 addr 0x37 not configured
> > > "fm3560" at iic0 addr 0x4e not configured
> > > spdmem0 at iic0 addr 0x5d: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > > spdmem1 at iic0 addr 0x5e: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > > spdmem2 at iic0 addr 0x65: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > > spdmem3 at iic0 addr 0x66: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > > "ics951601" at iic0 addr 0x69 not configured
> > > power0 at ebus0 addr 800-82f ivec 0x20
> > > com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo
> > > com0: console
> > > com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo
> > > "dma" at ebus0 addr 0-ffff not configured
> > > alipm0 at pci2 dev 6 function 0 "Acer Labs M7101 Power" rev 0x00:
> > > 223KHz clock
> > > iic1 at alipm0
> > > "scm001" at alipm0 addr 0x20 skipped due to alipm0 bugs
> > > autri0 at pci2 dev 8 function 0 "Acer Labs M5451 Audio" rev 0x02: ivec
> > > 0x7a4
> > > ac97: codec id 0x41445348 (Analog Devices AD1881A)
> > > ac97: codec features headphone, Analog Devices Phat Stereo
> > > audio0 at autri0
> > > midi0 at autri0: <4DWAVE MIDI UART>
> > > ohci0 at pci2 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > > 0x7a7, version 1.0, legacy support
> > > ohci1 at pci2 dev 11 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > > 0x7a6, version 1.0, legacy support
> > > pciide0 at pci2 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4:
> > > DMA, channel 0 configured to native-PCI, channel 1 configured to
> > > native-PCI
> > > pciide0: using ivec 0x798 for native-PCI interrupt
> > > pciide0: channel 0 disabled (no drives)
> > > atapiscsi0 at pciide0 channel 1 drive 0
> > > scsibus3 at atapiscsi0: 2 targets
> > > cd0 at scsibus3 targ 0 lun 0: <TSSTcorp, CDW/DVD TS-H492C, SI00>
> > > removable
> > > cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> > > radeondrm0 at pci2 dev 2 function 0 "ATI Radeon VE" rev 0x00
> > > drm0 at radeondrm0
> > > radeondrm0: ivec 0x78c
> > > ppb0 at pci2 dev 4 function 0 "TI PCI2250" rev 0x02
> > > pci3 at ppb0 bus 1
> > > ohci2 at pci3 dev 8 function 0 "NEC USB" rev 0x43: ivec 0x794, version
> > > 1.0
> > > ohci3 at pci3 dev 8 function 1 "NEC USB" rev 0x43: ivec 0x795, version
> > > 1.0
> > > ehci0 at pci3 dev 8 function 2 "NEC USB" rev 0x04: ivec 0x796
> > > usb0 at ehci0: USB revision 2.0
> > > uhub0 at usb0 configuration 1 interface 0 "NEC EHCI root hub" rev
> > > 2.00/1.00 addr 1
> > > "TI TSB43AB23 FireWire" rev 0x00 at pci3 dev 11 function 0 not
> > > configured
> > > usb1 at ohci2: USB revision 1.0
> > > uhub1 at usb1 configuration 1 interface 0 "NEC OHCI root hub" rev
> > > 1.00/1.00 addr 1
> > > usb2 at ohci3: USB revision 1.0
> > > uhub2 at usb2 configuration 1 interface 0 "NEC OHCI root hub" rev
> > > 1.00/1.00 addr 1
> > > usb3 at ohci0: USB revision 1.0
> > > uhub3 at usb3 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > > rev 1.00/1.00 addr 1
> > > usb4 at ohci1: USB revision 1.0
> > > uhub4 at usb4 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > > rev 1.00/1.00 addr 1
> > > "ppm" at mainbus0 not configured
> > > schizo3 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0
> > > schizo3: dvma map c0000000-dfffffff
> > > pci4 at schizo3
> > > "i2c" at mainbus0 not configured
> > > vscsi0 at root
> > > scsibus4 at vscsi0: 256 targets
> > > softraid0 at root
> > > scsibus5 at softraid0: 256 targets
> > > bootpath: /pci@1d,700000/scsi@4,0/disk@0,0
> > > root on sd0a (c7e58360e1193129.a) swap on sd0b dump on sd0b
> > > initializing kernel modesetting (RV100 0x1002:0x5159 0x1002:0x0908 0x00).
