Re: edgerouter 6 / rdomain at boot

Holger Glaess Mon, 02 Jul 2018 22:32:15 -0700

hi


Am 02.07.2018 um 09:24 schrieb Claudio Jeker:

On Sun, Jul 01, 2018 at 06:26:04AM +0200, Holger Glaess wrote:

hi


normaly work this on intel ,

farin# cat /etc/hostname.lo2

rdomain 2
inet 127.0.0.1/8

This stopped working some time ago. Now lo2 is automatically created when
rdomain 2 is created. The problem is that actually /etc/netstart is
creating the loopback interface first and so when trying to create lo2 for
rdomain 2 the code fails.

i renumberd my rdomains from 1 to 10 and so on , and then they bootas espected.

For now I suggest you remove '/etc/hostname.lo2' and move the route
commands to '/etc/hostname.cnmac3' along with
'!/sbin/ifconfig lo2 inet 127.0.0.1/8'

This needs to be reconsidered, I wanted to auto assign loopback networks
on all lo(4) interfaces which are auto created but failed until now.
Will look into this at g2k18 again

Also you can use rcctl to boot services in different rdomains.
Symlink the ftp-proxy rc script to e.g. ftp-proxy_r2
rcctl enable ftp-proxy_r2
rcctl set ftp-proxy_r2 rtable 2
rcctl start ftp-proxy_r2

since when is this rcctl enhancement working ?

in my current from 29.6. is not


holger

!/sbin/route -n -T 2 exec /usr/sbin/ftp-proxy -D 7
!/sbin/route -n -T 2 add default 127.0.0.1


farin# cat /etc/hostname.cnmac3

rdomain 2
inet 192.168.132.252/24
up


but if i boot the Edgerouter , i got 3 times the message

ifconfig: SIOCSIFRDOMAIN: File exists


and cnmac3 ist not in rdomain 2


if do an manual

sh /etc/netstart cnmac3

everything is fine.


i use 6.3 current see dmesg bellow


any clue for me ?

holger



Copyright (c) 1982, 1986, 1989, 1991, 1993
         The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2018 OpenBSD. All rights reserved.
https://www.OpenBSD.org

OpenBSD 6.3-current (GENERIC.MP) #0: Sun Jun 24 03:55:02 UTC 2018
     visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC.MP
real mem = 1073741824 (1024MB)
avail mem = 1038057472 (989MB)
mainbus0 at root: board 20300 rev 1.20
cpu0 at mainbus0: CN70xx/CN71xx CPU rev 0.2 1000 MHz, CN70xx/CN71xx FPU rev
0.0
cpu0: cache L1-I 78KB 39 way D 32KB 32 way, L2 1024KB 8 way
cpu1 at mainbus0: CN70xx/CN71xx CPU rev 0.2 1000 MHz, CN70xx/CN71xx FPU rev
0.0
cpu1: cache L1-I 78KB 39 way D 32KB 32 way, L2 1024KB 8 way
cpu2 at mainbus0: CN70xx/CN71xx CPU rev 0.2 1000 MHz, CN70xx/CN71xx FPU rev
0.0
cpu2: cache L1-I 78KB 39 way D 32KB 32 way, L2 1024KB 8 way
cpu3 at mainbus0: CN70xx/CN71xx CPU rev 0.2 1000 MHz, CN70xx/CN71xx FPU rev
0.0
cpu3: cache L1-I 78KB 39 way D 32KB 32 way, L2 1024KB 8 way
clock0 at mainbus0: int 5
octcrypto0 at mainbus0
iobus0 at mainbus0
simplebus0 at iobus0: "soc"
octciu0 at simplebus0
octcib0 at simplebus0: max-bits 23pass out quick on $wlan_vif inet proto udp 
from $fritzbox_wan to 192.168.133.0/24 rtable 1
octcib1 at simplebus0: max-bits 12
octcib2 at simplebus0: max-bits 6
octcib3 at simplebus0: max-bits 15
octcib4 at simplebus0: max-bits 4
octcib5 at simplebus0: max-bits 11
octcib6 at simplebus0: max-bits 11
cn30xxsmi0 at simplebus0
octxctl0 at simplebus0: DWC3 rev 0x250a
xhci0 at octxctl0, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev
3.00/1.00 addr 1
octxctl1 at simplebus0: DWC3 rev 0x250a
xhci1 at octxctl1, xHCI 1.0
usb1 at xhci1: USB revision 3.0
uhub1 at usb1 configuration 1 interface 0 "Generic xHCI root hub" rev
3.00/1.00 addr 1
com0 at simplebus0: ns16550a, 64 byte fifo
com0: console
com1 at simplebus0: ns16550a, 64 byte fifo
com1: probed fifo depth: 0 bytes
octmmc0 at simplebus0
sdmmc0 at octmmc0: 8-bit, mmc high-speed
sdmmc1 at octmmc0: 8-bit, mmc high-speedpass out quick on $wlan_vif inet proto 
udp from $fritzbox_wan to 192.168.133.0/24 rtable 1
octrng0 at iobus0 base 0x1400000000000 irq 0
cn30xxgmx0 at iobus0 base 0x1180008000000
cnmac0 at cn30xxgmx0: SGMII, address fc:ec:da:40:fa:42
ukphy0 at cnmac0 phy 4: Generic IEEE 802.3u media interface, rev. 2: OUI
0x0001c1, model 0x000c
cnmac1 at cn30xxgmx0: SGMII, address fc:ec:da:40:fa:43
ukphy1 at cnmac1 phy 5: Generic IEEE 802.3u media interface, rev. 2: OUI
0x0001c1, model 0x000c
cnmac2 at cn30xxgmx0: SGMII, address fc:ec:da:40:fa:44
ukphy2 at cnmac2 phy 6: Generic IEEE 802.3u media interface, rev. 2: OUI
0x0001c1, model 0x000c
cnmac3 at cn30xxgmx0: SGMII, address fc:ec:da:40:fa:45
ukphy3 at cnmac3 phy 7: Generic IEEE 802.3u media interface, rev. 2: OUI
0x0001c1, model 0x000c
cn30xxgmx1 at iobus0 base 0x1180010000000
cnmac4 at cn30xxgmx1: SGMII, address fc:ec:da:40:fa:46
ukphy4 at cnmac4 phy 8: Generic IEEE 802.3u media interface, rev. 0: OUI
0x0001c1, model 0x0027
cnmac5 at cn30xxgmx1: SGMII, address fc:ec:da:40:fa:47
ukphy5 at cnmac5 phy 9: Generic IEEE 802.3u media interface, rev. 0: OUI
0x0001c1, model 0x0027
/dev/ksyms: Symbol table not valid.
umass0 at uhub0 port 2 configuration 1 interface 0 "Generic USB3.0 Card
Reader" rev 3.00/15.32 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Generic, STORAGE DEVICE, 1532> SCSI4 0/direct
removable serial.05e30749000000001532
sd0: 61056MB, 512 bytes/sector, 125042688 sectors
sdmmc1: can't enable card
scsibus1 at sdmmc0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <Sandisk, SEM04G, 0000> SCSI2 0/direct
removable
sd1: 3776MB, 512 bytes/sector, 7733248 sectors
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
boot device: sd0
root on sd0a (1e8c6ddb499f7a0a.a) swap on sd0b dump on sd0b
WARNING: No TOD clock, believing file system.
WARNING: CHECK AND RESET THE DATE!

