Seems to have been resolved with the July 4 snapshot:
syncing disks... done
System restart.
?
Looking for valid bootloader image....
Jumping to start of image at address 0xbfc80000
U-Boot 1.1.1 (UBNT Build ID: 4670715-gbd7e2d7) (Build time: May 27 2014 -
11:16:22)
BIST check passed.
UBNT_E100 r1:2, r2:18, f:4/71, serial #: 44D9E79F9DE3
MPR 13-00318-18
Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz data rate)
DRAM: 512 MB
Clearing DRAM....... done
Flash: 4 MB
Net: octeth0, octeth1, octeth2
USB: (port 0) scanning bus for devices... 1 USB Devices found
scanning bus for storage devices...
Device 0: Vendor: SanDisk Prod.: Cruzer Fit Rev: 1.00
Type: Removable Hard Disk
Capacity: 60576.0 MB = 59.1 GB (124059648 x 512)
0
(Re)start USB...
USB: (port 0) scanning bus for devices... 1 USB Devices found
scanning bus for storage devices...
Device 0: Vendor: SanDisk Prod.: Cruzer Fit Rev: 1.00
Type: Removable Hard Disk
Capacity: 60576.0 MB = 59.1 GB (124059648 x 512)
reading bsd
......
..........
.
.
.....
..
...
5638112 bytes read
argv[2]: coremask=0x3
ELF file is 64 bit
Allocating memory for ELF segment: addr: 0xffffffff81000000 (adjusted to:
0x1000000), size 0x5680d0
Allocated memory for ELF segment: addr: 0xffffffff81000000, size 0x5680d0
Processing PHDR 0
Loading 4d9998 bytes at ffffffff81000000
Clearing 8e738 bytes at ffffffff814d9998
## Loading Linux kernel with entry point: 0xffffffff81000000 ...
Bootloader: Done loading app on coremask: 0x3
bootmem desc 0x24108 version 3.0
avail phys mem 0x00000000001004d0 - 0x0000000000fffcd0
avail phys mem 0x00000000015680d0 - 0x0000000008100000
avail phys mem 0x0000000008100010 - 0x000000000fffdc00
avail phys mem 0x0000000410000000 - 0x000000041ff00000
Total DRAM Size 0x0000000020000000
mem_layout[0] page 0x0000000000000041 -> 0x00000000000003FF
mem_layout[1] page 0x000000000000055B -> 0x0000000000002040
mem_layout[2] page 0x0000000000002041 -> 0x0000000000003FFF
mem_layout[3] page 0x0000000000104000 -> 0x0000000000107FC0
boot_desc->argv[0] = bootoctlinux
boot_dInitial setup done, switching console.
boot_desc->desc_ver:7
boot_desc->desc_size:400
boot_desc->stack_top:0
boot_desc->heap_start:0
boot_desc->heap_end:0
boot_desc->argc:3
boot_desc->flags:0x5
boot_desc->core_mask:0x3
boot_desc->dram_size:512
boot_desc->phy_mem_desc_addr:0
boot_desc->debugger_flag_addr:0xa44
boot_desc->eclock:500000000
boot_desc->boot_info_addr:0x100200
boot_info->ver_major:1
boot_info->ver_minor:2
boot_info->stack_top:0
boot_info->heap_start:0
boot_info->heap_end:0
boot_info->boot_desc_addr:0
boot_info->exception_base_addr:0x1000
boot_info->stack_size:0
boot_info->flags:0x5
boot_info->core_mask:0x3
boot_info->dram_size:512
boot_info->phys_mem_desc_addr:0x24108
boot_info->debugger_flags_addr:0
boot_info->eclock:500000000
boot_info->dclock:266000000
boot_info->board_type:20002
boot_info->board_rev_major:2
boot_info->board_rev_minor:18
boot_info->mac_addr_count:3
boot_info->cf_common_addr:0
boot_info->cf_attr_addr:0
boot_info->led_display_addr:0
boot_info->dfaclock:0
boot_info->config_flags:0x8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2017 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 6.1-current (GENERIC.MP) #0: Tue Jul 4 19:47:30 UTC 2017
visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC.MP
real mem = 536870912 (512MB)
avail mem = 524009472 (499MB)
mainbus0 at root
