ath(4) configuration is not working in OBSD3.8-Release.
The wifi card is Netgear WG511T which is supposed to connect to a
linksys wifi gateway to get IP address from the DHCP pool and it
should have a 26-digit WEP key.
Here's the dmesg
OpenBSD 3.8 (GENERIC) #138: Sat Sep 10 15:41:37 MDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Mobile Intel(R) Pentium(R) 4 CPU 3.20GHz ("GenuineIntel"
686-class) 3.20 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,CNXT-ID
real mem = 468688896 (457704K)
avail mem = 420597760 (410740K)
using 4278 buffers containing 23535616 bytes (22984K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(81) BIOS, date 01/16/04, BIOS32 rev. 0 @ 0xfd700
pcibios0 at bios0: rev 2.1 @ 0xfd700/0x900
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf00/224 (12 entries)
pcibios0: no compatible PCI ICU found: ICU vendor 0x1002 product 0x434c
pcibios0: PCI bus #3 is the last bus
bios0: ROM list: 0xc0000/0xf000 0xd0000/0x6000! 0xd6000/0x800! 0xd8000/0x1000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ATI RS300 Host" rev 0x02
ppb0 at pci0 dev 1 function 0 "ATI Radeon IGP 9100 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon Mobility IGP 9100" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ohci0 at pci0 dev 19 function 0 "ATI SB200 USB" rev 0x01: irq 11,
version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: ATI OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1 at pci0 dev 19 function 1 "ATI SB200 USB" rev 0x01: irq 11,
version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: ATI OHCI root hub, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
ehci0 at pci0 dev 19 function 2 "ATI SB200 USB2" rev 0x01: irq 11
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: ATI EHCI root hub, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
"ATI SB200 SMBus" rev 0x17 at pci0 dev 20 function 0 not configured
pciide0 at pci0 dev 20 function 1 "ATI IXP200 IDE" rev 0x00: DMA
(unsupported), channel 0 configured to compatibility, channel 1
configured to compatibility
wd0 at pciide0 channel 0 drive 0: <HITACHI_DK23FA-60>
wd0: 16-sector PIO, LBA, 57231MB, 117210240 sectors
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TOSHIBA, DVD-ROM SD-R6112, 1031> SCSI0
5/cdrom removable
pcib0 at pci0 dev 20 function 3 "ATI SB200 PCI-ISA" rev 0x00
ppb1 at pci0 dev 20 function 4 "ATI SB200 PCI-PCI" rev 0x00
pci2 at ppb1 bus 2
"Texas Instruments TSB43AB21 FireWire" rev 0x00 at pci2 dev 0 function
0 not configured
ath0 at pci2 dev 2 function 0 "Atheros AR5212" rev 0x01: irq 11
ath0: AR5212 5.6 phy 4.1 rf5111 1.7 rf2111 2.3, WOR4W, address 00:90:96:72:4d:f1
rl0 at pci2 dev 3 function 0 "Realtek 8139" rev 0x10: irq 11 address
00:02:3f:d3:3a:7b
rlphy0 at rl0 phy 0: RTL internal phy
cbb0 at pci2 dev 4 function 0 "ENE CB-1410 CardBus" rev 0x01: irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3 device 0 cacheline 0x8, lattimer 0x20
pcmcia0 at cardslot0
auixp0 at pci0 dev 20 function 5 "ATI IXP200 AC97" rev 0x00: irq 11
auixp0: soft resetting aclink
auixp0: not up; resetting aclink hardware
auixp0: not up; resetting aclink hardware
auixp0: aclink hardware reset successful
vendor "ATI", unknown product 0x434d (class communications subclass
modem, rev 0x01) at pci0 dev 20 function 6 not configured
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask ef75 netmask ef75 ttymask fff7
pctr: user-level cycle counter enabled
ath1 at cardbus0 dev 0 function 0 "Atheros Communications, Inc.,
AR5001-0000-0000, Wireless LAN Reference Card": irq 11
ath1: AR5212 7.9 phy 4.5 rf2112 5.6 rf2112 5.6, FCC1A, address 00:0f:b5:a7:d1:f7
umass0 at uhub2 port 2 configuration 1 interface 0
umass0: LEXAR MEDIA JUMPDRIVE GEYSR, rev 2.00/0.01, addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets
sd0 at scsibus1 targ 1 lun 0: <LEXAR, GEYSER JUMPDRIVE, 1.00> SCSI1
0/direct removable
sd0: 246MB, 984 cyl, 16 head, 32 sec, 512 bytes/sec, 503808 sec total
uhidev0 at uhub0 port 3 configuration 1 interface 0
uhidev0: vendor 0x062a product 0x0001, rev 1.10/0.00, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse1 at ums0 mux 0
dkcsum: wd0 matches BIOS drive 0x80
dkcsum: sd0 matches BIOS drive 0x81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
ac97: codec id 0x414c4740 (Avance Logic ALC202)
ac97: codec features headphone, 20 bit DAC, 18 bit ADC, Realtek 3D
audio0 at auixp0
ar5k_ar5212_nic_wakeup: failed to resume the AR5212 (again)
ath1: unable to reset hardware; hal status 3598540404
pppoe0: phase establish
ar5k_ar5212_nic_wakeup: failed to resume the AR5212 (again)
ath1: unable to reset hardware; hal status 3888999724
ar5k_ar5212_nic_wakeup: failed to resume the AR5212 (again)
ath1: unable to reset hardware; hal status 3888999724
ar5k_ar5212_nic_wakeup: failed to resume the AR5212 (again)
ath1: unable to reset hardware; hal status 3888999724
Here's the ifconfig -a output:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33224
groups: lo
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
ath0: flags=8863<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:90:96:72:4d:f1
media: IEEE802.11 autoselect (DS1)
status: no network
ieee80211: nwid ""
inet6 fe80::290:96ff:fe72:4df1%ath0 prefixlen 64 scopeid 0x1
rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:02:3f:d3:3a:7b
groups: egress
media: Ethernet autoselect (100baseTX full-duplex)
status: active
inet6 fe80::202:3fff:fed3:3a7b%rl0 prefixlen 64 scopeid 0x2
inet 192.168.1.60 netmask 0xffffff00 broadcast 192.168.1.255
pflog0: flags=0<> mtu 33224
pfsync0: flags=0<> mtu 1348
enc0: flags=0<> mtu 1536
ath1: flags=8863<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:0f:b5:a7:d1:f7
media: IEEE802.11 autoselect (DS1)
status: no network
ieee80211: nwid insignia nwkey 0x88d67bbfa7037e7d73e2bb987e
inet6 fe80::20f:b5ff:fea7:d1f7%ath1 prefixlen 64 scopeid 0x7
inet 192.168.1.60 netmask 0xffffff00 broadcast 192.168.1.255
pppoe0: flags=8851<UP,POINTOPOINT,RUNNING,SIMPLEX,MULTICAST> mtu 1492
dev: state: PADI sent
sid: 0x0 PADI retries: 0 PADR retries: 0
groups: pppoe
inet 0.0.0.0 --> 0.0.0.1 netmask 0xffffffff
inet6 fe80::290:96ff:fe72:4df1%pppoe0 -> prefixlen 64 scopeid 0x8
Here's the /etc/hostname.ath1
up
dhcp media autoselect nwkey 0x88d67bbfa7037e7d73e2bb987e channel 11