> > > BIOS signature incorrect 0 0
> > > radeon_cp: Failed to load firmware "radeon/R100_cp.bin"
> > > [drm] *ERROR* Failed to load firmware!
> > > drm:pid0:r100_startup *ERROR* failed initializing CP (-2).
> > > drm:pid0:r100_init *ERROR* Disabling GPU acceleration
> > > radeondrm0: 1152x900, 8bpp
> > > wsdisplay0 at radeondrm0 mux 1
> > > wsdisplay0: screen 0 added (std, sun emulation)
> > > Automatic boot in progress: starting file system checks.
> > > /dev/sd0a (c7e58360e1193129.a): file system is clean; not checking
> > > /dev/sd0k (c7e58360e1193129.k): file system is clean; not checking
> > > /dev/sd0d (c7e58360e1193129.d): file system is clean; not checking
> > > /dev/sd0f (c7e58360e1193129.f): file system is clean; not checking
> > > /dev/sd0g (c7e58360e1193129.g): file system is clean; not checking
> > > /dev/sd0h (c7e58360e1193129.h): file system is clean; not checking
> > > /dev/sd0j (c7e58360e1193129.j): file system is clean; not checking
> > > /dev/sd0i (c7e58360e1193129.i): file system is clean; not checking
> > > /dev/sd0e (c7e58360e1193129.e): file system is clean; not checking
> > > pf enabled
> > > starting network
> > > bge0: 192.168.2.131 lease accepted from 192.168.2.1 (fe:e1:ba:d2:bf:d6)
> > > reordering libraries:Illegal instruction (core dumped)
> > > Illegal instruction (core dumped)
> > > Illegal instruction (core dumped)
> > > failed.
> > > Illegal instruction (core dumped)
> > > openssl: generating isakmpd/iked RSA keys... failed.
> > > cp: /etc/isakmpd/private/local.key: No such file or directory
> > > chmod: /etc/iked/private/local.key: No such file or directory
> > > cp: /etc/isakmpd/local.pub: No such file or directory
> > > Segmentation fault (core dumped)
> > > Illegal instruction (core dumped)
> > > starting early daemons:Illegal instruction (core dumped)
> > > Illegal instruction (core dumped)
> > > usage: /etc/rc.d/syslogd [-df] start|stop|restart|reload|check
> > > Illegal instruction (core dumped)
> > > Illegal instruction (core dumped)
> > > usage: /etc/rc.d/pflogd [-df] start|stop|restart|reload|check
> > > Illegal instruction (core dumped)
> > > Illegal instruction (core dumped)
> > > usage: /etc/rc.d/ntpd [-df] start|stop|restart|check
> > > .
> > > starting RPC daemons:.
> > > savecore: no core dump
> > > checking quotas: done.
> > > Illegal instruction (core dumped)
> > > Illegal instruction (core dumped)
> > > Illegal instruction (core dumped)
> > > clearing /tmp
> > > Illegal instruction (core dumped)
> > > kern.securelevel: 0 -> 1
> > > Illegal instruction (core dumped)
> > > creating runtime link editor directory cache.
> > > preserving editor files.