Automatic boot in progress: starting file system checks.
/dev/sd0a (1e8c6ddb499f7a0a.a): file system is clean; not checking
/dev/sd0l (1e8c6ddb499f7a0a.l): file system is clean; not checking
/dev/sd0d (1e8c6ddb499f7a0a.d): file system is clean; not checking
/dev/sd0f (1e8c6ddb499f7a0a.f): file system is clean; not checking
/dev/sd0g (1e8c6ddb499f7a0a.g): file system is clean; not checking
/dev/sd0h (1e8c6ddb499f7a0a.h): file system is clean; not checking
/dev/sd0k (1e8c6ddb499f7a0a.k): file system is clean; not checking
/dev/sd0j (1e8c6ddb499f7a0a.j): file system is clean; not checking
/dev/sd0e (1e8c6ddb499f7a0a.e): file system is clean; not checking
setting tty flags
pf enabled
net.inet.ip.forwarding: 0 -> 1
net.inet6.ip6.forwarding: 0 -> 1
net.inet6.icmp6.nd6_debug: 0 -> 0
net.inet.ipcomp.enable: 0 -> 1
net.pipex.enable: 0 -> 1
net.inet.gre.allow: 0 -> 1
net.inet.ip.ifq.maxlen: 2048 -> 2048
net.inet6.ip6.ifq.maxlen: 2048 -> 4096
net.inet.gre.wccp: 0 -> 1
net.inet.udp.recvspace: 41600 -> 262144
net.inet.udp.sendspace: 9216 -> 262144
starting network
ifconfig: SIOCSIFRDOMAIN: File exists
ifconfig: SIOCSIFRDOMAIN: File exists
ifconfig: SIOCSIFRDOMAIN: File exists
add net default: gateway 127.0.0.1
add net default: gateway 127.0.0.1
add net default: gateway 127.0.0.1
reordering libraries: done.
starting early daemons: syslogd pflogd unbound ntpd.
starting RPC daemons:.
savecore: /bsd: kvm_read: version misread
checking quotas: done.
kvm_mkdb: can't open /dev/ksyms
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd dhcpd smtpd.
starting package daemons: siproxd dhcpd2(failed).
starting local daemons: cron.
Sun Jul  1 06:15:17 CEST 2018

Re: edgerouter 6 / rdomain at boot

Reply via email to