kwesterb...@gmail.com (Kenneth Westerback), 2014.03.19 (Wed) 17:09 (CET): > Alas, softraid only supports 512 byte block devices at the moment. > .... Ken
Any news on this one? No answer as always means 'no'. I saw plus58.html: * Use DEV_BSIZE instead of 512 where appropriate in the kernel. This starts laying the groundwork to allow disks with other sector sizes. Just asking because some time has gone by and krw@ thought it was a pitty [0]: [0] http://dictionary.reference.com/browse/alas used as an exclamation to express sorrow, grief, pity, concern, or apprehension of evil. Thanks+Bye, Marcus > On Mar 19, 2014 11:36 AM, "Marcus MERIGHI" <mcmer-open...@tor.at> wrote: > > > Reference: > > ``Softraid 3TB Problems'' > > http://marc.info/?l=openbsd-misc&m=136225193931620 > > > > Difference: > > My HDDs show up as 4096 bytes/sector in dmesg. > > > > Short: > > Are there any options for disks that come with 4096 bytes/sector to use > > with softraid(4)/bioctl(8)? > > > > Long: > > > > So I got these lovely large disks: > > > > DMESG (full one at the end): > > > > umass4 at uhub5 port 4 configuration 1 interface 0 "Intenso USB 3.0 > > Device" rev 2.10/1.00 addr 9 > > umass4: using SCSI over Bulk-Only > > scsibus5 at umass4: 2 targets, initiator 0 > > sd5 at scsibus5 targ 1 lun 0: <Intenso, USB 3.0 Device, 0> SCSI4 > > 0/direct fixed serial.174c55aa0000000022DF > > sd5: 2861588MB, 4096 bytes/sector, 732566646 sectors > > ^^^^ > > I suppose right above is my problem? > > > > FDISK: > > > > Disk: sd5 geometry: 45600/255/63 [732566646 4096-byte Sectors] > > Offset: 0 Signature: 0xAA55 > > Starting Ending LBA Info: > > #: id C H S - C H S [ start: size ] > > > > > ----------------------------------------------------------------------------- > -- > > 0: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > 1: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > 2: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > *3: A6 0 1 2 - 45599 254 63 [ 64: 732563936 ] > > OpenBSD > > > > DISKLABEL: > > > > # /dev/rsd5c: > > type: SCSI > > disk: SCSI disk > > label: whoknows > > duid: 470974d3647801b8 > > flags: > > bytes/sector: 4096 > > sectors/track: 63 > > tracks/cylinder: 255 > > sectors/cylinder: 16065 > > cylinders: 45600 > > total sectors: 732566646 > > boundstart: 64 > > boundend: 732564000 > > drivedata: 0 > > > > 16 partitions: > > # size offset fstype [fsize bsize cpg] > > a: 732563936 64 RAID > > c: 732566646 0 unused > > > > BIOCTL output > > > > $ sudo bioctl -h -v -c C -l /dev/sd3a softraid0 > > softraid0: sd3a has unsupported sector size (4096) > > softraid0: invalid metadata format > > > > Thanks in advance, Marcus > > > > DMESG FULL: > > This is -current with a patch from brad@ to get the NICs (re) working. > > > > OpenBSD 5.5-current (GENERIC.MP) #3: Tue Mar 11 14:18:33 CET 2014 > > r...