On 12/4/17 8:49 AM, Ivo Chutkin wrote:
> Hello list,
>
> When I read OpenBSD could run on EdgeRouter Lite, I give it a try (now
> with 6.2 current as of 28.11.2017).
> I expected closer performance to Alix, but ERL even do not respond on
> console in reasonable times, for example, it takes 10-15 sec to log in.
> After reboot, it takes about 5 min on "reordering libraries:" vs 30 sec
> on Alix.
>
> Is it what I should expect from ERL or I am doing something wrong here?
>
> Thanks for your input,
> Ivo
Get better USB Flash Drive!
Mine is:
sd0 at scsibus0 targ 1 lun 0: <SanDisk, Cruzer Fit, 1.27> SCSI4 0/direct
removable serial.07815571360927117103
When I simply ping the box to see how long the reboot is and include the
full reorder of library...
Well here it is:
64 bytes from 10.0.0.13: icmp_seq=21 ttl=255 time=0.404 ms
64 bytes from 10.0.0.13: icmp_seq=72 ttl=255 time=274.757 ms
See 51 lost ping at 1 per/sec, so 51 sec to be out of service to be back
online ready for processing again.
$ dmesg
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2017 OpenBSD. All rights reserved.
https://www.OpenBSD.org
OpenBSD 6.2 (GENERIC) #0: Wed Oct 4 04:56:39 UTC 2017
visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC
real mem = 536870912 (512MB)
avail mem = 524009472 (499MB)
mainbus0 at root
cpu0 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
cpu0: cache L1-I 32KB 4 way D 8KB 64 way, L2 128KB 8 way
clock0 at mainbus0: int 5
iobus0 at mainbus0
simplebus0 at iobus0: "soc"
octciu0 at simplebus0
cn30xxsmi0 at simplebus0
com0 at simplebus0: ns16550a, 64 byte fifo
com0: console
dwctwo0 at iobus0 base 0x1180068000000 irq 56
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Octeon DWC2 root hub" rev
2.00/1.00 addr 1
octrng0 at iobus0 base 0x1400000000000 irq 0
cn30xxgmx0 at iobus0 base 0x1180008000000
cnmac0 at cn30xxgmx0: RGMII, address 44:d9:e7:40:ac:f8
atphy0 at cnmac0 phy 7: AR8035 10/100/1000 PHY, rev. 2
cnmac1 at cn30xxgmx0: RGMII, address 44:d9:e7:40:ac:f9
atphy1 at cnmac1 phy 6: AR8035 10/100/1000 PHY, rev. 2
cnmac2 at cn30xxgmx0: RGMII, address 44:d9:e7:40:ac:fa
atphy2 at cnmac2 phy 5: AR8035 10/100/1000 PHY, rev. 2
/dev/ksyms: Symbol table not valid.
umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk Cruzer Fit"
rev 2.00/1.27 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SanDisk, Cruzer Fit, 1.27> SCSI4 0/direct
removable serial.07815571360927117103
sd0: 15267MB, 512 bytes/sector, 31266816 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (55072c2137c3a4e7.a) swap on sd0b dump on sd0b
WARNING: No TOD clock, believing file system.
WARNING: CHECK AND RESET THE DATE!
