Ok.
Can that be the issue?
I will try that when I got to work tomorrow.
Thanks :)
On Oct 11, 2017 6:09 PM, "Chris Cappuccio" <ch...@nmedia.net> wrote:
> A side note, you should turn on AHCI in your BIOS, not 'compatible' mode
>
> pciide0: using apic 2 int 19 for native-PCI interrupt
> wd0 at pciide0 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> wd0: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> wd1 at pciide0 channel 0 drive 1: <Verbatim SATA-III SSD>
> wd1: 16-sector PIO, LBA48, 244198MB, 500118192 sectors
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
> wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 6
> wd2 at pciide0 channel 1 drive 1: <WDC WD20EARX-00PASB0>
> wd2: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> wd2(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 6
>
>
> Roar Waagsb?? [kowalczyk13...@gmail.com] wrote:
> > After a little tip I send this mail again without pastebin links.
> >
> > Hi.
> >
> > Architecture is: amd64
> >
> > dmesg:
> >
> > emulation)
> > wsdisplay0: screen 1-5 added (std, vt100 emulation)
> > xhci0 at pci0 dev 20 function 0 "Intel 7 Series xHCI" rev 0x04: msi
> > usb0 at xhci0: USB revision 3.0
> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> > 3.00/1.00 addr 1
> > "Intel 7 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured
> > ehci0 at pci0 dev 26 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb1 at ehci0: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > azalia0 at pci0 dev 27 function 0 "Intel 7 Series HD Audio" rev 0x04: msi
> > azalia0: codecs: Realtek/0x0887, Intel/0x2806, using Realtek/0x0887
> > audio0 at azalia0
> > ppb1 at pci0 dev 28 function 0 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci2 at ppb1 bus 2
> > ppb2 at pci0 dev 28 function 4 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci3 at ppb2 bus 3
> > re0 at pci3 dev 0 function 0 "Realtek 8168" rev 0x09: RTL8168F/8111F
> > (0x4800), msi, address 60:a4:4c:ad:8a:41
> > rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
> > ppb3 at pci0 dev 28 function 5 "Intel 82801BA Hub-to-PCI" rev 0xc4: msi
> > pci4 at ppb3 bus 4
> > ppb4 at pci4 dev 0 function 0 "ASMedia ASM1083/1085 PCIE-PCI" rev 0x03
> > pci5 at ppb4 bus 5
> > ehci1 at pci0 dev 29 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb2 at ehci1: USB revision 2.0
> > uhub2 at usb2 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > pcib0 at pci0 dev 31 function 0 "Intel H77 LPC" rev 0x04
> > pciide0 at pci0 dev 31 function 2 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 configured to native-PCI, channel 1 configured to native-PCI
> > pciide0: using apic 2 int 19 for native-PCI interrupt
> > wd0 at pciide0 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd0: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd1 at pciide0 channel 0 drive 1: <Verbatim SATA-III SSD>
> > wd1: 16-sector PIO, LBA48, 244198MB, 500118192 sectors
> > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
> > wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 6
> > wd2 at pciide0 channel 1 drive 1: <WDC WD20EARX-00PASB0>
> > wd2: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd2(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 6
> > ichiic0 at pci0 dev 31 function 3 "Intel 7 Series SMBus" rev 0x04: apic
> 2 int 18
> > iic0 at ichiic0
> > iic0: addr 0x20 01=00 02=00 03=00 04=00 05=00 06=00 07=f6 08=f6 09=f6
> > 0a=f6 0b=22 0c=22 0d=88 0e=88 0f=00 10=00 11=98 12=fc 13=04 14=00
> > 15=00 16=1c 17=66 18=00 19=00 1a=00 1b=00 1c=00 1d=22 1e=88 1f=02
> > 20=00 21=00 22=05 23=59 24=00 25=00 26=55 27=09 28=bf 29=00 2a=f5
> > 2b=00 2c=01 2d=d0 2e=a0 2f=18 30=00 31=00 32=00 33=68 3e=db 46=00
> > 47=03 48=04 49=13 b2=20 b3=83 words 00=ff00 01=0000 02=0000 03=0000
> > 04=0000 05=0000 06=00f6 07=f6f6
> > spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-10600
> > spdmem1 at iic0 addr 0x51: 4GB DDR3 SDRAM PC3-10600
> > spdmem2 at iic0 addr 0x52: 4GB DDR3 SDRAM PC3-10600
> > spdmem3 at iic0 addr 0x53: 4GB DDR3 SDRAM PC3-10600
> > pciide1 at pci0 dev 31 function 5 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 wired to native-PCI, channel 1 wired to native-PCI
> > pciide1: using apic 2 int 19 for native-PCI interrupt
> > wd3 at pciide1 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd3: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd3(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
> > isa0 at pcib0
> > isadma0 at isa0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> > pckbd0 at pckbc0 (kbd slot)
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pcppi0 at isa0 port 0x61
> > spkr0 at pcppi0
> > vmm0 at mainbus0: VMX/EPT
> > error: [drm:pid0:cpt_set_fifo_underrun_reporting] *ERROR* uncleared
> > pch fifo underrun on pch transcoder A
> > error: [drm:pid0:intel_pch_fifo_underrun_irq_handler] *ERROR* PCH
> > transcoder A FIFO underrun
> > uhidev0 at uhub0 port 3 configuration 1 interface 0 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev0: iclass 3/1
> > ukbd0 at uhidev0: 8 variable keys, 6 key codes
> > wskbd1 at ukbd0 mux 1
> > wskbd1: connecting to wsdisplay0
> > uhidev1 at uhub0 port 3 configuration 1 interface 1 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev1: iclass 3/0, 2 report ids
> > uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
> > uhid1 at uhidev1 reportid 2: input=2, output=0, feature=0
> > uhub3 at uhub1 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > uhub4 at uhub2 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > vscsi0 at root
> > scsibus1 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus2 at softraid0: 256 targets
> > root on wd1a (d2e56583ccf86119.a) swap on wd1b dump on wd1b
> > WARNING: / was not properly unmounted
> > syncing disks... done
> > rebooti
> > OpenBSD 6.1-current (GENERIC.MP) #21: Sun Aug 20 00:07:53 MDT 2017
> > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> > real mem = 16835751936 (16055MB)
> > avail mem = 16318504960 <(631)%20850-4960> (15562MB)
> > mpath0 at root
> > scsibus0 at mpath0: 256 targets
> > mainbus0 at root
> > bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xe98f0 (107 entries)
> > bios0: vendor American Megatrends Inc. version "1001" date 02/04/2013
> > bios0: ASUSTeK COMPUTER INC. P8H77-V LE
> > acpi0 at bios0: rev 2
> > acpi0: sleep states S0 S3 S4 S5
> > acpi0: tables DSDT FACP APIC FPDT MCFG HPET SSDT SSDT SSDT BGRT DMAR
> > acpi0: wakeup devices UAR1(S4) P0P1(S4) PXSX(S4) RP01(S4) PXSX(S4)
> > RP02(S4) PXSX(S4) RP03(S4) PXSX(S4) RP04(S4) PXSX(S4) RP07(S4)
> > PXSX(S4) RP08(S4) PEGP(S4) PEG0(S4) [...]
