On Mon, Jun 15, 2015 at 11:17:04PM +0200, Riccardo Mottola wrote: > Hi, > > on my HP laptop (dmesg below) I notice that both with acpi and with apm, > it is always reported that the power adapter is connected, even if it is > not. The power level of the battery seems reasonable.
Can you send an acpidump please? -ml > > With power cord attached: > hw.sensors.acpitz0.temp0=56.00 degC (zone temperature) > hw.sensors.acpiac0.indicator0=On (power supply) > hw.sensors.acpibat0.volt0=14.80 VDC (voltage) > hw.sensors.acpibat0.volt1=12.48 VDC (current voltage) > hw.sensors.acpibat0.current0=unknown (rate), UNKNOWN > hw.sensors.acpibat0.amphour0=4.10 Ah (last full capacity) > hw.sensors.acpibat0.amphour1=0.21 Ah (warning capacity) > hw.sensors.acpibat0.amphour2=0.12 Ah (low capacity) > hw.sensors.acpibat0.amphour3=4.10 Ah (remaining capacity), OK > hw.sensors.acpibat0.amphour4=6.00 Ah (design capacity) > hw.sensors.acpibat0.raw0=0 (battery full), OK > hw.sensors.acpibtn2.indicator0=On (lid open) > > Without: > hw.sensors.acpitz0.temp0=56.00 degC (zone temperature) > hw.sensors.acpiac0.indicator0=On (power supply) > hw.sensors.acpibat0.volt0=14.80 VDC (voltage) > hw.sensors.acpibat0.volt1=11.84 VDC (current voltage) > hw.sensors.acpibat0.current0=unknown (rate), UNKNOWN > hw.sensors.acpibat0.amphour0=4.10 Ah (last full capacity) > hw.sensors.acpibat0.amphour1=0.21 Ah (warning capacity) > hw.sensors.acpibat0.amphour2=0.12 Ah (low capacity) > hw.sensors.acpibat0.amphour3=4.00 Ah (remaining capacity), OK > hw.sensors.acpibat0.amphour4=6.00 Ah (design capacity) > hw.sensors.acpibat0.raw0=1 (battery discharging), OK > hw.sensors.acpibtn2.indicator0=On (lid open) > > > acpiac0 seems wrong to me. > > Riccardo > > OpenBSD 5.7 (GENERIC.MP) #881: Sun Mar 8 11:04:17 MDT 2015 > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP > real mem = 2129461248 (2030MB) > avail mem = 2068914176 (1973MB) > mpath0 at root > scsibus0 at mpath0: 256 targets > mainbus0 at root > bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xdc010 (19 entries) > bios0: vendor Hewlett-Packard version "F.58" date 06/16/2008 > bios0: Hewlett-Packard HP Pavilion dv6500 Notebook PC > acpi0 at bios0: rev 2 > acpi0: sleep states S0 S3 S4 S5 > acpi0: tables DSDT FACP HPET MCFG TMOR APIC BOOT SLIC SSDT SSDT SSDT SSDT > acpi0: wakeup devices PWRB(S4) PXSX(S3) PXSX(S4) PS2K(S3) PS2M(S3) > acpitimer0 at acpi0: 3579545 Hz, 24 bits > acpihpet0 at acpi0: 14318179 Hz > acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255 > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat > cpu0 at mainbus0: apid 0 (boot processor) > cpu0: Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz, 2394.68 MHz > cpu0: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,NXE,LONG,LAHF,PERF > cpu0: 4MB 64b/line 16-way L2 cache > cpu0: smt 0, core 0, package 0 > mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges > cpu0: apic clock running at 199MHz > cpu0: mwait min=64, max=64, C-substates=0.2.2.2.2, IBE > cpu1 at mainbus0: apid 1 (application processor) > cpu1: Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz, 2194.75 MHz > cpu1: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,NXE,LONG,LAHF,PERF > cpu1: 4MB 64b/line 16-way L2 cache > cpu1: smt 0, core 1, package 0 > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins > acpiprt0 at acpi0: bus 0 (PCI0) > acpiprt1 at acpi0: bus 1 (PEGP) > acpiprt2 at acpi0: bus 2 (RP01) > acpiprt3 at acpi0: bus 4 (RP02) > acpiprt4 at acpi0: bus 8 (RP06) > acpiprt5 at acpi0: bus 9 (PCIB) > acpiec0 at acpi0 > acpicpu0 at acpi0: C3, C2, C1, PSS > acpicpu1 at acpi0: C3, C2, C1, PSS > acpitz0 at acpi0acpitz0: THR1: failed to read _CRT > acpitz0: THR1: failed to read _CRT > : no critical temperature defined > acpibtn0 at acpi0: PWRB > acpibtn1 at acpi0: SLPB > acpiac0 at acpi0: AC unit online > acpibat0 at acpi0: BAT0 model "Primary" serial type LION oem > "Hewlett-Packard" > acpibtn2 at acpi0: LID_ > acpivideo0 at acpi0: VGA_ > acpivout0 at acpivideo0: LCD_ > acpivideo1 at acpi0: GFX0 > cpu0: Enhanced SpeedStep 2394 MHz: speeds: 2201, 2200, 1600, 1200, 800 MHz > pci0 at mainbus0 bus 0 > pchb0 at pci0 dev 0 function 0 "Intel GM965 Host" rev 