> > > Illegal instruction (core dumped)
> > > starting network daemons:Illegal instruction (core dumped)
> > > Illegal instruction (core dumped)
> > > usage: /etc/rc.d/sshd [-df] start|stop|restart|reload|check
> > > Illegal instruction (core dumpeddev = 0x700, block = 25904, fs = /
> > > panic: ffs_blkfree: freeing free block
> > > Stopped at db_enter+0x8: nop
> > > TID PID UID PRFLAGS PFLAGS CPU COMMAND
> > > *176722 48187 0 0x100803 0x2000 1K grep
> > > panic(1, 4002753d318, 1c24758, 100, 1cba000, 0) at panic+0x148
> > > ffs_blkfree(1950000, ca6, d5e, 40004542800, 6530, 4000ee82000) at
> > > ffs_blkfree+0
> > > x800
> > > ffs_indirtrunc(400041c25c0, f6c, 6530, 0, 86, fffffffffffff002) at
> > > ffs_indirtru
> > > nc+0x384
> > > ffs_truncate(400041c25c0, 0, 0, 0, 2, 0) at ffs_truncate+0xb28
> > > ufs_setattr(4002753d828, 40004315ce0, 400041c25c0, 400042fd0c0, 1545aa0,
> > > 1) at u
> > > fs_setattr+0x408
> > > VOP_SETATTR(400042fd0c0, 175867c, 1, 400042aaf30, 1aad000,
> > > bceb5949771b0976) at
> > > VOP_SETATTR+0x54
> > > coredump(400042aaf30, 1c8e6f8, 40004200000, 40004315ce0, 4002753d938,
> > > 400042fd0
> > > c0) at coredump+0x380
> > > sigexit(400042aaf30, 4, 0, 50, 1, 0) at sigexit+0x9c
> > > postsig(400042aaf30, 4, 400042a9b20, 4, 0, 1aad000) at postsig+0x1b8
> > > userret(400042aaf30, 400042aafc0, 8, 0, 0, 400042a9b20) at userret+0xd4
> > > trap(4002753ded0, fab193, 211e88b3a0, 400042aaf30, 1aad000, fa8000) at
> > > trap+0x9
> > > 40
> > > Lslowtrap_reenter(2102bd2000, 450, 3, 1002, ffffffffffffffff, 0) at
> > > Lslowtrap_r
> > > eenter+0xf8
> > > https://www.openbsd.org/ddb.html describes the minimum info required in
> > > bug
> > > reports. Insufficient info makes it difficult to find and fix bugs.
> > > ddb{1}> trace
> > > panic(1, 4002753d318, 1c24758, 100, 1cba000, 0) at panic+0x148
> > > ffs_blkfree(1950000, ca6, d5e, 40004542800, 6530, 4000ee82000) at
> > > ffs_blkfree+0
> > > x800
> > > ffs_indirtrunc(400041c25c0, f6c, 6530, 0, 86, fffffffffffff002) at
> > > ffs_indirtru
> > > nc+0x384
> > > ffs_truncate(400041c25c0, 0, 0, 0, 2, 0) at ffs_truncate+0xb28
> > > ufs_setattr(4002753d828, 40004315ce0, 400041c25c0, 400042fd0c0, 1545aa0,
> > > 1) at u
> > > fs_setattr+0x408
> > > VOP_SETATTR(400042fd0c0, 175867c, 1, 400042aaf30, 1aad000,
> > > bceb5949771b0976) at
> > > VOP_SETATTR+0x54
> > > coredump(400042aaf30, 1c8e6f8, 40004200000, 40004315ce0, 4002753d938,
> > > 400042fd0
> > > c0) at coredump+0x380
> > > sigexit(400042aaf30, 4, 0, 50, 1, 0) at sigexit+0x9c
> > > postsig(400042aaf30, 4, 400042a9b20, 4, 0, 1aad000) at postsig+0x1b8
> > > userret(400042aaf30, 400042aafc0, 8, 0, 0, 400042a9b20) at userret+0xd4
> > > trap(4002753ded0, fab193, 211e88b3a0, 400042aaf30, 1aad000, fa8000) at