> > acpitimer0 at acpi0: 3579545 Hz, 24 bits
> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.47 MHz
> > cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu0: 256KB 64b/line 8-way L2 cache
> > cpu0: TSC frequency 3400467800 Hz
> > cpu0: smt 0, core 0, package 0
> > mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
> > cpu0: apic clock running at 100MHz
> > cpu0: mwait min=64, max=64, C-substates=0.2.1.1, IBE
> > cpu1 at mainbus0: apid 2 (application processor)
> > cpu1: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.01 MHz
> > cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu1: 256KB 64b/line 8-way L2 cache
> > cpu1: smt 0, core 1, package 0
> > cpu2 at mainbus0: apid 4 (application processor)
> > cpu2: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.01 MHz
> > cpu2: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu2: 256KB 64b/line 8-way L2 cache
> > cpu2: smt 0, core 2, package 0
> > cpu3 at mainbus0: apid 6 (application processor)
> > cpu3: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.01 MHz
> > cpu3: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu3: 256KB 64b/line 8-way L2 cache
> > cpu3: smt 0, core 3, package 0
> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> > acpimcfg0 at acpi0 addr 0xf8000000, bus 0-63
> > acpihpet0 at acpi0: 14318179 Hz
> > acpiprt0 at acpi0: bus 0 (PCI0)
> > acpiprt1 at acpi0: bus -1 (P0P1)
> > acpiprt2 at acpi0: bus 2 (RP01)
> > acpiprt3 at acpi0: bus -1 (RP02)
> > acpiprt4 at acpi0: bus -1 (RP03)
> > acpiprt5 at acpi0: bus -1 (RP04)
> > acpiprt6 at acpi0: bus -1 (RP07)
> > acpiprt7 at acpi0: bus -1 (RP08)
> > acpiprt8 at acpi0: bus 1 (PEG0)
> > acpiprt9 at acpi0: bus -1 (PEG1)
> > acpiprt10 at acpi0: bus -1 (PEG2)
> > acpiprt11 at acpi0: bus -1 (PEG3)
> > acpiprt12 at acpi0: bus 3 (RP05)
> > acpiprt13 at acpi0: bus 4 (RP06)
> > acpiprt14 at acpi0: bus 5 (PXSX)
> > acpiec0 at acpi0: not present
> > acpicpu0 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu1 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu2 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu3 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpipwrres0 at acpi0: FN00, resource for FAN0
> > acpipwrres1 at acpi0: FN01, resource for FAN1
> > acpipwrres2 at acpi0: FN02, resource for FAN2
> > acpipwrres3 at acpi0: FN03, resource for FAN3
> > acpipwrres4 at acpi0: FN04, resource for FAN4
> > acpitz0 at acpi0: critical temperature is 106 degC
> > acpitz1 at acpi0: critical temperature is 106 degC
> > "INT3F0D" at acpi0 not configured
> > acpibtn0 at acpi0: PWRB
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C14" at acpi0 not configured
> > acpivideo0 at acpi0: GFX0
> > acpivout0 at acpivideo0: DD02
> > cpu0: Enhanced SpeedStep 3400 MHz: speeds: 3401, 3400, 3300, 3100,
> > 3000, 2900, 2800, 2600, 2500, 2400, 2200, 2100, 2000, 1900, 1700, 1600
> > MHz
> > pci0 at mainbus0 bus 0
> > pchb0 at pci0 dev 0 function 0 "Intel Core 3G Host" rev 0x09
> > ppb0 at pci0 dev 1 function 0 "Intel Core 3G PCIE" rev 0x09: msi
> > pci1 at ppb0 bus 1
> > inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics 2500" rev 0x09
> > drm0 at inteldrm0
> > inteldrm0: msi
> > inteldrm0: 1920x1080, 32bpp
> > wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
> > wsdisplay0: screen 1-5 added (std, vt100 emulation)
> > xhci0 at pci0 dev 20 function 0 "Intel 7 Series xHCI" rev 0x04: msi
> > usb0 at xhci0: USB revision 3.0
> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> > 3.00/1.00 addr 1
> > "Intel 7 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured
> > ehci0 at pci0 dev 26 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb1 at ehci0: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > azalia0 at pci0 dev 27 function 0 "Intel 7 Series HD Audio" rev 0x04: msi
> > azalia0: codecs: Realtek/0x0887, Intel/0x2806, using Realtek/0x0887
> > audio0 at azalia0
> > ppb1 at pci0 dev 28 function 0 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci2 at ppb1 bus 2
> > ppb2 at pci0 dev 28 function 4 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci3 at ppb2 bus 3
> > re0 at pci3 dev 0 function 0 "Realtek 8168" rev 0x09: RTL8168F/8111F
> > (0x4800), msi, address 60:a4:4c:ad:8a:41
> > rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
> > ppb3 at pci0 dev 28 function 5 "Intel 82801BA Hub-to-PCI" rev 0xc4: msi
> > pci4 at ppb3 bus 4
> > ppb4 at pci4 dev 0 function 0 "ASMedia ASM1083/1085 PCIE-PCI" rev 0x03
> > pci5 at ppb4 bus 5
> > ehci1 at pci0 dev 29 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb2 at ehci1: USB revision 2.0
> > uhub2 at usb2 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > pcib0 at pci0 dev 31 function 0 "Intel H77 LPC" rev 0x04
> > pciide0 at pci0 dev 31 function 2 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 configured to native-PCI, channel 1 configured to native-PCI
> > pciide0: using apic 2 int 19 for native-PCI interrupt
> > wd0 at pciide0 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd0: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd1 at pciide0 channel 0 drive 1: <Verbatim SATA-III SSD>
> > wd1: 16-sector PIO, LBA48, 244198MB, 500118192 sectors
> > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
> > wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 6
> > wd2 at pciide0 channel 1 drive 1: <WDC WD20EARX-00PASB0>
> > wd2: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd2(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 6
> > ichiic0 at pci0 dev 31 function 3 "Intel 7 Series SMBus" rev 0x04: apic
> 2 int 18
> > iic0 at ichiic0
> > iic0: addr 0x20 01=00 02=00 03=00 04=00 05=00 06=00 07=f6 08=f6 09=f6
> > 0a=f6 0b=22 0c=22 0d=88 0e=88 0f=00 10=00 11=98 12=fc 13=04 14=00
> > 15=00 16=1c 17=66 18=00 19=00 1a=00 1b=00 1c=00 1d=22 1e=88 1f=02
> > 20=00 21=00 22=05 23=57 24=00 25=00 26=55 27=09 28=bf 29=00 2a=f5
> > 2b=00 2c=01 2d=d0 2e=a0 2f=18 30=00 31=00 32=00 33=68 3e=db 46=00
> > 47=03 48=04 49=13 b2=20 b3=83 words 00=ff00 01=0000 02=0000 03=0000
> > 04=0000 05=0000 06=00f6 07=f6f6
> > spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-10600
> > spdmem1 at iic0 addr 0x51: 4GB DDR3 SDRAM PC3-10600
> > spdmem2 at iic0 addr 0x52: 4GB DDR3 SDRAM PC3-10600
> > spdmem3 at iic0 addr 0x53: 4GB DDR3 SDRAM PC3-10600
> > pciide1 at pci0 dev 31 function 5 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 wired to native-PCI, channel 1 wired to native-PCI
> > pciide1: using apic 2 int 19 for native-PCI interrupt
> > wd3 at pciide1 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd3: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd3(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
> > isa0 at pcib0
> > isadma0 at isa0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> > pckbd0 at pckbc0 (kbd slot)
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pcppi0 at isa0 port 0x61
> > spkr0 at pcppi0
> > vmm0 at mainbus0: VMX/EPT
> > error: [drm:pid0:cpt_set_fifo_underrun_reporting] *ERROR* uncleared
> > pch fifo underrun on pch transcoder A
> > error: [drm:pid0:intel_pch_fifo_underrun_irq_handler] *ERROR* PCH
> > transcoder A FIFO underrun
> > uhidev0 at uhub0 port 3 configuration 1 interface 0 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev0: iclass 3/1
> > ukbd0 at uhidev0: 8 variable keys, 6 key codes
> > wskbd1 at ukbd0 mux 1
> > wskbd1: connecting to wsdisplay0
> > uhidev1 at uhub0 port 3 configuration 1 interface 1 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev1: iclass 3/0, 2 report ids
> > uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
> > uhid1 at uhidev1 reportid 2: input=2, output=0, feature=0
> > uhub3 at uhub1 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > uhub4 at uhub2 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > vscsi0 at root
> > scsibus1 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus2 at softraid0: 256 targets
> > root on wd1a (d2e56583ccf86119.a) swap on wd1b dump on wd1b
> > syncing disks... done
> > rebooti
> > OpenBSD 6.2-current (RAMDISK_CD) #137: Mon Oct 9 23:07:20 MDT 2017
> > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
> > real mem = 16835751936 (16055MB)
> > avail mem = 16321761280 (15565MB)
> > mainbus0 at root
> > bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xe98f0 (107 entries)
> > bios0: vendor American Megatrends Inc. version "1001" date 02/04/2013
> > bios0: ASUSTeK COMPUTER INC. P8H77-V LE
> > acpi0 at bios0: rev 2
> > acpi0: tables DSDT FACP APIC FPDT MCFG HPET SSDT SSDT SSDT BGRT DMAR
> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.53 MHz
> > cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu0: 256KB 64b/line 8-way L2 cache
> > cpu0: apic clock running at 100MHz
> > cpu0: mwait min=64, max=64, C-substates=0.2.1.1, IBE
> > cpu at mainbus0: not configured
> > cpu at mainbus0: not configured
> > cpu at mainbus0: not configured
> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> > acpiprt0 at acpi0: bus 0 (PCI0)
> > acpiprt1 at acpi0: bus -1 (P0P1)
> > acpiprt2 at acpi0: bus 2 (RP01)
> > acpiprt3 at acpi0: bus -1 (RP02)
> > acpiprt4 at acpi0: bus -1 (RP03)
> > acpiprt5 at acpi0: bus -1 (RP04)
> > acpiprt6 at acpi0: bus -1 (RP07)
> > acpiprt7 at acpi0: bus -1 (RP08)
> > acpiprt8 at acpi0: bus 1 (PEG0)
> > acpiprt9 at acpi0: bus -1 (PEG1)
> > acpiprt10 at acpi0: bus -1 (PEG2)