0x0c > ppb0 at pci0 dev 1 function 0 "Intel GM965 PCIE" rev 0x0c: msi > pci1 at ppb0 bus 1 > vga1 at pci1 dev 0 function 0 "NVIDIA GeForce 8400M GS" rev 0xa1 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > uhci0 at pci0 dev 26 function 0 "Intel 82801H USB" rev 0x03: apic 2 int 16 > uhci1 at pci0 dev 26 function 1 "Intel 82801H USB" rev 0x03: apic 2 int 21 > ehci0 at pci0 dev 26 function 7 "Intel 82801H USB" rev 0x03: apic 2 int 18 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 > azalia0 at pci0 dev 27 function 0 "Intel 82801H HD Audio" rev 0x03: msi > azalia0: codecs: Realtek ALC268, Motorola/0x3055, using Realtek ALC268 > audio0 at azalia0 > ppb1 at pci0 dev 28 function 0 "Intel 82801H PCIE" rev 0x03: msi > pci2 at ppb1 bus 2 > wpi0 at pci2 dev 0 function 0 "Intel PRO/Wireless 3945ABG" rev 0x02: > msi, MoW2, address 00:1c:bf:0d:dc:cc > ppb2 at pci0 dev 28 function 1 "Intel 82801H PCIE" rev 0x03: msi > pci3 at ppb2 bus 4 > ppb3 at pci0 dev 28 function 5 "Intel 82801H PCIE" rev 0x03: msi > pci4 at ppb3 bus 8 > re0 at pci4 dev 0 function 0 "Realtek 8101E" rev 0x01: RTL8101E > (0x3400), msi, address 00:1b:24:b9:4d:0f > rlphy0 at re0 phy 7: RTL8201L 10/100 PHY, rev. 1 > uhci2 at pci0 dev 29 function 0 "Intel 82801H USB" rev 0x03: apic 2 int 23 > uhci3 at pci0 dev 29 function 1 "Intel 82801H USB" rev 0x03: apic 2 int 19 > uhci4 at pci0 dev 29 function 2 "Intel 82801H USB" rev 0x03: apic 2 int 18 > ehci1 at pci0 dev 29 function 7 "Intel 82801H USB" rev 0x03: apic 2 int 23 > usb1 at ehci1: USB revision 2.0 > uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1 > ppb4 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xf3 > pci5 at ppb4 bus 9 > "Ricoh 5C832 Firewire" rev 0x05 at pci5 dev 9 function 0 not configured > sdhc0 at pci5 dev 9 function 1 "Ricoh 5C822 SD/MMC" rev 0x22: apic 2 int 21 > sdmmc0 at sdhc0 > "Ricoh 5C843 MMC" rev 0x12 at pci5 dev 9 function 2 not configured > "Ricoh 5C592 Memory Stick" rev 0x12 at pci5 dev 9 function 3 not configured > "Ricoh 5C852 xD" rev 0x12 at pci5 dev 9 function 4 not configured > pcib0 at pci0 dev 31 function 0 "Intel 82801HBM LPC" rev 0x03 > pciide0 at pci0 dev 31 function 1 "Intel 82801HBM IDE" rev 0x03: DMA, > channel 0 configured to compatibility, channel 1 configured to compatibility > atapiscsi0 at pciide0 channel 0 drive 0 > scsibus1 at atapiscsi0: 2 targets > cd0 at scsibus1 targ 0 lun 0: <PIONEER, DVDRW DVR-K17B, 1.02> ATAPI > 5/cdrom removable > cd0(pciide0:0:0): using PIO mode 4, DMA mode 2 > pciide0: channel 1 disabled (no drives) > ahci0 at pci0 dev 31 function 2 "Intel 82801HBM AHCI" rev 0x03: msi, > AHCI 1.1 > ahci0: PHY offline on port 1 > scsibus2 at ahci0: 32 targets > sd0 at scsibus2 targ 0 lun 0: <ATA, WDC WD2500BEVS-6, 01.0> SCSI3 > 0/direct fixed naa.50014ee2ab4625a6 > sd0: 238475MB, 512 bytes/sector, 488397168 sectors > ichiic0 at pci0 dev 31 function 3 "Intel 82801H SMBus" rev 0x03: apic 2 > int 19 > iic0 at ichiic0 > spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM > spdmem1 at iic0 addr 0x52: 1GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM > usb2 at uhci0: USB revision 1.0 > uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > usb3 at uhci1: USB revision 1.0 > uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > usb4 at uhci2: USB revision 1.0 > uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > usb5 at uhci3: USB revision 1.0 > uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > usb6 at uhci4: USB revision 1.0 > uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > isa0 at pcib0 > isadma0 at isa0 > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pms0 at pckbc0 (aux slot) > pckbc0: using irq 12 for aux slot > wsmouse0 at pms0 mux 0 > pms0: Synaptics touchpad, firmware 6.3 > pcppi0 at isa0 port 0x61 > spkr0 at pcppi0 > uvideo0 at uhub1 port 4 configuration 1 interface 0 "Chicony Electronics > Co., Ltd. HP Webcam" rev 2.00/6.06 addr 2 > video0 at uvideo0 > ugen0 at uhub5 port 1 "AuthenTec Fingerprint Sensor" rev 1.10/6.23 addr 2 > vscsi0 at root > scsibus3 at vscsi0: 256 targets > softraid0 at root > scsibus4 at softraid0: 256 targets > root on sd0a (255b4caf4f8b1563.a) swap on sd0b dump on sd0b
