I need to add a NIC to the PCI-X slot(s) of Proliant to communicate to the
UPS.
First, I tried an RTL8139 board. It would not POST ('bus master error').
This goes to RTL // HP.
Next, an original Intel xln. It was recognized, the Proliant asked for the
change in boot order, I could allocate an irq. Everything fine.
Booting, however, results in a crash; the board is not recognised (if it
isn't, why can it crash ?). In any case, the NIC does not show, and the
box automatically re-enters BIOS-boot after a few seconds after rpc.
I tried twice; and twice the same effect: auto-reboot.
Question: Anybody out there with a successful addition of a NIC to that
machine ? Anything else to recommend ? (I don't have a 905 on hand, so I
couldn't try that one.)
Uwe
dmesg, the last four lines are the automatic reboot:
booting hd0a:/bsd: 4846336+944176 [52+249680+230986]=0x5fb274
entry point at 0x100120
m
[ using 481092 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2005 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 3.8 (GENERIC.MP) #0: Wed Nov 2 10:11:33 SGT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Xeon(TM) CPU 3.00GHz ("GenuineIntel" 686-class) 3 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CDreal
mem = 2147012608 (2096692K)
avail mem = 1953050624 (1907276K)
using 4278 buffers containing 107454464 bytes (104936K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 12/31/99, BIOS32 rev. 0 @ 0xf0000
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x2000
pcibios0: PCI BIOS has 10 Interrupt Routing table entries
pcibios0: no compatible PCI ICU found
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #7 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x4000 0xcc000/0x1000 0xcd000/0x1600
0x!mainbus0: Intel MP Specification (Version 1.4) (HP PROLIANT )
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 200 MHz
cpu1 at mainbus0: apid 6 (application processor)
cpu1: Intel(R) Xeon(TM) CPU 3.00GHz ("GenuineIntel" 686-class) 3 GHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CDmainbus0:
bus 0 is type PCI
mainbus0: bus 1 is type PCI
mainbus0: bus 2 is type PCI
mainbus0: bus 5 is type PCI
mainbus0: bus 6 is type PCI
mainbus0: bus 9 is type PCI
mainbus0: bus 13 is type PCI
mainbus0: bus 16 is type PCI
mainbus0: bus 32 is type ISA
ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 20, 24 pins
ioapic1 at mainbus0: apid 9 pa 0xfec10000, version 20, 24 pins
ioapic1: misconfigured as apic 0, remapped to apic 9
ioapic2 at mainbus0: apid 10 pa 0xfec80000, version 20, 24 pins
ioapic3 at mainbus0: apid 11 pa 0xfec80400, version 20, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel E7710 SMCH" rev 0x0c
ppb0 at pci0 dev 2 function 0 "Intel E7710 MCH PCIE" rev 0x0c
pci1 at ppb0 bus 1
ppb1 at pci1 dev 0 function 0 "Intel PCIE-PCIE" rev 0x09
pci2 at ppb1 bus 2
ppb2 at pci1 dev 0 function 2 "Intel PCIE-PCIE" rev 0x09
pci3 at ppb2 bus 3
fxp0 at pci3 dev 2 function 0 "Intel 82557" rev 0x08, i82559: apic 8 int 3
(irqainphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
ppb3 at pci0 dev 4 function 0 "Intel E7710 MCH PCIE" rev 0x0c
pci4 at ppb3 bus 4
ppb4 at pci0 dev 6 function 0 "Intel E7710 MCH PCIE" rev 0x0c
pci5 at ppb4 bus 5
ppb5 at pci0 dev 28 function 0 "Intel 6300ESB PCIX" rev 0x02
pci6 at ppb5 bus 6
mpt0 at pci6 dev 3 function 0 "Symbios Logic 53c1030" rev 0x08: apic 8 int 5
(i)mpt0: sending FW Upload request to IOC (size: 36, img size: 40752)
mpt0: IM support: 0
