I updated an alix.3c3 box from OpenBSD 4.6 release to 6.0 release
recently via bsd.rd install kernel.
This went very smoothly, except that now I can't get a serial stream via
the DB9 serial connector.
On a linux box, I do indeed receive the (geiger data) lines like these
at a speed of 9600 baud:
#513302 Timestamp: 733348928 Delta_Timestamp: 60000 Total_Impulses:
39769137 Delta_Impulses: 90
so up to the connector at the end of the cable arriving from geiger
interface the data is coming, and in can be read and stored, etc.
But on that alix box, nothing seems to arrive at the serial line. I
tried all of these (the <x> were in 0 t o5):
# cu -d -l ttyC<x> -s
9600
Connected to /dev/ttyC<x> (speed 9600)
Result: no data at all arrives. I don't see what went wrong.
Peer
# dmesg
OpenBSD 6.0 (GENERIC) #1917: Tue Jul 26 12:48:33 MDT 2016
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD"
586-class) 499 MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
real mem = 259207168 (247MB)
avail mem = 241590272 (230MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: date 11/15/07, BIOS32 rev. 0 @ 0xfaf90
apm0 at bios0: Power Management spec V1.2 (slowidle)
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdfb4
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf20/144 (7 entries)
pcibios0: bad IRQ table checksum
pcibios0: PCI BIOS has 7 Interrupt Routing table entries
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: no compatible PCI ICU found
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0xa800 0xef000/0x1000!
cpu0 at mainbus0: (uniprocessor)
mtrr: K6-family MTRR support (2 registers)
amdmsr0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
vga1 at pci0 dev 1 function 1 "AMD Geode LX Video" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11,
address 00:0d:b9:13:3c:30
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 3,
32-bit 3579545Hz timer, watchdog, gpio, i2c
gpio0 at glxpcib0: 32 pins
iic0 at glxpcib0
maxtmp0 at iic0 addr 0x4c: lm86
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <TRANSCEND>
wd0: 1-sector PIO, LBA, 3823MB, 7831152 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
auglx0 at pci0 dev 15 function 3 "AMD CS5536 Audio" rev 0x01: irq 11,
CS5536 AC97
ac97: codec id 0x414c4770 (Avance Logic ALC203 rev 0)
ac97: codec features headphone, 20 bit DAC, 18 bit ADC, No 3D Stereo
audio0 at auglx0
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 5,
version 1.0, legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 5
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbdprobe: reset response 0xfa
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on wd0a (0e0478eff5b1b08d.a) swap on wd0b dump on wd0b
--
Peer Janssen - p...@pjk.de