cpu0 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
cpu0: cache L1-I 32KB 4 way D 8KB 64 way, L2 128KB 8 way
cpu1 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
cpu1: cache L1-I 32KB 4 way D 8KB 64 way, L2 128KB 8 way
clock0 at mainbus0: int 5
iobus0 at mainbus0
simplebus0 at iobus0: "soc"
octciu0 at simplebus0
cn30xxsmi0 at simplebus0
com0 at simplebus0: ns16550a, 64 byte fifo
com0: console
dwctwo0 at iobus0 base 0x1180068000000 irq 56
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Octeon DWC2 root hub" rev 2.00/1.00
addr 1
octrng0 at iobus0 base 0x1400000000000 irq 0
cn30xxgmx0 at iobus0 base 0x1180008000000
cnmac0 at cn30xxgmx0: RGMII, address 44:d9:e7:9f:9d:e3
atphy0 at cnmac0 phy 7: AR8035 10/100/1000 PHY, rev. 2
cnmac1 at cn30xxgmx0: RGMII, address 44:d9:e7:9f:9d:e4
atphy1 at cnmac1 phy 6: AR8035 10/100/1000 PHY, rev. 2
cnmac2 at cn30xxgmx0: RGMII, address 44:d9:e7:9f:9d:e5
atphy2 at cnmac2 phy 5: AR8035 10/100/1000 PHY, rev. 2
/dev/ksyms: Symbol table not valid.
umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk Cruzer Fit" rev
2.10/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SanDisk, Cruzer Fit, 1.00> SCSI4 0/direct
removable serial.07815571310827117253
sd0: 60576MB, 512 bytes/sector, 124059648 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (dfe4803dad5c2926.a) swap on sd0b dump on sd0b
WARNING: No TOD clock, believing file system.
WARNING: CHECK AND RESET THE DATE!
cpu1 launched
Automatic boot in progress: starting file system checks.
/dev/sd0a (dfe4803dad5c2926.a): file system is clean; not checking
/dev/sd0l (dfe4803dad5c2926.l): file system is clean; not checking
/dev/sd0d (dfe4803dad5c2926.d): file system is clean; not checking
/dev/sd0f (dfe4803dad5c2926.f): file system is clean; not checking
/dev/sd0g (dfe4803dad5c2926.g): file system is clean; not checking
/dev/sd0h (dfe4803dad5c2926.h): file system is clean; not checking
/dev/sd0k (dfe4803dad5c2926.k): file system is clean; not checking
/dev/sd0j (dfe4803dad5c2926.j): file system is clean; not checking
/dev/sd0e (dfe4803dad5c2926.e): file system is clean; not checking
setting tty flags
pf enabled
net.inet.ip.forwarding: 0 -> 1
net.inet.ip.mforwarding: 0 -> 1
net.inet6.ip6.forwarding: 0 -> 1
net.inet6.ip6.mforwarding: 0 -> 1
net.inet6.ip6.multipath: 0 -> 1
net.inet.tcp.ecn: 0 -> 1
net.inet.carp.preempt: 0 -> 1
net.inet.carp.log: 2 -> 3
starting network
carp: carp0 demoted group carp by 1 to 129 (carpdev)
carp: carp200 demoted group carp by 1 to 130 (carpdev)
add net default: gateway 2001:470:39:4ab::1
carp: pfsync0 demoted group carp by 32 to 162 (pfsync init)
carp: pfsync0 demoted group pfsync by 32 to 32 (pfsync init)
carp: pfsync0 demoted group carp by 1 to 163 (pfsync bulk start)
carp: pfsync0 demoted group pfsync by 1 to 33 (pfsync bulk start)
reordering libraries:carp: carp0 demoted group carp by -1 to 162 (carpdev)
carp: carp200 demoted group carp by -1 to 161 (carpdev)
carp0: state transition: BACKUP -> MASTER
carp0: state transition: MASTER -> BACKUP
carp200: state transition: BACKUP -> MASTER
carp200: state transition: MASTER -> BACKUP
carp: pfsync0 demoted group carp by -1 to 160 (pfsync bulk done)
carp: pfsync0 demoted group pfsync by -1 to 32 (pfsync bulk done)
carp: pfsync0 demoted group carp by -32 to 128 (pfsync init)
carp: pfsync0 demoted group pfsync by -32 to 0 (pfsync init)
done.
