On 13 April 2018 at 11:05, jungle Boogie <jungleboog...@gmail.com> wrote:
>
> Thanks for the reply. I think I'm closer, but there still seems to be
> some gaps...
It's working now! I had taken a shortcut earlier. At the installer
prompt, I incorrectly selected upgrade to take a shortcut. Now
thinking about it, openBSD wasn't installed so it didn't know the
partition layout.
Thanks for the the assistance, Jonathan. Thanks for Peter and all the
developers of openBSD.
dmesg of openBSD installed and running (not sure if it's different
than what's above):
pine64# dmesg
OpenBSD 6.3-current (GENERIC.MP) #69: Thu Apr 12 14:11:59 MDT 2018
dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC.MP
real mem = 2021416960 (1927MB)
avail mem = 1927913472 (1838MB)
mainbus0 at root: SoPine with baseboard
cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
efi0 at mainbus0: UEFI 2.7
efi0: Das U-Boot rev 0x0
psci0 at mainbus0: PSCI 0.2
agtimer0 at mainbus0: tick rate 24000 KHz
simplebus0 at mainbus0: "soc"
syscon0 at simplebus0: "syscon"
sxiccmu0 at simplebus0
sxipio0 at simplebus0: 103 pins
ampintc0 at simplebus0 nirq 224, ncpu 4 ipi: 0, 1: "interrupt-controller"
sxiccmu1 at simplebus0
sxipio1 at simplebus0: 13 pins
sxirsb0 at simplebus0
axppmic0 at sxirsb0 addr 0x3a3: AXP803
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
ehci1 at simplebus0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
com0 at simplebus0: ns16550, no working fifo
com0: console
dwxe0 at simplebus0: address 02:ba:43:50:f0:a3
rgephy0 at dwxe0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
sxirtc0 at simplebus0
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
gpio7 at sxipio0: 32 pins
gpio8 at sxipio1: 32 pins
cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4
cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4
cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SL32G, 0080> SCSI2 0/direct removable
sd0: 30436MB, 512 bytes/sector, 62333952 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd0a (cada93f8e15fb69e.a) swap on sd0b dump on sd0b