scsibus0 at mpt0: 16 targets
sd0 at scsibus0 targ 0 lun 0: <COMPAQ, BF14686842, HPB4> SCSI3 0/direct fixed
sd0: 140014MB, 41991 cyl, 10 head, 682 sec, 512 bytes/sec, 286749488 sec total
mpt0: target 0 Synchronous at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1
mpt1 at pci6 dev 3 function 1 "Symbios Logic 53c1030" rev 0x08: apic 8 int 5
(i)mpt1: sending FW Upload request to IOC (size: 36, img size: 40752)
mpt1: IM support: 0
scsibus1 at mpt1: 16 targets
uhci0 at pci0 dev 29 function 0 "Intel 6300ESB USB" rev 0x02: apic 8 int 16
(ir)usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 5300ESB USB" rev 0x02: apic 8 int 19
(ir)usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
"Intel 6300ESB WDT" rev 0x02 at pci0 dev 29 function 4 not configured
"Intel 6300ESB APIC" rev 0x02 at pci0 dev 29 function 5 not configured
ehci0 at pci0 dev 29 function 7 "Intel 6300ESB USB" rev 0x02: apic 8 int 23
(ir)usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
ppb6 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0x0a
pci7 at ppb6 bus 7
bge0 at pci7 dev 2 function 0 "Broadcom BCM5705K" rev 0x03, BCM5705 A3
(0x3003)5brgphy0 at bge0 phy 1: BCM5705 10/100/1000baseT PHY, rev. 2
vga1 at pci7 dev 3 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
vendor "Compaq", unknown product 0x00d7 (class system subclass miscellaneous,
rdichpcib0 at pci0 dev 31 function 0 "Intel 6300ESB LPC" rev 0x02
pciide0 at pci0 dev 31 function 1 "Intel 6300ESB IDE" rev 0x02: DMA, channel 0
ypciide0: channel 0 disabled (no drives)
atapiscsi0 at pciide0 channel 1 drive 0
scsibus2 at atapiscsi0: 2 targets
cd0 at scsibus2 targ 0 lun 0: <PHILIPS, DVD8631, BB03> SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 3
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask 0 netmask 0 ttymask 0
pctr: user-level cycle counter enabled
dkcsum: sd0 matches BIOS drive 0x80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
WARNING: / was not properly unmounted
Automatic boot in progress: starting file system checks.
/dev/rsd0a: FREE BLK COUNT(S) WRONG IN SUPERBLK (SALVAGED)
/dev/rsd0a: SUMMARY INFORMATION BAD (SALVAGED)
/dev/rsd0a: BLK(S) MISSING IN BIT MAPS (SALVAGED)
/dev/rsd0a: 3201 files, 24821 used, 50607 free (31 frags, 6322 blocks, 0.0%
fra)/dev/rsd0a: MARKING FILE SYSTEM CLEAN
/dev/rsd0j: 56412 files, 8409319 used, 17390453 free (2949 frags, 2173438
block)/dev/rsd0j: MARKING FILE SYSTEM CLEAN
/dev/rsd0d: 3 files, 3 used, 516488 free (32 frags, 64557 blocks, 0.0%
fragment)/dev/rsd0d: MARKING FILE SYSTEM CLEAN
/dev/rsd0h: 193408 files, 1032406 used, 1548163 free (9651 frags, 192314
blocks)/dev/rsd0h: MARKING FILE SYSTEM CLEAN
/dev/rsd0e: INCORRECT BLOCK COUNT I=59912 (128 should be 0) (CORRECTED)
/dev/rsd0e: FREE BLK COUNT(S) WRONG IN SUPERBLK (SALVAGED)
/dev/rsd0e: SUMMARY INFORMATION BAD (SALVAGED)
/dev/rsd0e: BLK(S) MISSING IN BIT MAPS (SALVAGED)
/dev/rsd0e: 670 files, 15815 used, 2047198 free (214 frags, 255873 blocks,
0.0%)/dev/rsd0e: MARKING FILE SYSTEM CLEAN
/dev/rsd0g: 4 files, 5 used, 3095151 free (23 frags, 386891 blocks, 0.0%
fragme)/dev/rsd0g: MARKING FILE SYSTEM CLEAN
/dev/rsd0f: 101711 files, 11678348 used, 19282138 free (274 frags, 2410233
bloc)/dev/rsd0f: MARKING FILE SYSTEM CLEAN
setting tty flags
pf enabled
starting network
starting system logger
starting rpc daemons:
2048 MB Detected
ProLiant System BIOS - D17 (08/17/2005)
Copyright 1982, 2005 Hewlett-Packard Development Group, L.P.
... etc.