> > > trap+0x9
> > > 40
> > > Lslowtrap_reenter(2102bd2000, 450, 3, 1002, ffffffffffffffff, 0) at
> > > Lslowtrap_r
> > > eenter+0xf8
> > > ddb{1}> ps
> > > PID TID PPID UID S FLAGS WAIT COMMAND
> > > *48187 176722 88537 0 7 0x102803 grep
> > > 88537 382815 99841 0 3 0x10008b pause ksh
> > > 66999 94861 1 77 3 0x100090 poll dhclient
> > > 48420 280249 1 0 3 0x80 poll dhclient
> > > 40518 319937 85231 115 3 0x100092 kqread slaacd
> > > 85838 489306 85231 115 3 0x100092 kqread slaacd
> > > 85231 202308 1 0 3 0x100080 kqread slaacd
> > > 99841 236206 1 0 3 0x10008b pause sh
> > > 81405 79355 0 0 3 0x14200 bored radeon-crtc
> > > 71770 73324 0 0 3 0x14200 bored radeon-crtc
> > > 59905 423050 0 0 3 0x14200 bored ttm_swap
> > > 63119 314087 0 0 3 0x14200 bored smr
> > > 97636 219885 0 0 3 0x14200 pgzero zerothread
> > > 1514 49286 0 0 3 0x14200 aiodoned aiodoned
> > > 14539 49447 0 0 3 0x14200 syncer update
> > > 9416 340174 0 0 3 0x14200 cleaner cleaner
> > > 87399 2990 0 0 3 0x14200 reaper reaper
> > > 50862 213556 0 0 3 0x14200 pgdaemon pagedaemon
> > > 92067 192338 0 0 3 0x14200 bored crynlk
> > > 54009 434311 0 0 3 0x14200 bored crypto
> > > 37503 355741 0 0 3 0x14200 usbtsk usbtask
> > > 75750 328255 0 0 3 0x14200 usbatsk usbatsk
> > > 13762 140473 0 0 3 0x14200 bored drmtskl
> > > 28060 134348 0 0 3 0x14200 bored drmlwq
> > > 37420 87687 0 0 3 0x14200 bored drmlwq
> > > 47187 479949 0 0 3 0x14200 bored drmlwq
> > > 63862 19851 0 0 3 0x14200 bored drmlwq
> > > 20716 145865 0 0 3 0x14200 bored drmubwq
> > > 9815 176299 0 0 3 0x14200 bored drmubwq
> > > 61058 227276 0 0 3 0x14200 bored drmubwq
> > > 68348 317421 0 0 3 0x14200 bored drmubwq
> > > 10263 108304 0 0 3 0x14200 bored drmwq
> > > 59225 524108 0 0 3 0x14200 bored drmwq
> > > 47024 166127 0 0 3 0x14200 bored drmwq
> > > 97890 482048 0 0 3 0x14200 bored drmwq
> > > 16681 130387 0 0 3 0x14200 bored sensors
> > > 79577 459066 0 0 3 0x40014200 idle1
> > > 30879 347784 0 0 3 0x14200 bored softnet
> > > 73065 27334 0 0 3 0x14200 bored systqmp
> > > 96778 411122 0 0 3 0x14200 bored systq
> > > 85835 217328 0 0 3 0x40014200 bored softclock
> > > 71127 1246 0 0 7 0x40014200 idle0
> > > 96626 508362 0 0 3 0x14200 kmalloc kmthread
> > > 1 419877 0 0 3 0x82 wait init
> > > 0 0 -1 0 3 0x10200 scheduler swapper
> > > ddb{1}> machine ddbcpu 0
> > > panic: kernel data fault: pc=182bab4 addr=182a000
> > > Stopped at _kernel_lock+0xd0: ld [%i0 + 0x800], %i3
> > > intr_handler(e0017b80, 4000449e800, 0, 6, 6c, 1cbff48) at
> > > intr_handler+0x30
> > > sparc_intr_retry(72e43b48, 72e266ba, 8, 2, 1, 1a39840) at
> > > sparc_intr_retry+0x5c
> > >
> > > sys_tickintr(1cd165c, 2018000, 2b1e8, 2b1e7, 2b1e7, 2b1e8) at
> > > sys_tickintr+0xc4
> > >
