On 18/01/14 13:40, Alexey E. Suslikov wrote:
the source tree as part of the regular 'make' call. But this way I
managed to compile the kernel and install it.
you didn't tell us is your urtwn(4) variant working or not after installing
new kernel. new dmesg wouldn't hurt.
Sorry for the late answer. The card seems to be recognized, see dmesg
below (a little censored with XX).
I still have problems getting it up to run; scanning works, but I cannot
seem to setup a stable WPA connection. It is probably me, so I will
continue to play around.
I am a little disappointed that the hostap is not supported, but that
was well documented.
Bernd
OpenBSD 5.4 (GENERIC) #0: Sat Jan 18 06:56:40 GMT 2014
root@XXXXXXXX:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Vortex86 SoC (586-class) 934 MHz
cpu0: FPU,TSC,CX8,MMX
real mem = 1039724544 (991MB)
avail mem = 1011290112 (964MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 11/26/10, BIOS32 rev. 0 @ 0xf0010
apm0 at bios0: Power Management spec V1.2
pcibios0 at bios0: rev 3.0 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf2fe0/240 (13 entries)
pcibios0: no compatible PCI ICU found: ICU vendor 0x17f3 product 0x6036
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 vendor "RDC", unknown product 0x6022 rev
0x00
rl0 at pci0 dev 1 function 0 "Realtek 8139" rev 0x10: irq 11, address
44:4d:50:07:1b:19
rlphy0 at rl0 phy 0: RTL internal PHY
rl1 at pci0 dev 2 function 0 "Realtek 8139" rev 0x10: irq 11, address
44:4d:50:07:1b:1a
rlphy1 at rl1 phy 0: RTL internal PHY
pcib0 at pci0 dev 7 function 0 vendor "RDC", unknown product 0x6036 rev
0x00
vte0 at pci0 dev 8 function 0 "RDC R6040 Ethernet" rev 0x00: irq 6,
address 00:1b:eb:25:30:9e
rdcphy0 at vte0 phy 1: R6040 10/100 PHY, rev. 1
ohci0 at pci0 dev 10 function 0 "RDC R6060 USB" rev 0x12: irq 7, version
1.0, legacy support
ehci0 at pci0 dev 10 function 1 "RDC R6061 USB" rev 0x03: irq 3
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "RDC EHCI root hub" rev 2.00/1.00 addr 1
ohci1 at pci0 dev 11 function 0 "RDC R6060 USB" rev 0x12: irq 5, version
1.0, legacy support
ehci1 at pci0 dev 11 function 1 "RDC R6061 USB" rev 0x03: irq 9
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "RDC EHCI root hub" rev 2.00/1.00 addr 1
pciide0 at pci0 dev 12 function 0 "RDC R1011 IDE" rev 0x01: DMA
(unsupported), channel 0 configured to compatibility, channel 1
configured to compatibility
pciide0: channel 0 ignored (not responding; disabled or no drives?)
wd0 at pciide0 channel 1 drive 0: <ST9320421AS>
wd0: 16-sector PIO, LBA48, 305245MB, 625142448 sectors
vga1 at pci0 dev 13 function 0 vendor "RDC", unknown product 0x2012 rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
azalia0 at pci0 dev 14 function 0 vendor "RDC", unknown product 0x3010
rev 0x01: irq 10
azalia0: codecs: Realtek ALC262
audio0 at azalia0
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: probed fifo depth: 0 bytes
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 "RDC OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 "RDC OHCI root hub" rev 1.00/1.00 addr 1
umass0 at uhub0 port 1 configuration 1 interface 0 "Generic Mass Storage
Device" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Multi, Flash Reader, 1.00> SCSI0 0/direct
removable serial.058f6366058F0O1111B1
sd0: 248MB, 512 bytes/sector, 508928 sectors
uhidev0 at uhub2 port 2 configuration 1 interface 0 "Logitech USB
Receiver" rev 1.10/9.10 addr 2
uhidev0: iclass 3/1
ums0 at uhidev0: 5 buttons, Z dir
wsmouse0 at ums0 mux 0
uhidev1 at uhub3 port 2 configuration 1 interface 0 "Cherry
Mikroschalter product 0x0011" rev 2.00/1.00 addr 2
uhidev1: iclass 3/1
ukbd0 at uhidev1: 8 variable keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on wd0a (197b846eebaa6c90.a) swap on wd0b dump on wd0b
WARNING: / was not properly unmounted
sd0 detached
scsibus0 detached
umass0 detached
urtwn0 at uhub0 port 1 "Realtek 802.11n WLAN Adapter" rev 2.00/2.00 addr 2
urtwn0: MAC/BB RTL8192CU, RF 6052 2T2R, address XX:XX:XX:XX:XX:XX