@fofo.fifi.at:/usr/src/sys/arch/amd64/compile/GENERIC.MP > > real mem = 4161052672 (3968MB) > > avail mem = 4041580544 (3854MB) > > mainbus0 at root > > bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xeb530 (73 entries) > > bios0: vendor American Megatrends Inc. version "1.03" date 08/09/2013 > > bios0: Shuttle Inc. DS47D > > acpi0 at bios0: rev 2 > > acpi0: sleep states S0 S3 S4 S5 > > acpi0: tables DSDT FACP APIC FPDT MCFG SLIC HPET SSDT SSDT SSDT > > acpi0: wakeup devices P0P1(S4) USB1(S3) USB2(S3) USB3(S3) USB4(S3) > > USB5(S3) USB6(S3) USB7(S3) PXSX(S4) RP01(S4) PXSX(S4) RP02(S4) PXSX(S4) > > RP03(S4) PXSX(S4) RP04(S4) [...] > > acpitimer0 at acpi0: 3579545 Hz, 24 bits > > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat > > cpu0 at mainbus0: apid 0 (boot processor) > > cpu0: Intel(R) Celeron(R) CPU 847 @ 1.10GHz, 1097.67 MHz > > cpu0: > > > > > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS > H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX > ,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,XSAVE > ,NXE,LONG,LAHF,PERF,ITSC > > cpu0: 256KB 64b/line 8-way L2 cache > > cpu0: smt 0, core 0, package 0 > > mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges > > cpu0: apic clock running at 99MHz > > cpu0: mwait min=64, max=64, C-substates=0.2.1.1.2, IBE > > cpu1 at mainbus0: apid 2 (application processor) > > cpu1: Intel(R) Celeron(R) CPU 847 @ 1.10GHz, 1097.51 MHz > > cpu1: > > > > > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS > H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX > ,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,XSAVE > ,NXE,LONG,LAHF,PERF,ITSC > > cpu1: 256KB 64b/line 8-way L2 cache > > cpu1: smt 0, core 1, package 0 > > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins > > acpimcfg0 at acpi0 addr 0xf8000000, bus 0-63 > > acpihpet0 at acpi0: 14318179 Hz > > acpiprt0 at acpi0: bus 0 (PCI0) > > acpiprt1 at acpi0: bus -1 (P0P1) > > acpiprt2 at acpi0: bus 1 (RP01) > > acpiprt3 at acpi0: bus 2 (RP02) > > acpiprt4 at acpi0: bus 3 (RP03) > > acpiprt5 at acpi0: bus 4 (RP04) > > acpiprt6 at acpi0: bus -1 (RP05) > > acpiprt7 at acpi0: bus -1 (RP06) > > acpiprt8 at acpi0: bus -1 (RP07) > > acpiprt9 at acpi0: bus -1 (RP08) > > acpiprt10 at acpi0: bus -1 (PEG0) > > acpiprt11 at acpi0: bus -1 (PEG1) > > acpiprt12 at acpi0: bus -1 (PEG2) > > acpiprt13 at acpi0: bus -1 (PEG3) > > acpiec0 at acpi0: Failed to read resource settings > > acpicpu0 at acpi0: C1, PSS > > acpicpu1 at acpi0: C1, PSS > > acpipwrres0 at acpi0: FN00, resource for FAN0 > > acpipwrres1 at acpi0: FN01, resource for FAN1 > > acpipwrres2 at acpi0: FN02, resource for FAN2 > > acpipwrres3 at acpi0: FN03, resource for FAN3 > > acpipwrres4 at acpi0: FN04, resource for FAN4 > > acpitz0 at acpi0: critical temperature is 101 degC > > acpitz1 at acpi0: critical temperature is 101 degC > > acpibat0 at acpi0: BAT0 not present > > acpibat1 at acpi0: BAT1 not present > > acpibat2 at acpi0: BAT2 not present > > acpibtn0 at