> > > intr_handler(e0017ec8, 4000431e300, 0, 1, 0, 1f195) at intr_handler+0x30
> > > sparc_intr_retry(3, 0, 0, 0, 2018000, 1aad000) at sparc_intr_retry+0x5c
> > > sched_idle(2018000, 2018140, 1c8f2f8, 1903fde, 400042ee780, 1caf5f0) at
> > > sched_i
> > > dle+0x27c
> > > proc_trampoline(0, 0, 0, 0, 0, 0) at proc_trampoline+0x14
> > > ddb{0}> trace
> > > intr_handler(e0017b80, 4000449e800, 0, 6, 6c, 1cbff48) at
> > > intr_handler+0x30
> > > sparc_intr_retry(72e43b48, 72e266ba, 8, 2, 1, 1a39840) at
> > > sparc_intr_retry+0x5c
> > >
> > > sys_tickintr(1cd165c, 2018000, 2b1e8, 2b1e7, 2b1e7, 2b1e8) at
> > > sys_tickintr+0xc4
> > >
> > > intr_handler(e0017ec8, 4000431e300, 0, 1, 0, 1f195) at intr_handler+0x30
> > > sparc_intr_retry(3, 0, 0, 0, 2018000, 1aad000) at sparc_intr_retry+0x5c
> > > sched_idle(2018000, 2018140, 1c8f2f8, 1903fde, 400042ee780, 1caf5f0) at
> > > sched_i
> > > dle+0x27c
> > > proc_trampoline(0, 0, 0, 0, 0, 0) at proc_trampoline+0x14
> > > ddb{0}> machine ddbcpu 1
> > > Stopped at db_enter+0x8: nop
> > > panic(1, 4002753c7a8, 1c24758, 104, 1cba000, 0) at panic+0x148
> > > data_access_fault(1927000, 0, 182bab4, 182a000, 182bafc, 182a000) at
> > > data_acces
> > > s_fault+0x320
> > > Ldatafault_internal(8, 80, 4002753a000, 182bae2, 1, 1013120) at
> > > Ldatafault_inte
> > > rnal+0xcc
> > > db_read_bytes(182bafc, 3, 4002753cb10, 1, 1800000, 1000000) at
> > > db_read_bytes+0x
> > > 58
> > > db_put_value(182bafc, 4002753cb0f, 0, 1aad000, ffffffffffffffff,
> > > 4002753cb10) a
> > > t db_put_value+0x6c
> > > db_set_temp_breakpoint(91d02000, 1cac990, 4, 100000000, 1aad000, 0) at
> > > db_set_t
> > > emp_breakpoint+0x74
> > > db_set_single_step(1cd69f8, 182baf8, 1000000, 1000000, 0, 0) at
> > > db_set_single_s
> > > tep+0xa8
> > > db_restart_at_pc(1cd69f8, 0, 182baf8, 0, 1cb0000, 0) at
> > > db_restart_at_pc+0xe8
> > > db_trap(1cd69f8, 1aad000, 0, 1c58000, 1, 1860000) at db_trap+0x208
> > > db_ktrap(0, 4002753d020, 1cd6bd8, 101, 1cd6c80, 1cd69f8) at db_ktrap+0x1e4
> > > trap(4002753d020, 101, 182baf4, bebf, 1aad000, 1d0006) at trap+0x1c0
> > > Lslowtrap_reenter(1c24758, 1c37bfc, 0, 0, a, 0) at Lslowtrap_reenter+0xf8
> > > printf(1, bceb5949771b0976, bceb5949771b0976, 0, 6b, 0) at printf+0x68
> > > panic(1, 4002753d318, 1c24758, 100, 1cba000, 0) at panic+0x148
> > > ddb{1}> trace
> > > panic(1, 4002753c7a8, 1c24758, 104, 1cba000, 0) at panic+0x148
> > > data_access_fault(1927000, 0, 182bab4, 182a000, 182bafc, 182a000) at
> > > data_acces
> > > s_fault+0x320
> > > Ldatafault_internal(8, 80, 4002753a000, 182bae2, 1, 1013120) at
> > > Ldatafault_inte
> > > rnal+0xcc
> > > db_read_bytes(182bafc, 3, 4002753cb10, 1, 1800000, 1000000) at
> > > db_read_bytes+0x
> > > 58
> > > db_put_value(182bafc, 4002753cb0f, 0, 1aad000, ffffffffffffffff,