starting early daemons: syslogd pflogd unbound ntpd.
starting RPC daemons:.
savecore: /bsd: kvm_read: version misread
checking quotas: done.
kvm_mkdb: can't open /dev/ksyms
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
---- /etc/mail/aliases unhandled, re-run sysmerge to merge the new version
---- /etc/mail/smtpd.conf unhandled, re-run sysmerge to merge the new version
---- /etc/ntpd.conf unhandled, re-run sysmerge to merge the new version
---- /etc/pf.conf unhandled, re-run sysmerge to merge the new version
---- /etc/ssh/sshd_config unhandled, re-run sysmerge to merge the new version
---- /var/unbound/etc/unbound.conf unhandled, re-run sysmerge to merge the new
version
starting network daemons: sshd dhcpd rtadvd smtpd sndiod.
Path to firmware: http://firmware.openbsd.org/firmware/snapshots/
No devices found which need firmware files to be downloaded.
starting package daemons: dkimproxy_out.
starting local daemons: cron.
Tue Jul 4 23:53:20 MDT 2017
OpenBSD/octeon (cody.iamnearl.com) (console)
login:
> On Jul 4, 2017, at 10:32 PM, Jan Kalkus <jkal...@gmail.com> wrote:
>
> I’m having a similar issue, but with the octeon build (on an Edgerouter Lite)
> and smtpd
>
> See ddb output below:
>
> ddb> dmesg
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2017 OpenBSD. All rights reserved. https://www.OpenBSD.org
>
> OpenBSD 6.1-current (GENERIC) #0: Mon Jul 3 19:57:33 UTC 2017
> visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC
> real mem = 536870912 (512MB)
> avail mem = 524107776 (499MB)
> mainbus0 at root
> cpu0 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
> cpu0: cache L1-I 32KB 4 way D 8KB 64 way, L2 128KB 8 way
> clock0 at mainbus0: int 5
> iobus0 at mainbus0
> simplebus0 at iobus0: "soc"
> octciu0 at simplebus0
> cn30xxsmi0 at simplebus0
> com0 at simplebus0: ns16550a, 64 byte fifo
> com0: console
> dwctwo0 at iobus0 base 0x1180068000000 irq 56
> usb0 at dwctwo0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Octeon DWC2 root hub" rev
> 2.00/1.00 a
> ddr 1
> octrng0 at iobus0 base 0x1400000000000 irq 0
> cn30xxgmx0 at iobus0 base 0x1180008000000
> cnmac0 at cn30xxgmx0: RGMII, address 44:d9:e7:9f:9d:e3
> atphy0 at cnmac0 phy 7: AR8035 10/100/1000 PHY, rev. 2
> cnmac1 at cn30xxgmx0: RGMII, address 44:d9:e7:9f:9d:e4
> atphy1 at cnmac1 phy 6: AR8035 10/100/1000 PHY, rev. 2
> cnmac2 at cn30xxgmx0: RGMII, address 44:d9:e7:9f:9d:e5
> atphy2 at cnmac2 phy 5: AR8035 10/100/1000 PHY, rev. 2
> /dev/ksyms: Symbol table not valid.
> umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk Cruzer Fit" rev
> 2.1
> 0/1.00 addr 2
> umass0: using SCSI over Bulk-Only
> scsibus0 at umass0: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <SanDisk, Cruzer Fit, 1.00> SCSI4 0/direct
> remova
> ble serial.07815571310827117253
> sd0: 60576MB, 512 bytes/sector, 124059648 sectors
> vscsi0 at root
> scsibus1 at vscsi0: 256 targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> boot device: sd0
> root on sd0a (dfe4803dad5c2926.a) swap on sd0b dump on sd0b
> WARNING: No TOD clock, believing file system.
> WARNING: CHECK AND RESET THE DATE!