acpi0: PWRB > > acpibtn1 at acpi0: LID0 > > acpivideo0 at acpi0: GFX0 > > cpu0: Enhanced SpeedStep 1097 MHz: speeds: 1100, 1000, 900, 800 MHz > > pci0 at mainbus0 bus 0 > > pchb0 at pci0 dev 0 function 0 "Intel Core 2G Host" rev 0x09 > > vga1 at pci0 dev 2 function 0 "Intel HD Graphics 2000" rev 0x09 > > intagp0 at vga1 > > agp0 at intagp0: aperture at 0xe0000000, size 0x10000000 > > inteldrm0 at vga1 > > drm0 at inteldrm0 > > inteldrm0: 1280x1024 > > wsdisplay0 at vga1 mux 1: console (std, vt100 emulation) > > wsdisplay0: screen 1-5 added (std, vt100 emulation) > > "Intel 7 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured > > ehci0 at pci0 dev 26 function 0 "Intel 7 Series USB" rev 0x04: apic 2 > > int 16 > > usb0 at ehci0: USB revision 2.0 > > uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 > > azalia0 at pci0 dev 27 function 0 "Intel 7 Series HD Audio" rev 0x04: > > msi > > azalia0: codecs: Realtek ALC662, Intel/0x2806, using Realtek ALC662 > > audio0 at azalia0 > > ppb0 at pci0 dev 28 function 0 "Intel 7 Series PCIE" rev 0xc4: msi > > pci1 at ppb0 bus 1 > > iwn0 at pci1 dev 0 function 0 "Intel Wireless WiFi Link 4965" rev 0x61: > > msi, MIMO 2T3R, MoW2, address 00:21:5c:04:ca:5f > > ppb1 at pci0 dev 28 function 1 "Intel 7 Series PCIE" rev 0xc4: msi > > pci2 at ppb1 bus 2 > > re0 at pci2 dev 0 function 0 "Realtek 8168" rev 0x0c: RTL8168G/8111G > > (0x4c00), msi, address 80:ee:73:77:d5:a9 > > rgephy0 at re0 phy 7: RTL8251 PHY, rev. 0 > > ppb2 at pci0 dev 28 function 2 "Intel 7 Series PCIE" rev 0xc4: msi > > pci3 at ppb2 bus 3 > > vendor "ASMedia", unknown product 0x1142 (class serial bus subclass USB, > > rev 0x00) at pci3 dev 0 function 0 not configured > > ppb3 at pci0 dev 28 function 3 "Intel 7 Series PCIE" rev 0xc4: msi > > pci4 at ppb3 bus 4 > > re1 at pci4 dev 0 function 0 "Realtek 8168" rev 0x0c: RTL8168G/8111G > > (0x4c00), msi, address 80:ee:73:77:d5:a8 > > rgephy1 at re1 phy 7: RTL8251 PHY, rev. 0 > > ehci1 at pci0 dev 29 function 0 "Intel 7 Series USB" rev 0x04: apic 2 > > int 23 > > usb1 at ehci1: USB revision 2.0 > > uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1 > > pcib0 at pci0 dev 31 function 0 "Intel NM70 LPC" rev 0x04 > > ahci0 at pci0 dev 31 function 2 "Intel 7 Series AHCI" rev 0x04: msi, > > AHCI 1.3 > > scsibus0 at ahci0: 32 targets > > sd0 at scsibus0 targ 2 lun 0: <ATA, TS8GMSM610, 2013> SCSI3 0/direct > > fixed t10.ATA_TS8GMSM610_A93797112253B1000021 > > sd0: 7641MB, 512 bytes/sector, 15649200 sectors > > ichiic0 at pci0 dev 31 function 3 "Intel 7 Series SMBus" rev 0x04: apic > > 2 int 18 > > iic0 at ichiic0 > > spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-10600 SO-DIMM > > isa0 at pcib0 > > isadma0 at isa0 > > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > > pckbc0 at isa0 port 0x60/5 > > pcppi0 at isa0 port 0x61 > > spkr0 at pcppi0 > > it0 at isa0 port 0x2e/2: IT8728F rev 1, EC port 0xa30 > > uhub2 