> > acpiprt11 at acpi0: bus -1 (PEG3)
> > acpiprt12 at acpi0: bus 3 (RP05)
> > acpiprt13 at acpi0: bus 4 (RP06)
> > acpiprt14 at acpi0: bus 5 (PXSX)
> > acpiec0 at acpi0: not present
> > acpicpu at acpi0 not configured
> > acpipwrres at acpi0 not configured
> > acpipwrres at acpi0 not configured
> > acpipwrres at acpi0 not configured
> > acpipwrres at acpi0 not configured
> > acpipwrres at acpi0 not configured
> > acpitz at acpi0 not configured
> > acpitz at acpi0 not configured
> > "INT3F0D" at acpi0 not configured
> > "PNP0C0C" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C14" at acpi0 not configured
> > pci0 at mainbus0 bus 0
> > pchb0 at pci0 dev 0 function 0 "Intel Core 3G Host" rev 0x09
> > ppb0 at pci0 dev 1 function 0 "Intel Core 3G PCIE" rev 0x09: msi
> > pci1 at ppb0 bus 1
> > vga1 at pci0 dev 2 function 0 "Intel HD Graphics 2500" rev 0x09
> > wsdisplay1 at vga1 mux 1: console (80x25, vt100 emulation)
> > xhci0 at pci0 dev 20 function 0 "Intel 7 Series xHCI" rev 0x04: msi
> > usb0 at xhci0: USB revision 3.0
> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> > 3.00/1.00 addr 1
> > "Intel 7 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured
> > ehci0 at pci0 dev 26 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb1 at ehci0: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > "Intel 7 Series HD Audio" rev 0x04 at pci0 dev 27 function 0 not
> configured
> > ppb1 at pci0 dev 28 function 0 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci2 at ppb1 bus 2
> > ppb2 at pci0 dev 28 function 4 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci3 at ppb2 bus 3
> > re0 at pci3 dev 0 function 0 "Realtek 8168" rev 0x09: RTL8168F/8111F
> > (0x4800), msi, address 60:a4:4c:ad:8a:41
> > rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
> > ppb3 at pci0 dev 28 function 5 "Intel 82801BA Hub-to-PCI" rev 0xc4: msi
> > pci4 at ppb3 bus 4
> > ppb4 at pci4 dev 0 function 0 "ASMedia ASM1083/1085 PCIE-PCI" rev 0x03
> > pci5 at ppb4 bus 5
> > ehci1 at pci0 dev 29 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb2 at ehci1: USB revision 2.0
> > uhub2 at usb2 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > "Intel H77 LPC" rev 0x04 at pci0 dev 31 function 0 not configured
> > pciide0 at pci0 dev 31 function 2 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 configured to native-PCI, channel 1 configured to native-PCI
> > pciide0: using apic 2 int 19 for native-PCI interrupt
> > wd0 at pciide0 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd0: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd1 at pciide0 channel 0 drive 1: <Verbatim SATA-III SSD>
> > wd1: 16-sector PIO, LBA48, 244198MB, 500118192 sectors
> > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
> > wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 6
> > wd2 at pciide0 channel 1 drive 1: <WDC WD20EARX-00PASB0>
> > wd2: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd2(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 6
> > "Intel 7 Series SMBus" rev 0x04 at pci0 dev 31 function 3 not configured
> > pciide1 at pci0 dev 31 function 5 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 wired to native-PCI, channel 1 wired to native-PCI
> > pciide1: using apic 2 int 19 for native-PCI interrupt
> > wd3 at pciide1 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd3: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd3(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
> > isa0 at mainbus0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> > pckbd0 at pckbc0 (kbd slot)
> > wskbd0 at pckbd0: console keyboard, using wsdisplay1
> > uhidev0 at uhub0 port 3 configuration 1 interface 0 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev0: iclass 3/1
> > ukbd0 at uhidev0
> > wskbd1 at ukbd0 mux 1
> > wskbd1: connecting to wsdisplay1
> > uhidev1 at uhub0 port 3 configuration 1 interface 1 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev1: iclass 3/0, 2 report ids
> > uhid at uhidev1 reportid 1 not configured
> > uhid at uhidev1 reportid 2 not configured
> > uhub3 at uhub1 port 1 configuration 1 interface 0 "vendor 0x8087
> > product 0x0024" rev 2.00/0.00 addr 2
> > uhub4 at uhub2 port 1 configuration 1 interface 0 "vendor 0x8087
> > product 0x0024" rev 2.00/0.00 addr 2
> > softraid0 at root
> > scsibus0 at softraid0: 256 targets
> > root on rd0a swap on rd0b dump on rd0b
> > syncing disks...
> > OpenBSD 6.2-current (GENERIC.MP) #139: Mon Oct 9 23:03:03 MDT 2017
> > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> > real mem = 16835751936 (16055MB)
> > avail mem = 16318648320 <(631)%20864-8320> (15562MB)
> > mpath0 at root
> > scsibus0 at mpath0: 256 targets
> > mainbus0 at root
> > bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xe98f0 (107 entries)
> > bios0: vendor American Megatrends Inc. version "1001" date 02/04/2013
> > bios0: ASUSTeK COMPUTER INC. P8H77-V LE
> > acpi0 at bios0: rev 2
> > acpi0: sleep states S0 S3 S4 S5
> > acpi0: tables DSDT FACP APIC FPDT MCFG HPET SSDT SSDT SSDT BGRT DMAR
> > acpi0: wakeup devices UAR1(S4) P0P1(S4) PXSX(S4) RP01(S4) PXSX(S4)
> > RP02(S4) PXSX(S4) RP03(S4) PXSX(S4) RP04(S4) PXSX(S4) RP07(S4)
> > PXSX(S4) RP08(S4) PEGP(S4) PEG0(S4) [...]
> > acpitimer0 at acpi0: 3579545 Hz, 24 bits
> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.48 MHz
> > cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu0: 256KB 64b/line 8-way L2 cache
> > acpitimer0: recalibrated TSC frequency 3400008838 Hz
> > cpu0: smt 0, core 0, package 0
> > mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
> > cpu0: apic clock running at 99MHz
> > cpu0: mwait min=64, max=64, C-substates=0.2.1.1, IBE
> > cpu1 at mainbus0: apid 2 (application processor)
> > cpu1: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.00 MHz
> > cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu1: 256KB 64b/line 8-way L2 cache
> > cpu1: smt 0, core 1, package 0
> > cpu2 at mainbus0: apid 4 (application processor)
> > cpu2: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.00 MHz
> > cpu2: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu2: 256KB 64b/line 8-way L2 cache
> > cpu2: smt 0, core 2, package 0
> > cpu3 at mainbus0: apid 6 (application processor)
> > cpu3: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.00 MHz
> > cpu3: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu3: 256KB 64b/line 8-way L2 cache
> > cpu3: smt 0, core 3, package 0
> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> > acpimcfg0 at acpi0 addr 0xf8000000, bus 0-63
> > acpihpet0 at acpi0: 14318179 Hz
> > acpihpet0: recalibrated TSC frequency 3400020880 Hz
> > acpiprt0 at acpi0: bus 0 (PCI0)
> > acpiprt1 at acpi0: bus -1 (P0P1)
> > acpiprt2 at acpi0: bus 2 (RP01)
> > acpiprt3 at acpi0: bus -1 (RP02)
> > acpiprt4 at acpi0: bus -1 (RP03)
> > acpiprt5 at acpi0: bus -1 (RP04)
> > acpiprt6 at acpi0: bus -1 (RP07)
> > acpiprt7 at acpi0: bus -1 (RP08)
> > acpiprt8 at acpi0: bus 1 (PEG0)
> > acpiprt9 at acpi0: bus -1 (PEG1)
> > acpiprt10 at acpi0: bus -1 (PEG2)
> > acpiprt11 at acpi0: bus -1 (PEG3)
> > acpiprt12 at acpi0: bus 3 (RP05)
> > acpiprt13 at acpi0: bus 4 (RP06)
> > acpiprt14 at acpi0: bus 5 (PXSX)
> > acpiec0 at acpi0: not present
> > acpicpu0 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu1 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu2 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu3 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpipwrres0 at acpi0: FN00, resource for FAN0
> > acpipwrres1 at acpi0: FN01, resource for FAN1
> > acpipwrres2 at acpi0: FN02, resource for FAN2
> > acpipwrres3 at acpi0: FN03, resource for FAN3
> > acpipwrres4 at acpi0: FN04, resource for FAN4
> > acpitz0 at acpi0: critical temperature is 106 degC
> > acpitz1 at acpi0: critical temperature is 106 degC
> > "INT3F0D" at acpi0 not configured
> > acpibtn0 at acpi0: PWRB
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C14" at acpi0 not configured
> > acpivideo0 at acpi0: GFX0
> > acpivout0 at acpivideo0: DD02
> > cpu0: Enhanced SpeedStep 3400 MHz: speeds: 3401, 3400, 3300, 3100,
> > 3000, 2900, 2800, 2600, 2500, 2400, 2200, 2100, 2000, 1900, 1700, 1600
> > MHz
> > pci0 at mainbus0 bus 0
> > pchb0 at pci0 dev 0 function 0 "Intel Core 3G Host" rev 0x09
> > ppb0 at pci0 dev 1 function 0 "Intel Core 3G PCIE" rev 0x09: msi
> > pci1 at ppb0 bus 1
> > inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics 2500" rev 0x09
> > drm0 at inteldrm0
> > inteldrm0: msi
> > inteldrm0: 1920x1080, 32bpp
> > wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
> > wsdisplay0: screen 1-5 added (std, vt100 emulation)
> > xhci0 at pci0 dev 20 function 0 "Intel 7 Series xHCI" rev 0x04: msi
> > usb0 at xhci0: USB revision 3.0
> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> > 3.00/1.00 addr 1
> > "Intel 7 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured
> > ehci0 at pci0 dev 26 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb1 at ehci0: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > azalia0 at pci0 dev 27 function 0 "Intel 7 Series HD Audio" rev 0x04: msi
> > azalia0: codecs: Realtek/0x0887, Intel/0x2806, using Realtek/0x0887
> > audio0 at azalia0
> > ppb1 at pci0 dev 28 function 0 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci2 at ppb1 bus 2