> <3>carp: carp0 demoted group carp by 1 to 129 (carpdev)
> <3>carp: carp200 demoted group carp by 1 to 130 (carpdev)
> <3>carp: pfsync0 demoted group carp by 32 to 162 (pfsync init)
> <3>carp: pfsync0 demoted group pfsync by 32 to 32 (pfsync init)
> <3>carp: pfsync0 demoted group carp by 1 to 163 (pfsync bulk start)
> <3>carp: pfsync0 demoted group pfsync by 1 to 33 (pfsync bulk start)
> <3>carp: carp0 demoted group carp by -1 to 162 (carpdev)
> <3>carp: carp200 demoted group carp by -1 to 161 (carpdev)
> <2>carp0: state transition: BACKUP -> MASTER
> <2>carp200: state transition: BACKUP -> MASTER
> <2>carp0: state transition: MASTER -> BACKUP
> <2>carp200: state transition: MASTER -> BACKUP
> <3>carp: pfsync0 demoted group carp by -1 to 160 (pfsync bulk done)
> <3>carp: pfsync0 demoted group pfsync by -1 to 32 (pfsync bulk done)
> <3>carp: pfsync0 demoted group carp by -32 to 128 (pfsync init)
> <3>carp: pfsync0 demoted group pfsync by -32 to 0 (pfsync init)
> <2>carp0: state transition: BACKUP -> MASTER
> <2>carp200: state transition: BACKUP -> MASTER
> panic: rw_enter: netlock locking against myself
> Stopped at 0xffffffff811695d4: jr ra
> 0xffffffff811695d8: nop
> TID PID UID PRFLAGS PFLAGS CPU COMMAND
> * 92620 37730 95 0x100012 0 0 smtpd
> 0xffffffff811695d0 (49911817bfb27b93,9001070000000208,208,0) ra
> 0xffffffff810a
> 7e68 sp 0x9800000006e7fcd0, sz 0
> 0xffffffff810a7d10 (49911817bfb27b93,9001070000000208,208,0) ra 0x0 sp
> 0x98000
> 00006e7fcd0, sz 0
> User-level: pid 37730
> https://www.openbsd.org/ddb.html describes the minimum info required in bug
> reports. Insufficient info makes it difficult to find and fix bugs.
> ddb> 0xffffffff811695d0 (49911817bfb27b93,9001070000000208,208,0) ra
> 0xfffffff
> f810a7e68 sp 0x9800000006e7fcd0, sz 0
> 0xffffffff810a7d10 (49911817bfb27b93,9001070000000208,208,0) ra 0x0 sp
> 0x98000
> 00006e7fcd0, sz 0
> User-level: pid 37730
> ddb>
>
>
>> On Jul 4, 2017, at 7:58 PM, Rodrigo Mosconi <open...@mosconi.mat.br> wrote:
>>
>> Hi,
>>
>> I updated my notebook today to July 3 snapshot. And when the unbound
>> starts, the notebook has a kernel panic (hand copied):
>>
>> panic: rw_enter: netlock locking agains myself.
>>
>> I will upload the photos later and pass the links
>>
>> Follow dmesg:
>> OpenBSD 6.1-current (GENERIC) #75: Mon Jul 3 14:19:41 MDT 2017
>> dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC
>> real mem = 8227655680 (7846MB)
>> avail mem = 7972507648 (7603MB)
>> mpath0 at root
>> scsibus0 at mpath0: 256 targets
>> mainbus0 at root
>> bios0 at mainbus0: SMBIOS rev. 2.6 @ 0xe9b50 (51 entries)
>> bios0: vendor INSYDE version "V1.16" date 05/27/2011
>> bios0: Acer Aspire 4738
>> acpi0 at bios0: rev 2
>> acpi0: sleep states S0 S3 S4 S5
>> acpi0: tables DSDT FACP ASF! HPET APIC MCFG SLIC BOOT ASPT WDAT SSDT
>> acpi0: wakeup devices EHC1(S3) EHC2(S3) PXSX(S4) GLAN(S5) PXSX(S4) PXSX(S4)
>> PXSX(S4) PXSX(S4) PXSX(S4) PXSX(S4)
>> acpitimer0 at acpi0: 3579545 Hz, 24 bits
