All,
I've found a relatively cheap multi-disk chassis that connects using
e-SATA. Since my machine doesn't have e-SATA, I've ordered a simple
e-SATA card which is currently on backorder.
However, I realized my Cubox has an e-SATA port, so I tried connecting
it there, and it does get detected. However, with errors and the
disks that are in the chassis are not found:
imxahci0 at simplebus0: AHCI 1.3
imxahci0: port multiplier found: chip=38261095 rev=0x1706<PM1.1,PM1.0>
nports=6, features: 0x9<AsyncNotify,BIST>, enabled: 0x1<BIST>
imxahci0: device on port 0 didn't come ready, TFD: 0x50
imxahci0: port 0: 3.0Gb/s
scsibus0 at imxahci0: 32 targets
uk0 at scsibus0 targ 0 lun 0: <ATA, Port Multiplier, > SCSI3 30/unknown fixed
imxahci0.0: unable to clear PHY status
imxahci0.0: PMP port softreset cmd failed
imxahci0.0: unable to clear PHY status
imxahci0.0: PMP port softreset cmd failed
imxahci0.0: unable to probe PMP port due to softreset failure
imxahci0.1: unable to probe PMP port; portreset failed
imxahci0.2: unable to probe PMP port; portreset failed
imxahci0.3: unable to probe PMP port; portreset failed
imxahci0.4: unable to probe PMP port; portreset failed
imxahci0.5: unable to probe PMP port; portreset failed
I have no prior experience with port multipliers on OpenBSD, so I'm
not sure where the problem lies. Is this a limitation of imxahci?
Cheers,
Paul 'WEiRD' de Weerd
OpenBSD 6.1-current (GENERIC) #193: Sat Jul 1 03:40:04 MDT 2017
dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/GENERIC
real mem = 2147483648 (2048MB)
avail mem = 2097532928 (2000MB)
mainbus0 at root: SolidRun Cubox-i Dual/Quad
cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
simplebus0 at mainbus0: "soc"
ampintc0 at simplebus0 nirq 160, ncpu 4
simplebus1 at simplebus0: "aips-bus"
imxccm0 at simplebus1: imx6 rev 1.5 CPU freq: 792 MHz
imxiomuxc0 at simplebus1
simplebus2 at simplebus1: "spba-bus"
imxuart0 at simplebus2: console
imxgpio0 at simplebus1
imxgpio1 at simplebus1
imxgpio2 at simplebus1
imxgpio3 at simplebus1
imxgpio4 at simplebus1
imxgpio5 at simplebus1
imxgpio6 at simplebus1
imxdog0 at simplebus1
imxtemp0 at simplebus1
imxgpc0 at simplebus1
simplebus3 at simplebus0: "aips-bus"
imxehci0 at simplebus3
usb0 at imxehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "i.MX6 EHCI root hub" rev 2.00/1.00
addr 1
imxehci1 at simplebus3
usb1 at imxehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "i.MX6 EHCI root hub" rev 2.00/1.00
addr 1
fec0 at simplebus3
fec0: address d0:63:b4:00:3f:fb
atphy0 at fec0 phy 0: AR8035 10/100/1000 PHY, rev. 2
imxesdhc0 at simplebus3
imxesdhc0: 198 MHz base clock
sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma
imxesdhc1 at simplebus3
imxesdhc1: 198 MHz base clock
sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma
imxiic0 at simplebus3
iic0 at imxiic0
imxiic1 at simplebus3
iic1 at imxiic1
pcfrtc0 at iic1 addr 0x68: battery ok
imxocotp0 at simplebus3
imxuart1 at simplebus3
imxahci0 at simplebus0: AHCI 1.3
imxahci0: port multiplier found: chip=38261095 rev=0x1706<PM1.1,PM1.0>
nports=6, features: 0x9<AsyncNotify,BIST>, enabled: 0x1<BIST>
imxahci0: device on port 0 didn't come ready, TFD: 0x50
imxahci0: port 0: 3.0Gb/s
scsibus0 at imxahci0: 32 targets
uk0 at scsibus0 targ 0 lun 0: <ATA, Port Multiplier, > SCSI3 30/unknown fixed
imxahci0.0: unable to clear PHY status
imxahci0.0: PMP port softreset cmd failed
imxahci0.0: unable to clear PHY status
imxahci0.0: PMP port softreset cmd failed
imxahci0.0: unable to probe PMP port due to softreset failure
imxahci0.1: unable to probe PMP port; portreset failed
imxahci0.2: unable to probe PMP port; portreset failed
imxahci0.3: unable to probe PMP port; portreset failed
imxahci0.4: unable to probe PMP port; portreset failed
imxahci0.5: unable to probe PMP port; portreset failed
simplebus4 at mainbus0: "regulators"
scsibus1 at sdmmc1: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <Sandisk, SA16G, 0024> SCSI2 0/direct removable
sd0: 14772MB, 512 bytes/sector, 30253056 sectors
(manufacturer 0x2d0, product 0x4330)at sdmmc0 function 1 not configured
(manufacturer 0x2d0, product 0x4330)at sdmmc0 function 2 not configured
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
boot device: sd0
root on sd0a (fe2f3d685a24e68d.a) swap on sd0b dump on sd0b
--
>++++++++[<++++++++++>-]<+++++++.>+++[<------>-]<.>+++[<+
+++++++++++>-]<.>++[<------------>-]<+.--------------.[-]
http://www.weirdnet.nl/