> > ppb2 at pci0 dev 28 function 4 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci3 at ppb2 bus 3
> > re0 at pci3 dev 0 function 0 "Realtek 8168" rev 0x09: RTL8168F/8111F
> > (0x4800), msi, address 60:a4:4c:ad:8a:41
> > rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
> > ppb3 at pci0 dev 28 function 5 "Intel 82801BA Hub-to-PCI" rev 0xc4: msi
> > pci4 at ppb3 bus 4
> > ppb4 at pci4 dev 0 function 0 "ASMedia ASM1083/1085 PCIE-PCI" rev 0x03
> > pci5 at ppb4 bus 5
> > ehci1 at pci0 dev 29 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb2 at ehci1: USB revision 2.0
> > uhub2 at usb2 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > pcib0 at pci0 dev 31 function 0 "Intel H77 LPC" rev 0x04
> > pciide0 at pci0 dev 31 function 2 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 configured to native-PCI, channel 1 configured to native-PCI
> > pciide0: using apic 2 int 19 for native-PCI interrupt
> > wd0 at pciide0 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd0: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd1 at pciide0 channel 0 drive 1: <Verbatim SATA-III SSD>
> > wd1: 16-sector PIO, LBA48, 244198MB, 500118192 sectors
> > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
> > wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 6
> > wd2 at pciide0 channel 1 drive 1: <WDC WD20EARX-00PASB0>
> > wd2: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd2(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 6
> > ichiic0 at pci0 dev 31 function 3 "Intel 7 Series SMBus" rev 0x04: apic
> 2 int 18
> > iic0 at ichiic0
> > iic0: addr 0x20 01=00 02=00 03=00 04=00 05=00 06=00 07=f6 08=f6 09=f6
> > 0a=f6 0b=22 0c=22 0d=88 0e=88 0f=00 10=00 11=98 12=fc 13=04 14=00
> > 15=00 16=1d 17=66 18=00 19=00 1a=00 1b=00 1c=00 1d=22 1e=88 1f=02
> > 20=00 21=00 22=04 23=58 24=00 25=00 26=55 27=09 28=bf 29=00 2a=f5
> > 2b=00 2c=01 2d=d0 2e=a0 2f=18 30=00 31=00 32=00 33=68 3e=db 46=00
> > 47=03 48=04 49=13 b2=20 b3=83 words 00=ff00 01=0000 02=0000 03=0000
> > 04=0000 05=0000 06=00f6 07=f6f6
> > spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-10600
> > spdmem1 at iic0 addr 0x51: 4GB DDR3 SDRAM PC3-10600
> > spdmem2 at iic0 addr 0x52: 4GB DDR3 SDRAM PC3-10600
> > spdmem3 at iic0 addr 0x53: 4GB DDR3 SDRAM PC3-10600
> > pciide1 at pci0 dev 31 function 5 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 wired to native-PCI, channel 1 wired to native-PCI
> > pciide1: using apic 2 int 19 for native-PCI interrupt
> > wd3 at pciide1 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd3: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd3(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
> > isa0 at pcib0
> > isadma0 at isa0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> > pckbd0 at pckbc0 (kbd slot)
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pcppi0 at isa0 port 0x61
> > spkr0 at pcppi0
> > vmm0 at mainbus0: VMX/EPT
> > error: [drm:pid0:cpt_set_fifo_underrun_reporting] *ERROR* uncleared
> > pch fifo underrun on pch transcoder A
> > error: [drm:pid0:intel_pch_fifo_underrun_irq_handler] *ERROR* PCH
> > transcoder A FIFO underrun
> > uhidev0 at uhub0 port 3 configuration 1 interface 0 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev0: iclass 3/1
> > ukbd0 at uhidev0: 8 variable keys, 6 key codes
> > wskbd1 at ukbd0 mux 1
> > wskbd1: connecting to wsdisplay0
> > uhidev1 at uhub0 port 3 configuration 1 interface 1 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev1: iclass 3/0, 2 report ids
> > uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
> > uhid1 at uhidev1 reportid 2: input=2, output=0, feature=0
> > uhub3 at uhub1 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > uhub4 at uhub2 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > vscsi0 at root
> > scsibus1 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus2 at softraid0: 256 targets
> > root on wd1a (d2e56583ccf86119.a) swap on wd1b dump on wd1b
> > syncing disks... done
> > reboot
> > OpenBSD 6.2-current (GENERIC.MP) #139: Mon Oct 9 23:03:03 MDT 2017
> > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> > real mem = 16835751936 (16055MB)
> > avail mem = 16318648320 <(631)%20864-8320> (15562MB)
> > mpath0 at root
> > scsibus0 at mpath0: 256 targets
> > mainbus0 at root
> > bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xe98f0 (107 entries)
> > bios0: vendor American Megatrends Inc. version "1001" date 02/04/2013
> > bios0: ASUSTeK COMPUTER INC. P8H77-V LE
> > acpi0 at bios0: rev 2
> > acpi0: sleep states S0 S3 S4 S5
> > acpi0: tables DSDT FACP APIC FPDT MCFG HPET SSDT SSDT SSDT BGRT DMAR
> > acpi0: wakeup devices UAR1(S4) P0P1(S4) PXSX(S4) RP01(S4) PXSX(S4)
> > RP02(S4) PXSX(S4) RP03(S4) PXSX(S4) RP04(S4) PXSX(S4) RP07(S4)
> > PXSX(S4) RP08(S4) PEGP(S4) PEG0(S4) [...]
> > acpitimer0 at acpi0: 3579545 Hz, 24 bits
> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.41 MHz
> > cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu0: 256KB 64b/line 8-way L2 cache
> > acpitimer0: recalibrated TSC frequency 3400004199 Hz
> > cpu0: smt 0, core 0, package 0
> > mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
> > cpu0: apic clock running at 100MHz
> > cpu0: mwait min=64, max=64, C-substates=0.2.1.1, IBE
> > cpu1 at mainbus0: apid 2 (application processor)
> > cpu1: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.01 MHz
> > cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu1: 256KB 64b/line 8-way L2 cache
> > cpu1: smt 0, core 1, package 0
> > cpu2 at mainbus0: apid 4 (application processor)
> > cpu2: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.01 MHz
> > cpu2: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu2: 256KB 64b/line 8-way L2 cache
> > cpu2: smt 0, core 2, package 0
> > cpu3 at mainbus0: apid 6 (application processor)
> > cpu3: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.01 MHz
> > cpu3: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu3: 256KB 64b/line 8-way L2 cache
> > cpu3: smt 0, core 3, package 0
> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> > acpimcfg0 at acpi0 addr 0xf8000000, bus 0-63
> > acpihpet0 at acpi0: 14318179 Hz
> > acpihpet0: recalibrated TSC frequency 3400027400 Hz
> > acpiprt0 at acpi0: bus 0 (PCI0)
> > acpiprt1 at acpi0: bus -1 (P0P1)
> > acpiprt2 at acpi0: bus 2 (RP01)
> > acpiprt3 at acpi0: bus -1 (RP02)
> > acpiprt4 at acpi0: bus -1 (RP03)
> > acpiprt5 at acpi0: bus -1 (RP04)
> > acpiprt6 at acpi0: bus -1 (RP07)
> > acpiprt7 at acpi0: bus -1 (RP08)
> > acpiprt8 at acpi0: bus 1 (PEG0)
> > acpiprt9 at acpi0: bus -1 (PEG1)
> > acpiprt10 at acpi0: bus -1 (PEG2)
> > acpiprt11 at acpi0: bus -1 (PEG3)
> > acpiprt12 at acpi0: bus 3 (RP05)
> > acpiprt13 at acpi0: bus 4 (RP06)
> > acpiprt14 at acpi0: bus 5 (PXSX)
> > acpiec0 at acpi0: not present
> > acpicpu0 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu1 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu2 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu3 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpipwrres0 at acpi0: FN00, resource for FAN0
> > acpipwrres1 at acpi0: FN01, resource for FAN1
> > acpipwrres2 at acpi0: FN02, resource for FAN2
> > acpipwrres3 at acpi0: FN03, resource for FAN3
> > acpipwrres4 at acpi0: FN04, resource for FAN4
> > acpitz0 at acpi0: critical temperature is 106 degC
> > acpitz1 at acpi0: critical temperature is 106 degC
> > "INT3F0D" at acpi0 not configured
> > acpibtn0 at acpi0: PWRB
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C14" at acpi0 not configured
> > acpivideo0 at acpi0: GFX0
> > acpivout0 at acpivideo0: DD02
> > cpu0: Enhanced SpeedStep 3400 MHz: speeds: 3401, 3400, 3300, 3100,
> > 3000, 2900, 2800, 2600, 2500, 2400, 2200, 2100, 2000, 1900, 1700, 1600
> > MHz
> > pci0 at mainbus0 bus 0
> > pchb0 at pci0 dev 0 function 0 "Intel Core 3G Host" rev 0x09
> > ppb0 at pci0 dev 1 function 0 "Intel Core 3G PCIE" rev 0x09: msi
> > pci1 at ppb0 bus 1
> > inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics 2500" rev 0x09
> > drm0 at inteldrm0
> > inteldrm0: msi
> > inteldrm0: 1920x1080, 32bpp
> > wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
> > wsdisplay0: screen 1-5 added (std, vt100 emulation)
> > xhci0 at pci0 dev 20 function 0 "Intel 7 Series xHCI" rev 0x04: msi
> > usb0 at xhci0: USB revision 3.0
> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> > 3.00/1.00 addr 1
> > "Intel 7 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured
> > ehci0 at pci0 dev 26 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb1 at ehci0: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > azalia0 at pci0 dev 27 function 0 "Intel 7 Series HD Audio" rev 0x04: msi
> > azalia0: codecs: Realtek/0x0887, Intel/0x2806, using Realtek/0x0887
> > audio0 at azalia0
> > ppb1 at pci0 dev 28 function 0 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci2 at ppb1 bus 2
> > ppb2 at pci0 dev 28 function 4 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci3 at ppb2 bus 3
> > re0 at pci3 dev 0 function 0 "Realtek 8168" rev 0x09: RTL8168F/8111F
> > (0x4800), msi, address 60:a4:4c:ad:8a:41
> > rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
> > ppb3 at pci0 dev 28 function 5 "Intel 82801BA Hub-to-PCI" rev 0xc4: msi
> > pci4 at ppb3 bus 4
> > ppb4 at pci4 dev 0 function 0 "ASMedia ASM1083/1085 PCIE-PCI" rev 0x03