> > > 4002753cb10) a
> > > t db_put_value+0x6c
> > > db_set_temp_breakpoint(91d02000, 1cac990, 4, 100000000, 1aad000, 0) at
> > > db_set_t
> > > emp_breakpoint+0x74
> > > db_set_single_step(1cd69f8, 182baf8, 1000000, 1000000, 0, 0) at
> > > db_set_single_s
> > > tep+0xa8
> > > db_restart_at_pc(1cd69f8, 0, 182baf8, 0, 1cb0000, 0) at
> > > db_restart_at_pc+0xe8
> > > db_trap(1cd69f8, 1aad000, 0, 1c58000, 1, 1860000) at db_trap+0x208
> > > db_ktrap(0, 4002753d020, 1cd6bd8, 101, 1cd6c80, 1cd69f8) at db_ktrap+0x1e4
> > > trap(4002753d020, 101, 182baf4, bebf, 1aad000, 1d0006) at trap+0x1c0
> > > Lslowtrap_reenter(1c24758, 1c37bfc, 0, 0, a, 0) at Lslowtrap_reenter+0xf8
> > > printf(1, bceb5949771b0976, bceb5949771b0976, 0, 6b, 0) at printf+0x68
> > > panic(1, 4002753d318, 1c24758, 100, 1cba000, 0) at panic+0x148
> > > ffs_blkfree(1950000, ca6, d5e, 40004542800, 6530, 4000ee82000) at
> > > ffs_blkfree+0
> > > x800
> > > ffs_indirtrunc(400041c25c0, f6c, 6530, 0, 86, fffffffffffff002) at
> > > ffs_indirtru
> > > nc+0x384
> > > ffs_truncate(400041c25c0, 0, 0, 0, 2, 0) at ffs_truncate+0xb28
> > > ufs_setattr(4002753d828, 40004315ce0, 400041c25c0, 400042fd0c0, 1545aa0,
> > > 1) at u
> > > fs_setattr+0x408
> > > VOP_SETATTR(400042fd0c0, 175867c, 1, 400042aaf30, 1aad000,
> > > bceb5949771b0976) at
> > > VOP_SETATTR+0x54
> > > coredump(400042aaf30, 1c8e6f8, 40004200000, 40004315ce0, 4002753d938,
> > > 400042fd0
> > > c0) at coredump+0x380
> > > sigexit(400042aaf30, 4, 0, 50, 1, 0) at sigexit+0x9c
> > > postsig(400042aaf30, 4, 400042a9b20, 4, 0, 1aad000) at postsig+0x1b8
> > > userret(400042aaf30, 400042aafc0, 8, 0, 0, 400042a9b20) at userret+0xd4
> > > trap(4002753ded0, fab193, 211e88b3a0, 400042aaf30, 1aad000, fa8000) at
> > > trap+0x9
> > > 40
> > > Lslowtrap_reenter(2102bd2000, 450, 3, 1002, ffffffffffffffff, 0) at
> > > Lslowtrap_r
> > > eenter+0xf8
> > >
> > >
> > > ddb{1}> boot halt
> > >
> > > RED State Exception
> > > Error enable reg: 0000.0001.00f0.001f
> > > CPU: 0000.0000.0000.0000
> > > TL=0000.0000.0000.0005 TT=0000.0000.0000.0030
> > > TPC=0000.0000.0101.067c TnPC=0000.0000.0101.0680
> > > TSTATE=0000.0000.5800.0501
> > > TL=0000.0000.0000.0004 TT=0000.0000.0000.0030
> > > TPC=0000.0000.0101.067c TnPC=0000.0000.0101.0680
> > > TSTATE=0000.0000.5800.0501
> > > TL=0000.0000.0000.0003 TT=0000.0000.0000.0030
> > > TPC=0000.0000.0101.067c TnPC=0000.0000.0101.0680
> > > TSTATE=0000.0000.5800.0501
> > > TL=0000.0000.0000.0002 TT=0000.0000.0000.0030
> > > TPC=0000.0000.0101.067c TnPC=0000.0000.0101.0680
> > > TSTATE=0000.0000.5800.0501
> > > TL=0000.0000.0000.0001 TT=0000.0000.0000.0030
> > > TPC=0000.0000.0170.4744 TnPC=0000.0000.0170.4748
> > > TSTATE=0000.0000.1d00.0601
> > >
>
