I'm getting a lot of watchdog timeouts on re0 with the i386 snapshots.
re0 is a Traverse Viking PCI ADSL card. Is there something I need to set
or tune on my end to stop the timeouts?
Regards,
/Lars
OpenBSD 5.4-current (GENERIC) #148: Tue Nov 12 15:18:10 MST 2013
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 500
MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
real mem = 536408064 (511MB)
avail mem = 515809280 (491MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/70/03, BIOS32 rev. 0 @ 0xfac40
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa800
cpu0 at mainbus0: (uniprocessor)
amdmsr0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
0:20:0: io address conflict 0x6100/0x100
0:20:0: io address conflict 0x6200/0x200
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
00:00:24:cb:a9:24
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5, address
00:00:24:cb:a9:25
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9, address
00:00:24:cb:a9:26
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address
00:00:24:cb:a9:27
ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
re0 at pci0 dev 14 function 0 "Realtek 8139" rev 0x20: RTL8139C+ (0x7480), irq
10, address 00:0a:fa:20:03:79
rlphy0 at re0 phy 0: RTL internal PHY
ral0 at pci0 dev 17 function 0 "Ralink RT2561S" rev 0x00: irq 15, address
00:12:0e:61:54:68
ral0: MAC/BBP RT2561C, RF RT5225
glxpcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio, i2c
gpio0 at glxpcib0: 32 pins
iic0 at glxpcib0
pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFH-004G>
wd0: 1-sector PIO, LBA48, 3825MB, 7835184 sectors
wd1 at pciide0 channel 0 drive 1: <ELITE PRO CF CARD 4GB>
wd1: 1-sector PIO, LBA, 3823MB, 7831152 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 7, version 1.0,
legacy support
ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 7
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
mtrr: K6-family MTRR support (2 registers)
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
scsibus1 at softraid0: 256 targets
softraid0: sd0 was not shutdown properly
sd0 at scsibus1 targ 1 lun 0: <OPENBSD, SR RAID 0, 005> SCSI2 0/direct fixed
sd0: 7102MB, 512 bytes/sector, 14546176 sectors
root on wd0a (a7a34fe3558d6dac.a) swap on wd0b dump on wd0b
WARNING: / was not properly unmounted
umass0 at uhub0 port 1 configuration 1 interface 0 "JetFlash Mass Storage
Device" rev 2.00/1.42 addr 2
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets, initiator 0
sd1 at scsibus2 targ 1 lun 0: <JetFlash, Transcend 4GB, 8.07> SCSI2 0/direct
removable
sd1: 3911MB, 512 bytes/sector, 8011774 sectors
syncing disks... done
sd0 detached
OpenBSD 5.4-current (RAMDISK_CD) #108: Thu Nov 14 00:51:25 MST 2013
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 500
MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
real mem = 536408064 (511MB)
avail mem = 520384512 (496MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/70/03, BIOS32 rev. 0 @ 0xfac40
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa800
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
0:20:0: io address conflict 0x6100/0x100
0:20:0: io address conflict 0x6200/0x200
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
"AMD Geode LX Crypto" rev 0x00 at pci0 dev 1 function 2 not configured
vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
00:00:24:cb:a9:24
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5, address
00:00:24:cb:a9:25
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9, address
00:00:24:cb:a9:26
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address
00:00:24:cb:a9:27
ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
re0 at pci0 dev 14 function 0 "Realtek 8139" rev 0x20: RTL8139C+ (0x7480), irq
10, address 00:0a:fa:20:03:79
rlphy0 at re0 phy 0: RTL internal PHY
ral0 at pci0 dev 17 function 0 "Ralink RT2561S" rev 0x00: irq 15, address
00:12:0e:61:54:68
ral0: MAC/BBP RT2561C, RF RT5225
pcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03
pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFH-004G>
wd0: 1-sector PIO, LBA48, 3825MB, 7835184 sectors
wd1 at pciide0 channel 0 drive 1: <ELITE PRO CF CARD 4GB>
wd1: 1-sector PIO, LBA, 3823MB, 7831152 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 7, version 1.0,
legacy support
ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 7
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
softraid0 at root
scsibus0 at softraid0: 256 targets
sd0 at scsibus0 targ 1 lun 0: <OPENBSD, SR RAID 0, 005> SCSI2 0/direct fixed
sd0: 7102MB, 512 bytes/sector, 14546176 sectors
root on rd0a swap on rd0b dump on rd0b
umass0 at uhub0 port 1 configuration 1 interface 0 "JetFlash Mass Storage
Device" rev 2.00/1.42 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <JetFlash, Transcend 4GB, 8.07> SCSI2 0/direct
removable
sd1: 3911MB, 512 bytes/sector, 8011774 sectors
syncing disks... done
sd0 detached
OpenBSD 5.4-current (GENERIC) #150: Thu Nov 14 00:34:42 MST 2013
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 500
MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
real mem = 536408064 (511MB)
avail mem = 515813376 (491MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/70/03, BIOS32 rev. 0 @ 0xfac40
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa800
cpu0 at mainbus0: (uniprocessor)
amdmsr0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
0:20:0: io address conflict 0x6100/0x100
0:20:0: io address conflict 0x6200/0x200
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
00:00:24:cb:a9:24
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5, address
00:00:24:cb:a9:25
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9, address
00:00:24:cb:a9:26
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address
00:00:24:cb:a9:27
ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
re0 at pci0 dev 14 function 0 "Realtek 8139" rev 0x20: RTL8139C+ (0x7480), irq
10, address 00:0a:fa:20:03:79
rlphy0 at re0 phy 0: RTL internal PHY
ral0 at pci0 dev 17 function 0 "Ralink RT2561S" rev 0x00: irq 15, address
00:12:0e:61:54:68
ral0: MAC/BBP RT2561C, RF RT5225
glxpcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio, i2c
gpio0 at glxpcib0: 32 pins
iic0 at glxpcib0
pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFH-004G>
wd0: 1-sector PIO, LBA48, 3825MB, 7835184 sectors
wd1 at pciide0 channel 0 drive 1: <ELITE PRO CF CARD 4GB>
wd1: 1-sector PIO, LBA, 3823MB, 7831152 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 7, version 1.0,
legacy support
ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 7
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
mtrr: K6-family MTRR support (2 registers)
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
scsibus1 at softraid0: 256 targets
sd0 at scsibus1 targ 1 lun 0: <OPENBSD, SR RAID 0, 005> SCSI2 0/direct fixed
sd0: 7102MB, 512 bytes/sector, 14546176 sectors
root on wd0a (a7a34fe3558d6dac.a) swap on wd0b dump on wd0b
re0: watchdog timeout
re0: watchdog timeout
re0: watchdog timeout
re0: watchdog timeout
re0: watchdog timeout
re0: watchdog timeout
umass0 at uhub0 port 1 configuration 1 interface 0 "JetFlash Mass Storage
Device" rev 2.00/1.42 addr 2
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets, initiator 0
sd1 at scsibus2 targ 1 lun 0: <JetFlash, Transcend 4GB, 8.07> SCSI2 0/direct
removable
sd1: 3911MB, 512 bytes/sector, 8011774 sectors
re0: watchdog timeout