> > pci5 at ppb4 bus 5
> > ehci1 at pci0 dev 29 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb2 at ehci1: USB revision 2.0
> > uhub2 at usb2 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > pcib0 at pci0 dev 31 function 0 "Intel H77 LPC" rev 0x04
> > pciide0 at pci0 dev 31 function 2 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 configured to native-PCI, channel 1 configured to native-PCI
> > pciide0: using apic 2 int 19 for native-PCI interrupt
> > wd0 at pciide0 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd0: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd1 at pciide0 channel 0 drive 1: <Verbatim SATA-III SSD>
> > wd1: 16-sector PIO, LBA48, 244198MB, 500118192 sectors
> > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
> > wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 6
> > wd2 at pciide0 channel 1 drive 1: <WDC WD20EARX-00PASB0>
> > wd2: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd2(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 6
> > ichiic0 at pci0 dev 31 function 3 "Intel 7 Series SMBus" rev 0x04: apic
> 2 int 18
> > iic0 at ichiic0
> > iic0: addr 0x20 01=00 02=00 03=00 04=00 05=00 06=00 07=f6 08=f6 09=f6
> > 0a=f6 0b=22 0c=22 0d=88 0e=88 0f=00 10=00 11=98 12=fc 13=04 14=00
> > 15=00 16=1c 17=65 18=00 19=00 1a=00 1b=00 1c=00 1d=22 1e=88 1f=02
> > 20=00 21=00 22=03 23=57 24=00 25=00 26=55 27=09 28=bf 29=00 2a=f5
> > 2b=00 2c=01 2d=d0 2e=a0 2f=18 30=00 31=00 32=00 33=68 3e=db 46=00
> > 47=03 48=04 49=13 b2=20 b3=83 words 00=ff00 01=0000 02=0000 03=0000
> > 04=0000 05=0000 06=00f6 07=f6f6
> > spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-10600
> > spdmem1 at iic0 addr 0x51: 4GB DDR3 SDRAM PC3-10600
> > spdmem2 at iic0 addr 0x52: 4GB DDR3 SDRAM PC3-10600
> > spdmem3 at iic0 addr 0x53: 4GB DDR3 SDRAM PC3-10600
> > pciide1 at pci0 dev 31 function 5 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 wired to native-PCI, channel 1 wired to native-PCI
> > pciide1: using apic 2 int 19 for native-PCI interrupt
> > wd3 at pciide1 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd3: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd3(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
> > isa0 at pcib0
> > isadma0 at isa0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> > pckbd0 at pckbc0 (kbd slot)
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pcppi0 at isa0 port 0x61
> > spkr0 at pcppi0
> > vmm0 at mainbus0: VMX/EPT
> > error: [drm:pid0:cpt_set_fifo_underrun_reporting] *ERROR* uncleared
> > pch fifo underrun on pch transcoder A
> > error: [drm:pid0:intel_pch_fifo_underrun_irq_handler] *ERROR* PCH
> > transcoder A FIFO underrun
> > uhidev0 at uhub0 port 3 configuration 1 interface 0 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev0: iclass 3/1
> > ukbd0 at uhidev0: 8 variable keys, 6 key codes
> > wskbd1 at ukbd0 mux 1
> > wskbd1: connecting to wsdisplay0
> > uhidev1 at uhub0 port 3 configuration 1 interface 1 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev1: iclass 3/0, 2 report ids
> > uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
> > uhid1 at uhidev1 reportid 2: input=2, output=0, feature=0
> > uhub3 at uhub1 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > uhub4 at uhub2 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > vscsi0 at root
> > scsibus1 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus2 at softraid0: 256 targets
> > root on wd1a (d2e56583ccf86119.a) swap on wd1b dump on wd1b
> > syncing disks... done
> > reboot
> > OpenBSD 6.2-current (RAMDISK_CD) #138: Tue Oct 10 12:34:02 MDT 2017
> > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
> > real mem = 16835751936 (16055MB)
> > avail mem = 16321761280 (15565MB)
> > mainbus0 at root
> > bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xe98f0 (107 entries)
> > bios0: vendor American Megatrends Inc. version "1001" date 02/04/2013
> > bios0: ASUSTeK COMPUTER INC. P8H77-V LE
> > acpi0 at bios0: rev 2
> > acpi0: tables DSDT FACP APIC FPDT MCFG HPET SSDT SSDT SSDT BGRT DMAR
> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.44 MHz
> > cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu0: 256KB 64b/line 8-way L2 cache
> > cpu0: apic clock running at 100MHz
> > cpu0: mwait min=64, max=64, C-substates=0.2.1.1, IBE
> > cpu at mainbus0: not configured
> > cpu at mainbus0: not configured
> > cpu at mainbus0: not configured
> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> > acpiprt0 at acpi0: bus 0 (PCI0)
> > acpiprt1 at acpi0: bus -1 (P0P1)
> > acpiprt2 at acpi0: bus 2 (RP01)
> > acpiprt3 at acpi0: bus -1 (RP02)
> > acpiprt4 at acpi0: bus -1 (RP03)
> > acpiprt5 at acpi0: bus -1 (RP04)
> > acpiprt6 at acpi0: bus -1 (RP07)
> > acpiprt7 at acpi0: bus -1 (RP08)
> > acpiprt8 at acpi0: bus 1 (PEG0)
> > acpiprt9 at acpi0: bus -1 (PEG1)
> > acpiprt10 at acpi0: bus -1 (PEG2)
> > acpiprt11 at acpi0: bus -1 (PEG3)
> > acpiprt12 at acpi0: bus 3 (RP05)
> > acpiprt13 at acpi0: bus 4 (RP06)
> > acpiprt14 at acpi0: bus 5 (PXSX)
> > acpiec0 at acpi0: not present
> > acpicpu at acpi0 not configured
> > acpipwrres at acpi0 not configured
> > acpipwrres at acpi0 not configured
> > acpipwrres at acpi0 not configured
> > acpipwrres at acpi0 not configured
> > acpipwrres at acpi0 not configured
> > acpitz at acpi0 not configured
> > acpitz at acpi0 not configured
> > "INT3F0D" at acpi0 not configured
> > "PNP0C0C" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C14" at acpi0 not configured
> > pci0 at mainbus0 bus 0
> > pchb0 at pci0 dev 0 function 0 "Intel Core 3G Host" rev 0x09
> > ppb0 at pci0 dev 1 function 0 "Intel Core 3G PCIE" rev 0x09: msi
> > pci1 at ppb0 bus 1
> > vga1 at pci0 dev 2 function 0 "Intel HD Graphics 2500" rev 0x09
> > wsdisplay1 at vga1 mux 1: console (80x25, vt100 emulation)
> > xhci0 at pci0 dev 20 function 0 "Intel 7 Series xHCI" rev 0x04: msi
> > usb0 at xhci0: USB revision 3.0
> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> > 3.00/1.00 addr 1
> > "Intel 7 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured
> > ehci0 at pci0 dev 26 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb1 at ehci0: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > "Intel 7 Series HD Audio" rev 0x04 at pci0 dev 27 function 0 not
> configured
> > ppb1 at pci0 dev 28 function 0 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci2 at ppb1 bus 2
> > ppb2 at pci0 dev 28 function 4 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci3 at ppb2 bus 3
> > re0 at pci3 dev 0 function 0 "Realtek 8168" rev 0x09: RTL8168F/8111F
> > (0x4800), msi, address 60:a4:4c:ad:8a:41
> > rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
> > ppb3 at pci0 dev 28 function 5 "Intel 82801BA Hub-to-PCI" rev 0xc4: msi
> > pci4 at ppb3 bus 4
> > ppb4 at pci4 dev 0 function 0 "ASMedia ASM1083/1085 PCIE-PCI" rev 0x03
> > pci5 at ppb4 bus 5
> > ehci1 at pci0 dev 29 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb2 at ehci1: USB revision 2.0
> > uhub2 at usb2 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > "Intel H77 LPC" rev 0x04 at pci0 dev 31 function 0 not configured
> > pciide0 at pci0 dev 31 function 2 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 configured to native-PCI, channel 1 configured to native-PCI
> > pciide0: using apic 2 int 19 for native-PCI interrupt
> > wd0 at pciide0 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd0: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd1 at pciide0 channel 0 drive 1: <Verbatim SATA-III SSD>
> > wd1: 16-sector PIO, LBA48, 244198MB, 500118192 sectors
> > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
> > wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 6
> > wd2 at pciide0 channel 1 drive 1: <WDC WD20EARX-00PASB0>
> > wd2: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd2(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 6
> > "Intel 7 Series SMBus" rev 0x04 at pci0 dev 31 function 3 not configured
> > pciide1 at pci0 dev 31 function 5 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 wired to native-PCI, channel 1 wired to native-PCI
> > pciide1: using apic 2 int 19 for native-PCI interrupt
> > wd3 at pciide1 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd3: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd3(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
> > isa0 at mainbus0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> > pckbd0 at pckbc0 (kbd slot)
> > wskbd0 at pckbd0: console keyboard, using wsdisplay1
> > uhidev0 at uhub0 port 3 configuration 1 interface 0 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev0: iclass 3/1
> > ukbd0 at uhidev0
> > wskbd1 at ukbd0 mux 1
> > wskbd1: connecting to wsdisplay1
> > uhidev1 at uhub0 port 3 configuration 1 interface 1 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev1: iclass 3/0, 2 report ids
> > uhid at uhidev1 reportid 1 not configured
> > uhid at uhidev1 reportid 2 not configured
> > uhub3 at uhub1 port 1 configuration 1 interface 0 "vendor 0x8087
> > product 0x0024" rev 2.00/0.00 addr 2
> > uhub4 at uhub2 port 1 configuration 1 interface 0 "vendor 0x8087
> > product 0x0024" rev 2.00/0.00 addr 2
> > softraid0 at root
> > scsibus0 at softraid0: 256 targets
> > root on rd0a swap on rd0b dump on rd0b
> > syncing disks...