>> acpihpet0 at acpi0: 14318179 Hz
>> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
>> cpu0 at mainbus0: apid 0 (boot processor)
>> cpu0: Intel(R) Core(TM) i5 CPU M 480 @ 2.67GHz, 2660.47 MHz
>> cpu0:
>> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,POPCNT,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,SENSOR,ARAT
>> cpu0: 256KB 64b/line 8-way L2 cache
>> cpu0: TSC frequency 2660467900 Hz
>> cpu0: smt 0, core 0, package 0
>> mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
>> cpu0: apic clock running at 132MHz
>> cpu0: mwait min=64, max=64, C-substates=0.2.1.1, IBE
>> cpu at mainbus0: not configured
>> cpu at mainbus0: not configured
>> cpu at mainbus0: not configured
>> ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
>> acpimcfg0 at acpi0 addr 0xf0000000, bus 0-127
>> acpiprt0 at acpi0: bus 0 (PCI0)
>> acpiprt1 at acpi0: bus -1 (P0P2)
>> acpiprt2 at acpi0: bus 3 (P0P1)
>> acpiprt3 at acpi0: bus 1 (RP01)
>> acpiprt4 at acpi0: bus -1 (RP02)
>> acpiprt5 at acpi0: bus -1 (RP03)
>> acpiprt6 at acpi0: bus -1 (RP04)
>> acpiprt7 at acpi0: bus -1 (RP05)
>> acpiprt8 at acpi0: bus -1 (RP07)
>> acpiprt9 at acpi0: bus -1 (RP08)
>> acpiprt10 at acpi0: bus -1 (PEG3)
>> acpiprt11 at acpi0: bus -1 (PEG5)
>> acpiec0 at acpi0
>> acpicpu0 at acpi0: C3(350@245 mwait.3@0x20), C1(1000@3 mwait.1), PSS
>> acpitz0 at acpi0: critical temperature is 105 degC
>> "PNP0303" at acpi0 not configured
>> "SYN1B20" at acpi0 not configured
>> "PNP0C14" at acpi0 not configured
>> acpibat0 at acpi0: BAT1 model "AS10D51" serial 0A79 type LION oem
>> "PANASONIC"
>> acpiac0 at acpi0: AC unit online
>> acpibtn0 at acpi0: PWRB
>> acpibtn1 at acpi0: LID0
>> acpibtn2 at acpi0: SLPB
>> acpivideo0 at acpi0: GFX0
>> acpivout0 at acpivideo0: DD02
>> acpivideo1 at acpi0: VGA_
>> cpu0: Enhanced SpeedStep 2660 MHz: speeds: 2667, 2666, 2533, 2399, 2266,
>> 2133, 1999, 1866, 1733, 1599, 1466, 1333, 1199 MHz
>> pci0 at mainbus0 bus 0
>> pchb0 at pci0 dev 0 function 0 "Intel Core Host" rev 0x18
>> inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics" rev 0x18
>> drm0 at inteldrm0
>> intagp0 at inteldrm0
>> agp0 at intagp0: aperture at 0xc0000000, size 0x10000000
>> inteldrm0: msi
>> inteldrm0: 1366x768, 32bpp
>> wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
>> wsdisplay0: screen 1-5 added (std, vt100 emulation)
>> "Intel 3400 MEI" rev 0x06 at pci0 dev 22 function 0 not configured
>> ehci0 at pci0 dev 26 function 0 "Intel 3400 USB" rev 0x05: apic 2 int 16
>> usb0 at ehci0: USB revision 2.0
>> uhub0 at usb0 configuration 1 interface 0 "Intel EHCI root hub" rev
>> 2.00/1.00 addr 1
>> azalia0 at pci0 dev 27 function 0 "Intel 3400 HD Audio" rev 0x05: msi
>> azalia0: codecs: Realtek ALC272, Intel/0x2804, using Realtek ALC272
>> audio0 at azalia0
>> ppb0 at pci0 dev 28 function 0 "Intel 3400 PCIE" rev 0x05: msi
>> pci1 at ppb0 bus 1
>> bge0 at pci1 dev 0 function 0 "Broadcom BCM57780" rev 0x01, BCM57780 A1