at uhub0 port 1 "Intel Rate Matching Hub" rev 2.00/0.00 addr 2 > > ugen0 at uhub2 port 1 "APC Back-UPS ES 550G FW:870.O2 .I USB FW:O2" rev > > 1.10/1.06 addr 3 > > uhidev0 at uhub2 port 2 configuration 1 interface 0 "NOVATEK USB > > Keyboard" rev 1.10/1.04 addr 4 > > uhidev0: iclass 3/1 > > ukbd0 at uhidev0: 8 variable keys, 6 key codes > > wskbd0 at ukbd0: console keyboard, using wsdisplay0 > > uhidev1 at uhub2 port 2 configuration 1 interface 1 "NOVATEK USB > > Keyboard" rev 1.10/1.04 addr 4 > > uhidev1: iclass 3/0, 2 report ids > > uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0 > > uhid1 at uhidev1 reportid 2: input=3, output=0, feature=0 > > uhub3 at uhub1 port 1 "Intel Rate Matching Hub" rev 2.00/0.00 addr 2 > > umass0 at uhub3 port 2 configuration 1 interface 0 "Generic USB Storage" > > rev 2.00/94.54 addr 3 > > umass0: using SCSI over Bulk-Only > > scsibus1 at umass0: 2 targets, initiator 0 > > sd1 at scsibus1 targ 1 lun 0: <Generic, STORAGE DEVICE, 9454> SCSI0 > > 0/direct removable > > uhub4 at uhub3 port 3 "TRANSCEND USB2.0 Hub" rev 2.00/90.30 addr 4 > > umass1 at uhub4 port 3 configuration 1 interface 0 "Intenso USB 3.0 > > Device" rev 2.10/1.00 addr 5 > > umass1: using SCSI over Bulk-Only > > scsibus2 at umass1: 2 targets, initiator 0 > > sd2 at scsibus2 targ 1 lun 0: <Intenso, USB 3.0 Device, 0> SCSI4 > > 0/direct fixed serial.174c55aa000000001EA0 > > sd2: 2861588MB, 4096 bytes/sector, 732566646 sectors > > umass2 at uhub4 port 4 configuration 1 interface 0 "Intenso USB 3.0 > > Device" rev 2.10/1.00 addr 6 > > umass2: using SCSI over Bulk-Only > > scsibus3 at umass2: 2 targets, initiator 0 > > sd3 at scsibus3 targ 1 lun 0: <Intenso, USB 3.0 Device, 0> SCSI4 > > 0/direct fixed serial.174c55aa000000004CC1 > > sd3: 2861588MB, 4096 bytes/sector, 732566646 sectors > > uhub5 at uhub3 port 4 "TRANSCEND USB2.0 Hub" rev 2.00/90.30 addr 7 > > umass3 at uhub5 port 3 configuration 1 interface 0 "Intenso USB 3.0 > > Device" rev 2.10/1.00 addr 8 > > umass3: using SCSI over Bulk-Only > > scsibus4 at umass3: 2 targets, initiator 0 > > sd4 at scsibus4 targ 1 lun 0: <Intenso, USB 3.0 Device, 0> SCSI4 > > 0/direct fixed serial.174c55aa000000001F1F > > sd4: 2861588MB, 4096 bytes/sector, 732566646 sectors > > umass4 at uhub5 port 4 configuration 1 interface 0 "Intenso USB 3.0 > > Device" rev 2.10/1.00 addr 9 > > umass4: using SCSI over Bulk-Only > > scsibus5 at umass4: 2 targets, initiator 0 > > sd5 at scsibus5 targ 1 lun 0: <Intenso, USB 3.0 Device, 0> SCSI4 > > 0/direct fixed serial.174c55aa0000000022DF > > sd5: 2861588MB, 4096 bytes/sector, 732566646 sectors > > vscsi0 at root > > scsibus6 at vscsi0: 256 targets > > softraid0 at root > > scsibus7 at softraid0: 256 targets > > root on sd0a (cc476e21b86f4015.a) swap on sd0b dump on sd0b > > softraid0: sd2a has unsupported sector size (4096) > > softraid0: invalid metadata format > > > !DSPAM:5329c1ac270299089480116!