> > OpenBSD 6.2-current (GENERIC.MP) #140: Tue Oct 10 12:29:44 MDT 2017
> > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> > real mem = 16835751936 (16055MB)
> > avail mem = 16318656512 <(631)%20865-6512> (15562MB)
> > mpath0 at root
> > scsibus0 at mpath0: 256 targets
> > mainbus0 at root
> > bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xe98f0 (107 entries)
> > bios0: vendor American Megatrends Inc. version "1001" date 02/04/2013
> > bios0: ASUSTeK COMPUTER INC. P8H77-V LE
> > acpi0 at bios0: rev 2
> > acpi0: sleep states S0 S3 S4 S5
> > acpi0: tables DSDT FACP APIC FPDT MCFG HPET SSDT SSDT SSDT BGRT DMAR
> > acpi0: wakeup devices UAR1(S4) P0P1(S4) PXSX(S4) RP01(S4) PXSX(S4)
> > RP02(S4) PXSX(S4) RP03(S4) PXSX(S4) RP04(S4) PXSX(S4) RP07(S4)
> > PXSX(S4) RP08(S4) PEGP(S4) PEG0(S4) [...]
> > acpitimer0 at acpi0: 3579545 Hz, 24 bits
> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.45 MHz
> > cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu0: 256KB 64b/line 8-way L2 cache
> > acpitimer0: recalibrated TSC frequency 3400008118 Hz
> > cpu0: smt 0, core 0, package 0
> > mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
> > cpu0: apic clock running at 99MHz
> > cpu0: mwait min=64, max=64, C-substates=0.2.1.1, IBE
> > cpu1 at mainbus0: apid 2 (application processor)
> > cpu1: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.00 MHz
> > cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu1: 256KB 64b/line 8-way L2 cache
> > cpu1: smt 0, core 1, package 0
> > cpu2 at mainbus0: apid 4 (application processor)
> > cpu2: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.00 MHz
> > cpu2: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu2: 256KB 64b/line 8-way L2 cache
> > cpu2: smt 0, core 2, package 0
> > cpu3 at mainbus0: apid 6 (application processor)
> > cpu3: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.00 MHz
> > cpu3: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu3: 256KB 64b/line 8-way L2 cache
> > cpu3: smt 0, core 3, package 0
> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> > acpimcfg0 at acpi0 addr 0xf8000000, bus 0-63
> > acpihpet0 at acpi0: 14318179 Hz
> > acpihpet0: recalibrated TSC frequency 3400018000 Hz
> > acpiprt0 at acpi0: bus 0 (PCI0)
> > acpiprt1 at acpi0: bus -1 (P0P1)
> > acpiprt2 at acpi0: bus 2 (RP01)
> > acpiprt3 at acpi0: bus -1 (RP02)
> > acpiprt4 at acpi0: bus -1 (RP03)
> > acpiprt5 at acpi0: bus -1 (RP04)
> > acpiprt6 at acpi0: bus -1 (RP07)
> > acpiprt7 at acpi0: bus -1 (RP08)
> > acpiprt8 at acpi0: bus 1 (PEG0)
> > acpiprt9 at acpi0: bus -1 (PEG1)
> > acpiprt10 at acpi0: bus -1 (PEG2)
> > acpiprt11 at acpi0: bus -1 (PEG3)
> > acpiprt12 at acpi0: bus 3 (RP05)
> > acpiprt13 at acpi0: bus 4 (RP06)
> > acpiprt14 at acpi0: bus 5 (PXSX)
> > acpiec0 at acpi0: not present
> > acpicpu0 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu1 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu2 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu3 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpipwrres0 at acpi0: FN00, resource for FAN0
> > acpipwrres1 at acpi0: FN01, resource for FAN1
> > acpipwrres2 at acpi0: FN02, resource for FAN2
> > acpipwrres3 at acpi0: FN03, resource for FAN3
> > acpipwrres4 at acpi0: FN04, resource for FAN4
> > acpitz0 at acpi0: critical temperature is 106 degC
> > acpitz1 at acpi0: critical temperature is 106 degC
> > "INT3F0D" at acpi0 not configured
> > acpibtn0 at acpi0: PWRB
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C14" at acpi0 not configured
> > acpivideo0 at acpi0: GFX0
> > acpivout0 at acpivideo0: DD02
> > cpu0: Enhanced SpeedStep 3400 MHz: speeds: 3401, 3400, 3300, 3100,
> > 3000, 2900, 2800, 2600, 2500, 2400, 2200, 2100, 2000, 1900, 1700, 1600
> > MHz
> > pci0 at mainbus0 bus 0
> > pchb0 at pci0 dev 0 function 0 "Intel Core 3G Host" rev 0x09
> > ppb0 at pci0 dev 1 function 0 "Intel Core 3G PCIE" rev 0x09: msi
> > pci1 at ppb0 bus 1
> > inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics 2500" rev 0x09
> > drm0 at inteldrm0
> > inteldrm0: msi
> > inteldrm0: 1920x1080, 32bpp
> > wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
> > wsdisplay0: screen 1-5 added (std, vt100 emulation)
> > xhci0 at pci0 dev 20 function 0 "Intel 7 Series xHCI" rev 0x04: msi
> > usb0 at xhci0: USB revision 3.0
> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> > 3.00/1.00 addr 1
> > "Intel 7 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured
> > ehci0 at pci0 dev 26 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb1 at ehci0: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > azalia0 at pci0 dev 27 function 0 "Intel 7 Series HD Audio" rev 0x04: msi
> > azalia0: codecs: Realtek/0x0887, Intel/0x2806, using Realtek/0x0887
> > audio0 at azalia0
> > ppb1 at pci0 dev 28 function 0 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci2 at ppb1 bus 2
> > ppb2 at pci0 dev 28 function 4 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci3 at ppb2 bus 3
> > re0 at pci3 dev 0 function 0 "Realtek 8168" rev 0x09: RTL8168F/8111F
> > (0x4800), msi, address 60:a4:4c:ad:8a:41
> > rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
> > ppb3 at pci0 dev 28 function 5 "Intel 82801BA Hub-to-PCI" rev 0xc4: msi
> > pci4 at ppb3 bus 4
> > ppb4 at pci4 dev 0 function 0 "ASMedia ASM1083/1085 PCIE-PCI" rev 0x03
> > pci5 at ppb4 bus 5
> > ehci1 at pci0 dev 29 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb2 at ehci1: USB revision 2.0
> > uhub2 at usb2 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > pcib0 at pci0 dev 31 function 0 "Intel H77 LPC" rev 0x04
> > pciide0 at pci0 dev 31 function 2 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 configured to native-PCI, channel 1 configured to native-PCI
> > pciide0: using apic 2 int 19 for native-PCI interrupt
> > wd0 at pciide0 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd0: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd1 at pciide0 channel 0 drive 1: <Verbatim SATA-III SSD>
> > wd1: 16-sector PIO, LBA48, 244198MB, 500118192 sectors
> > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
> > wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 6
> > wd2 at pciide0 channel 1 drive 1: <WDC WD20EARX-00PASB0>
> > wd2: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd2(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 6
> > ichiic0 at pci0 dev 31 function 3 "Intel 7 Series SMBus" rev 0x04: apic
> 2 int 18
> > iic0 at ichiic0
> > iic0: addr 0x20 01=00 02=00 03=00 04=00 05=00 06=00 07=f6 08=f6 09=f6
> > 0a=f6 0b=22 0c=22 0d=88 0e=88 0f=00 10=00 11=98 12=fc 13=04 14=00
> > 15=00 16=1c 17=65 18=00 19=00 1a=00 1b=00 1c=00 1d=22 1e=88 1f=02
> > 20=00 21=00 22=03 23=57 24=00 25=00 26=55 27=09 28=bf 29=00 2a=f5
> > 2b=00 2c=01 2d=d0 2e=a0 2f=18 30=00 31=00 32=00 33=68 3e=db 46=00
> > 47=03 48=04 49=13 b2=20 b3=83 words 00=ff00 01=0000 02=0000 03=0000
> > 04=0000 05=0000 06=00f6 07=f6f6
> > spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-10600
> > spdmem1 at iic0 addr 0x51: 4GB DDR3 SDRAM PC3-10600
> > spdmem2 at iic0 addr 0x52: 4GB DDR3 SDRAM PC3-10600
> > spdmem3 at iic0 addr 0x53: 4GB DDR3 SDRAM PC3-10600
> > pciide1 at pci0 dev 31 function 5 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 wired to native-PCI, channel 1 wired to native-PCI
> > pciide1: using apic 2 int 19 for native-PCI interrupt
> > wd3 at pciide1 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd3: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd3(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
> > isa0 at pcib0
> > isadma0 at isa0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> > pckbd0 at pckbc0 (kbd slot)
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pcppi0 at isa0 port 0x61
> > spkr0 at pcppi0
> > vmm0 at mainbus0: VMX/EPT
> > error: [drm:pid0:cpt_set_fifo_underrun_reporting] *ERROR* uncleared
> > pch fifo underrun on pch transcoder A
> > error: [drm:pid0:intel_pch_fifo_underrun_irq_handler] *ERROR* PCH
> > transcoder A FIFO underrun
> > uhidev0 at uhub0 port 3 configuration 1 interface 0 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev0: iclass 3/1
> > ukbd0 at uhidev0: 8 variable keys, 6 key codes
> > wskbd1 at ukbd0 mux 1
> > wskbd1: connecting to wsdisplay0
> > uhidev1 at uhub0 port 3 configuration 1 interface 1 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev1: iclass 3/0, 2 report ids
> > uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
> > uhid1 at uhidev1 reportid 2: input=2, output=0, feature=0
> > uhub3 at uhub1 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > uhub4 at uhub2 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > vscsi0 at root
> > scsibus1 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus2 at softraid0: 256 targets
> > root on wd1a (d2e56583ccf86119.a) swap on wd1b dump on wd1b
> > syncing disks... done
> > rebooting...
