Hello,
I used to change the behavior of my keyboard with
/etc/wsconsctl.conf:
keyboard.repeat.del1=200 # change keyboard repeat/delay
keyboard.repeat.deln=40
Now I plugged it to usb (see dmesg) - but from then on I am not able
to change the behavior anymore with wsconsctl. I am not sure but is
wsconsctl not able to change the settings of
keyboard.repeat.del1 and keyboard.repeat.deln
for USB keyboards?
Here is my dmesg:
OpenBSD 3.8 (GENERIC) #138: Sat Sep 10 15:41:37 MDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class, 128KB L2 cache) 898 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem = 267952128 (261672K)
avail mem = 237613056 (232044K)
using 3296 buffers containing 13500416 bytes (13184K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(bb) BIOS, date 08/13/01, BIOS32 rev. 0 @ 0xfb460
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb8e0
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdd00/144 (7 entries)
pcibios0: PCI Exclusive IRQs: 10 11
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C596A ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xa000 0xcc000/0x4000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT82C691 PCI" rev 0xc4
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "Nvidia Vanta" rev 0x11
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C686 ISA" rev 0x40
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x06: ATA100, channel 0
configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <ST340015A>
wd0: 16-sector PIO, LBA, 38166MB, 78165360 sectors
wd1 at pciide0 channel 0 drive 1: <WDC WD800BB-00DAA3>
wd1: 16-sector PIO, LBA48, 76319MB, 156301488 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, DV-516E, 2.01> SCSI0 5/cdrom removable
atapiscsi1 at pciide0 channel 1 drive 1
scsibus1 at atapiscsi1: 2 targets
cd1 at scsibus1 targ 0 lun 0: <MITSUMI, CR-48X8TE, 1.1B> SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
cd1(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 7 function 2 "VIA VT83C572 USB" rev 0x16: irq 10
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 7 function 3 "VIA VT83C572 USB" rev 0x16: irq 10
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
viaenv0 at pci0 dev 7 function 4 "VIA VT82C686 SMBus" rev 0x40
rl0 at pci0 dev 15 function 0 "Realtek 8139" rev 0x10: irq 11 address
00:40:f4:63:c0:f5
rlphy0 at rl0 phy 0: RTL internal phy
cmpci0 at pci0 dev 17 function 0 "C-Media Electronics CMI8738/C3DX Audio" rev
0x10: irq 10
audio0 at cmpci0
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask f765 netmask ff65 ttymask ffe7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
uhub2 at uhub0 port 1
uhub2: Genesys Logic USB2.0 Hub, rev 2.00/6.0b, addr 2
uhub2: 4 ports with 4 removable, self powered
uhidev0 at uhub0 port 2 configuration 1 interface 0
uhidev0: Logitech USB Receiver, rev 1.10/21.00, addr 3, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub0 port 2 configuration 1 interface 1
uhidev1: Logitech USB Receiver, rev 1.10/21.00, addr 3, iclass 3/1
uhidev1: 4 report ids
ums0 at uhidev1 reportid 1: 16 buttons and Z dir.
wsmouse0 at ums0 mux 0
uhid0 at uhidev1 reportid 2: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=1, output=0, feature=0
uhid2 at uhidev1 reportid 4: input=3, output=0, feature=0
wd0: no disk label
dkcsum: wd0 matches BIOS drive 0x80
dkcsum: wd1 matches BIOS drive 0x81
root on wd1a
rootdev=0x10 rrootdev=0x310 rawdev=0x312
Oliver
--
... don't touch the bang bang fruit