>> (0x57780001): msi, address 60:eb:69:97:be:94
>> brgphy0 at bge0 phy 1: BCM57780 10/100/1000baseT PHY, rev. 1
>> ppb1 at pci0 dev 28 function 5 "Intel 3400 PCIE" rev 0x05: msi
>> pci2 at ppb1 bus 2
>> athn0 at pci2 dev 0 function 0 "Atheros AR9287" rev 0x01: apic 2 int 17
>> athn0: AR9287 rev 2 (2T2R), ROM rev 4, address 1c:65:9d:c2:b3:6b
>> ehci1 at pci0 dev 29 function 0 "Intel 3400 USB" rev 0x05: apic 2 int 23
>> usb1 at ehci1: USB revision 2.0
>> uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
>> 2.00/1.00 addr 1
>> ppb2 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xa5
>> pci3 at ppb2 bus 3
>> pcib0 at pci0 dev 31 function 0 "Intel HM55 LPC" rev 0x05
>> ahci0 at pci0 dev 31 function 2 "Intel 3400 AHCI" rev 0x05: msi, AHCI 1.3
>> ahci0: port 0: 3.0Gb/s
>> ahci0: port 1: 3.0Gb/s
>> scsibus1 at ahci0: 32 targets
>> sd0 at scsibus1 targ 0 lun 0: <ATA, WDC WDS120G1G0A-, Z331> SCSI3 0/direct
>> fixed naa.5001b444a665a76a
>> sd0: 114473MB, 512 bytes/sector, 234441648 sectors, thin
>> sd1 at scsibus1 targ 1 lun 0: <ATA, SanDisk SDSSDH12, 362A> SCSI3 0/direct
>> fixed naa.5000000647300648
>> sd1: 114473MB, 512 bytes/sector, 234441648 sectors, thin
>> ichiic0 at pci0 dev 31 function 3 "Intel 3400 SMBus" rev 0x05: apic 2 int 19
>> iic0 at ichiic0
>> spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-10600 SO-DIMM
>> spdmem1 at iic0 addr 0x52: 4GB DDR3 SDRAM PC3-10600 SO-DIMM
>> itherm0 at pci0 dev 31 function 6 "Intel 3400 Thermal" rev 0x05
>> isa0 at pcib0
>> isadma0 at isa0
>> pckbc0 at isa0 port 0x60/5 irq 1 irq 12
>> pckbd0 at pckbc0 (kbd slot)
>> wskbd0 at pckbd0: console keyboard, using wsdisplay0
>> pms0 at pckbc0 (aux slot)
>> wsmouse0 at pms0 mux 0
>> pms0: Synaptics touchpad, firmware 7.2
>> pcppi0 at isa0 port 0x61
>> spkr0 at pcppi0
>> pci4 at mainbus0 bus 127
>> pchb1 at pci4 dev 0 function 0 "Intel QuickPath" rev 0x05
>> pchb2 at pci4 dev 0 function 1 "Intel QuickPath" rev 0x05
>> pchb3 at pci4 dev 2 function 0 "Intel QPI Link" rev 0x05
>> pchb4 at pci4 dev 2 function 1 "Intel QPI Physical" rev 0x05
>> pchb5 at pci4 dev 2 function 2 "Intel Reserved" rev 0x05
>> pchb6 at pci4 dev 2 function 3 "Intel Reserved" rev 0x05
>> vmm0 at mainbus0: VMX/EPT
>> uhub2 at uhub0 port 1 configuration 1 interface 0 "Intel Rate Matching Hub"
>> rev 2.00/0.00 addr 2
>> uvideo0 at uhub2 port 1 configuration 1 interface 0 "A5ABR0S28 1.3M HD
>> WebCam" rev 2.00/0.11 addr 3
>> video0 at uvideo0
>> uhub3 at uhub1 port 1 configuration 1 interface 0 "Intel Rate Matching Hub"
>> rev 2.00/0.00 addr 2
>> vscsi0 at root
>> scsibus2 at vscsi0: 256 targets
>> softraid0 at root
>> scsibus3 at softraid0: 256 targets
>> softraid0: sd2 was not shutdown properly
>> sd2 at scsibus3 targ 1 lun 0: <OPENBSD, SR CRYPTO, 006> SCSI2 0/direct fixed
>> sd2: 114470MB, 512 bytes/sector, 234435953 sectors
>> root on sd2a (56e675278c069a9d.a) swap on sd2b dump on sd2b
>> WARNING: / was not properly unmounted
>