> > OpenBSD 6.2-current (GENERIC.MP) #140: Tue Oct 10 12:29:44 MDT 2017
> > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> > real mem = 16835751936 (16055MB)
> > avail mem = 16318644224 <(631)%20864-4224> (15562MB)
> > mpath0 at root
> > scsibus0 at mpath0: 256 targets
> > mainbus0 at root
> > bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xe98f0 (107 entries)
> > bios0: vendor American Megatrends Inc. version "1001" date 02/04/2013
> > bios0: ASUSTeK COMPUTER INC. P8H77-V LE
> > acpi0 at bios0: rev 2
> > acpi0: sleep states S0 S3 S4 S5
> > acpi0: tables DSDT FACP APIC FPDT MCFG HPET SSDT SSDT SSDT BGRT DMAR
> > acpi0: wakeup devices UAR1(S4) P0P1(S4) PXSX(S4) RP01(S4) PXSX(S4)
> > RP02(S4) PXSX(S4) RP03(S4) PXSX(S4) RP04(S4) PXSX(S4) RP07(S4)
> > PXSX(S4) RP08(S4) PEGP(S4) PEG0(S4) [...]
> > acpitimer0 at acpi0: 3579545 Hz, 24 bits
> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.47 MHz
> > cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu0: 256KB 64b/line 8-way L2 cache
> > acpitimer0: recalibrated TSC frequency 3400014278 Hz
> > cpu0: smt 0, core 0, package 0
> > mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
> > cpu0: apic clock running at 99MHz
> > cpu0: mwait min=64, max=64, C-substates=0.2.1.1, IBE
> > cpu1 at mainbus0: apid 2 (application processor)
> > cpu1: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.00 MHz
> > cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu1: 256KB 64b/line 8-way L2 cache
> > cpu1: smt 0, core 1, package 0
> > cpu2 at mainbus0: apid 4 (application processor)
> > cpu2: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.00 MHz
> > cpu2: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu2: 256KB 64b/line 8-way L2 cache
> > cpu2: smt 0, core 2, package 0
> > cpu3 at mainbus0: apid 6 (application processor)
> > cpu3: Intel(R) Core(TM) i5-3570 CPU @ 3.40GHz, 3400.00 MHz
> > cpu3: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,
> PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,
> CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,
> AES,XSAVE,AVX,F16C,RDRAND,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,
> FSGSBASE,SMEP,ERMS,SENSOR,ARAT
> > cpu3: 256KB 64b/line 8-way L2 cache
> > cpu3: smt 0, core 3, package 0
> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> > acpimcfg0 at acpi0 addr 0xf8000000, bus 0-63
> > acpihpet0 at acpi0: 14318179 Hz
> > acpihpet0: recalibrated TSC frequency 3400021400 Hz
> > acpiprt0 at acpi0: bus 0 (PCI0)
> > acpiprt1 at acpi0: bus -1 (P0P1)
> > acpiprt2 at acpi0: bus 2 (RP01)
> > acpiprt3 at acpi0: bus -1 (RP02)
> > acpiprt4 at acpi0: bus -1 (RP03)
> > acpiprt5 at acpi0: bus -1 (RP04)
> > acpiprt6 at acpi0: bus -1 (RP07)
> > acpiprt7 at acpi0: bus -1 (RP08)
> > acpiprt8 at acpi0: bus 1 (PEG0)
> > acpiprt9 at acpi0: bus -1 (PEG1)
> > acpiprt10 at acpi0: bus -1 (PEG2)
> > acpiprt11 at acpi0: bus -1 (PEG3)
> > acpiprt12 at acpi0: bus 3 (RP05)
> > acpiprt13 at acpi0: bus 4 (RP06)
> > acpiprt14 at acpi0: bus 5 (PXSX)
> > acpiec0 at acpi0: not present
> > acpicpu0 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu1 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu2 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpicpu3 at acpi0: C3(350@80 mwait.1@0x20), C2(500@59 mwait.1@0x10),
> > C1(1000@1 mwait.1), PSS
> > acpipwrres0 at acpi0: FN00, resource for FAN0
> > acpipwrres1 at acpi0: FN01, resource for FAN1
> > acpipwrres2 at acpi0: FN02, resource for FAN2
> > acpipwrres3 at acpi0: FN03, resource for FAN3
> > acpipwrres4 at acpi0: FN04, resource for FAN4
> > acpitz0 at acpi0: critical temperature is 106 degC
> > acpitz1 at acpi0: critical temperature is 106 degC
> > "INT3F0D" at acpi0 not configured
> > acpibtn0 at acpi0: PWRB
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C0B" at acpi0 not configured
> > "PNP0C14" at acpi0 not configured
> > acpivideo0 at acpi0: GFX0
> > acpivout0 at acpivideo0: DD02
> > cpu0: Enhanced SpeedStep 3400 MHz: speeds: 3401, 3400, 3300, 3100,
> > 3000, 2900, 2800, 2600, 2500, 2400, 2200, 2100, 2000, 1900, 1700, 1600
> > MHz
> > pci0 at mainbus0 bus 0
> > pchb0 at pci0 dev 0 function 0 "Intel Core 3G Host" rev 0x09
> > ppb0 at pci0 dev 1 function 0 "Intel Core 3G PCIE" rev 0x09: msi
> > pci1 at ppb0 bus 1
> > inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics 2500" rev 0x09
> > drm0 at inteldrm0
> > inteldrm0: msi
> > inteldrm0: 1920x1080, 32bpp
> > wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
> > wsdisplay0: screen 1-5 added (std, vt100 emulation)
> > xhci0 at pci0 dev 20 function 0 "Intel 7 Series xHCI" rev 0x04: msi
> > usb0 at xhci0: USB revision 3.0
> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
> > 3.00/1.00 addr 1
> > "Intel 7 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured
> > ehci0 at pci0 dev 26 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb1 at ehci0: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > azalia0 at pci0 dev 27 function 0 "Intel 7 Series HD Audio" rev 0x04: msi
> > azalia0: codecs: Realtek/0x0887, Intel/0x2806, using Realtek/0x0887
> > audio0 at azalia0
> > ppb1 at pci0 dev 28 function 0 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci2 at ppb1 bus 2
> > ppb2 at pci0 dev 28 function 4 "Intel 7 Series PCIE" rev 0xc4: msi
> > pci3 at ppb2 bus 3
> > re0 at pci3 dev 0 function 0 "Realtek 8168" rev 0x09: RTL8168F/8111F
> > (0x4800), msi, address 60:a4:4c:ad:8a:41
> > rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
> > ppb3 at pci0 dev 28 function 5 "Intel 82801BA Hub-to-PCI" rev 0xc4: msi
> > pci4 at ppb3 bus 4
> > ppb4 at pci4 dev 0 function 0 "ASMedia ASM1083/1085 PCIE-PCI" rev 0x03
> > pci5 at ppb4 bus 5
> > ehci1 at pci0 dev 29 function 0 "Intel 7 Series USB" rev 0x04: apic 2
> int 23
> > usb2 at ehci1: USB revision 2.0
> > uhub2 at usb2 configuration 1 interface 0 "Intel EHCI root hub" rev
> > 2.00/1.00 addr 1
> > pcib0 at pci0 dev 31 function 0 "Intel H77 LPC" rev 0x04
> > pciide0 at pci0 dev 31 function 2 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 configured to native-PCI, channel 1 configured to native-PCI
> > pciide0: using apic 2 int 19 for native-PCI interrupt
> > wd0 at pciide0 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd0: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd1 at pciide0 channel 0 drive 1: <Verbatim SATA-III SSD>
> > wd1: 16-sector PIO, LBA48, 244198MB, 500118192 sectors
> > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
> > wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 6
> > wd2 at pciide0 channel 1 drive 1: <WDC WD20EARX-00PASB0>
