Hi, i've bought an new device. x86duino educake. there is a dmesg that looks like it has worked with openbsd 5.4 [1]. I'm trying to run 5.7 release on it an getting a panic. any ideas ?
jan [1] http://www2192ue.sakura.ne.jp/~uaa/gomitext/2014/20140219/dmesg.txt >> OpenBSD/i386 BOOT 3.26 boot> booting hd0a:/bsd: 9777628+1068236 [72+409680+404343]=0xb1ec54 entry point at 0x200120 [ using 814508 bytes of bsd ELF symbol table ] Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2015 OpenBSD. All rights reserved. http://www.OpenBSD.org OpenBSD 5.7 (GENERIC) #738: Sun Mar 8 10:59:31 MDT 2015 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC RTC BIOS diagnostic error b<fixed_disk> cpu0: Vortex86 SoC (686-class) 301 MHz cpu0: FPU,TSC,CX8,SEP,CMOV,MMX,PERF real mem = 133246976 (127MB) avail mem = 118726656 (113MB) mpath0 at root scsibus0 at mpath0: 256 targets mainbus0 at root bios0 at mainbus0: date 06/23/99, BIOS32 rev. 0 @ 0xff046, SMBIOS rev. 2.7 @ 0x7fe1420 (6 entries) bios0: vendor coreboot version "4.0-4750-g745041e" date 09/02/2014 bios0: DMP Vortex86EX acpi at bios0 function 0x0 not configured pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf4d30/224 (12 entries) pcibios0: no compatible PCI ICU found: ICU vendor 0x17f3 product 0x6011 pcibios0: Warning, unable to fix up PCI interrupt routing pcibios0: PCI bus #1 is the last bus bios0: ROM list: 0xef000/0x1000! cpu0 at mainbus0: (uniprocessor) pci0 at mainbus0 bus 0: configuration mode 1 (bios) pchb0 at pci0 dev 0 function 0 "RDC R6025 Host" rev 0x01 ppb0 at pci0 dev 1 function 0 "RDC R1031 PCIe" rev 0x02: irq 15 pci1 at ppb0 bus 1 pcib0 at pci0 dev 7 function 0 "RDC R6011 SB" rev 0x01 pcib1 at pci0 dev 7 function 1 "RDC R6011 SB" rev 0x01 vte0 at pci0 dev 8 function 0 "RDC R6040 Ethernet" rev 0x00: irq 9, address 00:1b:eb:64:ae:d4 ukphy0 at vte0 phy 1: Generic IEEE 802.3u media interface, rev. 0: OUI 0x000bb4, model 0x0005 ohci0 at pci0 dev 10 function 0 "RDC R6060 USB" rev 0x13: irq 14, version 1.0, legacy support ehci0 at pci0 dev 10 function 1 "RDC R6061 USB2" rev 0x07: irq 10 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "RDC EHCI root hub" rev 2.00/1.00 addr 1 pciide0 at pci0 dev 12 function 0 "RDC R1012 IDE" rev 0x03: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI pciide0: using irq 11 for native-PCI interrupt wd0 at pciide0 channel 0 drive 0: <SD04G D0 RDC SD-IDE HOST CONTROLLER> wd0: 1-sector PIO, LBA, 3781MB, 7744512 sectors pciide0: channel 1 ignored (disabled) azalia0 at pci0 dev 14 function 0 "RDC R3010 HDA" rev 0x02: irq 7 azalia0: codecs: Realtek ALC262 audio0 at azalia0 "RDC R1060 USB Device" rev 0x03 at pci0 dev 15 function 0 not configured "RDC R1331 MC" rev 0x00 at pci0 dev 16 function 0 not configured "RDC R1710 SPI" rev 0x01 at pci0 dev 16 function 1 not configured "RDC R1070 CAN" rev 0x00 at pci0 dev 17 function 0 not configured isa0 at pcib0 isadma0 at isa0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo com2 at isa0 port 0x3e8/8 irq 5: ns16550a, 16 byte fifo pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard pcppi0 at isa0 port 0x61 spkr0 at pcppi0 npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 pcic: does not support memory and I/O cards, ignored (ident=3) pcic: does not support memory and I/O cards, ignored (ident=3) pcic: does not support memory and I/O cards, ignored (ident=3) pcic: does not support memory and I/O cards, ignored (ident=3) isa at pcib1 not configured usb1 at ohci0: USB revision 1.0 uhub1 at usb1 "RDC OHCI root hub" rev 1.00/1.00 addr 1 nvram: invalid checksum uvm_fault(0xd0b984c0, 0x0, 0, 1) -> e kernel: page fault trap, code=0 Stopped at wdcintr+0x85: call *0(%edx) ddb> trace wdcintr(d10385e4,0,1,0,0) at wdcintr+0x85 pciide_pci_intr(d1038000,d1034900) at pciide_pci_intr+0x69 Xrecurse_legacy11() at Xrecurse_legacy11+0xb9 --- interrupt ---Xspllower(d322c870) at Xddb> show registers ds 0x10 es 0x10 fs 0x20 gs 0 edi 0xd10385e4 end+0x3e061c esi 0xd10385e4 end+0x3e061c ebp 0xf1e0aed0 ebx 0xd1038508 end+0x3e0540 edx 0 ecx 0x10 eax 0 eip 0xd0208315 wdcintr+0x85 cs 0x8 eflags 0x256 esp 0xf1e0ae98 ss 0x10 wdcintr+0x85: call *0(%edx) spllower+0xe Bad frame pointer: 0xd0d20e18