> > wd2: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd2(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 6
> > ichiic0 at pci0 dev 31 function 3 "Intel 7 Series SMBus" rev 0x04: apic
> 2 int 18
> > iic0 at ichiic0
> > iic0: addr 0x20 01=00 02=00 03=00 04=00 05=00 06=00 07=f6 08=f6 09=f6
> > 0a=f6 0b=22 0c=22 0d=88 0e=88 0f=00 10=00 11=98 12=fc 13=04 14=00
> > 15=00 16=1c 17=65 18=00 19=00 1a=00 1b=00 1c=00 1d=22 1e=88 1f=02
> > 20=00 21=00 22=03 23=56 24=00 25=00 26=55 27=09 28=bf 29=00 2a=f5
> > 2b=00 2c=01 2d=d0 2e=a0 2f=18 30=00 31=00 32=00 33=68 3e=db 46=00
> > 47=03 48=04 49=13 b2=20 b3=83 words 00=ff00 01=0000 02=0000 03=0000
> > 04=0000 05=0000 06=00f6 07=f6f6
> > spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-10600
> > spdmem1 at iic0 addr 0x51: 4GB DDR3 SDRAM PC3-10600
> > spdmem2 at iic0 addr 0x52: 4GB DDR3 SDRAM PC3-10600
> > spdmem3 at iic0 addr 0x53: 4GB DDR3 SDRAM PC3-10600
> > pciide1 at pci0 dev 31 function 5 "Intel 7 Series SATA" rev 0x04: DMA,
> > channel 0 wired to native-PCI, channel 1 wired to native-PCI
> > pciide1: using apic 2 int 19 for native-PCI interrupt
> > wd3 at pciide1 channel 0 drive 0: <WDC WD20EARX-00PASB0>
> > wd3: 16-sector PIO, LBA48, 1907729MB, 3907029168 sectors
> > wd3(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
> > isa0 at pcib0
> > isadma0 at isa0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> > pckbd0 at pckbc0 (kbd slot)
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pcppi0 at isa0 port 0x61
> > spkr0 at pcppi0
> > vmm0 at mainbus0: VMX/EPT
> > error: [drm:pid0:cpt_set_fifo_underrun_reporting] *ERROR* uncleared
> > pch fifo underrun on pch transcoder A
> > error: [drm:pid0:intel_pch_fifo_underrun_irq_handler] *ERROR* PCH
> > transcoder A FIFO underrun
> > uhidev0 at uhub0 port 3 configuration 1 interface 0 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev0: iclass 3/1
> > ukbd0 at uhidev0: 8 variable keys, 6 key codes
> > wskbd1 at ukbd0 mux 1
> > wskbd1: connecting to wsdisplay0
> > uhidev1 at uhub0 port 3 configuration 1 interface 1 "Chicony HP Elite
> > USB Keyboard" rev 1.10/1.21 addr 2
> > uhidev1: iclass 3/0, 2 report ids
> > uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
> > uhid1 at uhidev1 reportid 2: input=2, output=0, feature=0
> > uhub3 at uhub1 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > uhub4 at uhub2 port 1 configuration 1 interface 0 "Intel Rate Matching
> > Hub" rev 2.00/0.00 addr 2
> > vscsi0 at root
> > scsibus1 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus2 at softraid0: 256 targets
> > root on wd1a (d2e56583ccf86119.a) swap on wd1b dump on wd1b
> >
> >
> > My scripts for starting my vms:
> > 1st vm:
> > doas vmctl start "minecraft" -m 4G -n "uplink" -d
> > /mnt/disk1/vmm/minecraft/disk.img -d /mnt/disk1/vmm/minecraft/disk2.img
> > #doas vmctl start "minecraft" -c -b ~/upgrade/bsd.rd -m 4G -n "uplink" -d
> > /mnt/disk1/vmm/minecraft/disk.img -d /mnt/disk1/vmm/minecraft/disk2.img
> >
> > 2nd vm:
> > doas vmctl start "marianne" -m 2G -n "uplink" -d
> > /mnt/disk1/vmm/marianne/disk.img
> > #doas vmctl start "marianne" -c -b ~/upgrade/bsd.rd -m 2G -n "uplink" -d
> > /mnt/disk1/vmm/marianne/disk.img
> >
> > Vm.conf:
> > switch "uplink" {
> > add re0
> > }
> >
> >
> > Hostname.bridge0:
> >
> > add re0
> > add vether0
> > up
> > fwddelay 4
> >
> > !sleep 2
> >
> > !dhclient vether0
> >
> > ----
> > I run openbsd as guest vms on both
> >
> > I have 2 vms.
> >
> > I started vmd with -dvvv now and it gave me this error a little while
> after
> > starting my vm:
> > vmd_dispatch_vmm: handling TERMINATE_EVENT for vm id 1
> >
> >
> >
> > 2017-10-10 21:11 GMT+02:00 Carlos Cardenas <cardena...@gmail.com>:
> >
> > > On 10/10/17 11:57, Roar Waagsb?? wrote:
> > > > Hi.
> > > >
> > > > Sorry.
> > > >
> > > > Its my first report.
> > > >
> > > > Im not even sure its a bug or if its me doing something wrong.
> > > >
> > > > The logs arent saying much either, besides the one line I posted.
> > > >
> > > > Roar
> > > >
> > > > On Oct 10, 2017 5:21 PM, "Mike Larkin" <mlar...@azathoth.net> wrote:
> > > >
> > > >> On Tue, Oct 10, 2017 at 02:39:05PM +0200, Roar Waagsb?? wrote:
> > > >>> Hi.
> > > >>>
> > > >>> I starting using openbsd a while back and I was told on
> > > #openbsd@freenode
> > > >>> that vmm was the way to go, and not use qemu.
> > > >>>
> > > >>> I want to use openbsd on my host machine.
> > > >>>
> > > >>> I setup two vms and it worked fine.
> > > >>>
> > > >>> After about a week I noticed that one of my vms was shutdown.
> > > >>>
> > > >>> I started it back up again and didnt give it much thought.
> > > >>>
> > > >>> After a few days my other vm was shut down.
> > > >>>
> > > >>> Then after a few days again both my vms was shutdown.
> > > >>>
> > > >>> Today I upgraded the host to a new -current snapshot (10/10/2017)
> > > >>>
> > > >>> And when I start my vm now, it says that it starts successfully,
> then
> > > >> after
> > > >>> a few seconds it is shutdown again.
> > > >>>
> > > >>> I started vmd with -d (tried -dv but it said that -v wasnt an
> options,
> > > >> even
> > > >>> though man vmd say so)
> > > >>>
> > > >>> And the only thing /var/log/daemon says was:
> > > >>>
> > > >>> vmd2: vm2 even trhead exited unexpectedly.
> > > >>>
> > > >>> Am I missing something?
> > > >>>
> > > >>> Or am I doing anything wrong?
> > > >>>
> > > >>> Regards Roar
> > > >>
> > > >> Your bug report is horrible.
> > > >>
> > > >> man sendbug
> > > >>
> > > >> -ml
> > > >>
> > >
> > > Roar,
> > >
> > > Let's start with this:
> > > * You said you are running -current (2017-10-10), which architecture
> > > (amd64 or i386)? A dmesg would be good.
> > > * What are your VM params (i.e. how did you start them)? Do you have a
> > > vm.conf file you can share?
> > > * What guest VMs are you running?
> > > * How many vmd's are you running? (asking because of the "vmd2: ...."
> > > line) There should be only one.
> > >
> > > If you are going to run vmd in the foreground, make sure no other vmd
> > > instances are running.
> > >
> > > I don't understand your comment about '-v' since not only is it
> present in
> > > the usage of vmd but also
> > > in the man page (man vmd).
> > >
> > > los@rollo:% doas vmd -h
> > > vmd: unknown option -- h
> > > usage: vmd [-dnv] [-D macro=value] [-f file]
> > >
> > > Either way, run vmd in the foreground with '-dvvv' as in:
> > > doas vmd -dvvv
> > >
> > > Once you're able to share all of that info then we can start the
> process
> > > of troubleshooting.
> > >
> > > +--+
> > > Carlos
> > >
>
