Ok, I fired up a connection both to the wireless and wired IPs, then ran du
/ continually. The interrupts on rl0 didn't register, but the interrupts
on ral0 skyrocketed.
On Thu, Jan 24, 2013 at 1:21 AM, Tomas Bodzar <tomas.bod...@gmail.com>wrote:
> On Wed, Jan 23, 2013 at 12:43 PM, Aaron Mason <simplersolut...@gmail.com>
> wrote:
> > HI all
> >
> > Got an old HP Compaq NX9040 laptop that I've repurposed as a wireless
> > client router running OpenBSD 5.1. I've installed a Ralink RT2560
> wireless
> > card I salvaged from a broken D-Link print server. The wireless has IP
> > address 192.168.2.251, and the NIC has IP 172.16.1.254.
> >
> > My problem is if I connect to anything on the 172.16.1/24 network, even
> the
> > router's NIC address, it drops out after a few minutes. If I connect to
> > the wireless IP, it's rock solid.
> >
> > The onboard network card is a shitty Realtek 8139 card you find on most
> > laptops. Could it just be that the onboard NIC's gone to the dogs, or
> > could there be more at play here? I don't see any errors appear in dmesg
> > when the dropout occurs.
> >
>
> Try to look with netstat -i, netstat -s for interface or protocol
> errors. With vmstat -i or default screen of systat if there's not some
> interrupt storm.
>
> > Full dmesg:
> >
> > OpenBSD 5.1 (GENERIC) #160: Sun Feb 12 09:46:33 MST 2012
> > dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
> > cpu0: Intel(R) Celeron(R) M processor 1400MHz ("GenuineIntel"
> > 686-class) 1.40 GHz
> > cpu0:
> FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,TM,SBF
> > real mem = 233238528 (222MB)
> > avail mem = 219344896 (209MB)
> > mainbus0 at root
> > bios0 at mainbus0: AT/286+ BIOS, date 07/07/04, BIOS32 rev. 0 @
> > 0xfd740, SMBIOS rev. 2.31 @ 0xdf010 (28 entries)
> > bios0: vendor Hewlett-Packard version "BF.04M1" date 07/07/2004
> > bios0: Hewlett-Packard
> >
> \M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^?
> > apm0 at bios0: Power Management spec V1.2
> > acpi at bios0 function 0x0 not configured
> > pcibios0 at bios0: rev 2.1 @ 0xfd740/0x8c0
> > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf20/192 (10 entries)
> > pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
> > pcibios0: PCI bus #3 is the last bus
> > bios0: ROM list: 0xc0000/0xcc00! 0xcd000/0x1000 0xdf000/0x1000!
> 0xe0000/0x4000!
> > cpu0 at mainbus0: (uniprocessor)
> > pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> > mem address conflict 0xdf00000/0x400
> > pchb0 at pci0 dev 0 function 0 "Intel 82855GM Host" rev 0x02
> > "Intel 82855GM Memory" rev 0x02 at pci0 dev 0 function 1 not configured
> > "Intel 82855GM Config" rev 0x02 at pci0 dev 0 function 3 not configured
> > vga1 at pci0 dev 2 function 0 "Intel 82855GM Video" rev 0x02
> > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> > wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> > intagp0 at vga1
> > agp0 at intagp0: aperture at 0xe8000000, size 0x8000000
> > inteldrm0 at vga1: irq 10
> > drm0 at inteldrm0
> > "Intel 82855GM Video" rev 0x02 at pci0 dev 2 function 1 not configured
> > uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x03: irq 10
> > uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x03: irq 11
> > uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x03: couldn't
> > map interrupt
> > ehci0 at pci0 dev 29 function 7 "Intel 82801DB USB" rev 0x03: irq 11
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
> > ppb0 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x83
> > pci1 at ppb0 bus 1
> > mem address conflict 0xdf01000/0x1000
> > mem address conflict 0xdf02000/0x1000
> > rl0 at pci1 dev 0 function 0 "Realtek 8139" rev 0x10: irq 10, address
> > 00:c0:9f:57:68:77
> > rlphy0 at rl0 phy 0: RTL internal PHY
> > cbb0 at pci1 dev 1 function 0 "TI PCI1520 CardBus" rev 0x01: couldn't
> > map interrupt
> > cbb1 at pci1 dev 1 function 1 "TI PCI1520 CardBus" rev 0x01: couldn't
> > map interrupt
> > ral0 at pci1 dev 6 function 0 "Ralink RT2560" rev 0x01: irq 11,
> > address 00:13:d3:73:00:bb
> > ral0: MAC/BBP RT2560 (rev 0x04), RF RT2525
> > "TI TSB43AB21 FireWire" rev 0x00 at pci1 dev 7 function 0 not configured
> > ichpcib0 at pci0 dev 31 function 0 "Intel 82801DBM LPC" rev 0x03:
> > 24-bit timer at 3579545Hz
> > pciide0 at pci0 dev 31 function 1 "Intel 82801DBM IDE" rev 0x03: DMA,
> > channel 0 configured to compatibility, channel 1 configured to
> > compatibility
> > pciide0: channel 0 disabled (no drives)
> > atapiscsi0 at pciide0 channel 1 drive 0
> > scsibus0 at atapiscsi0: 2 targets
> > cd0 at scsibus0 targ 0 lun 0: <PHILIPS, CDRW/DVD CDD5263, UH89> ATAPI
> > 5/cdrom removable
> > cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
> > ichiic0 at pci0 dev 31 function 3 "Intel 82801DB SMBus" rev 0x03: irq 5
> > iic0 at ichiic0
> > spdmem0 at iic0 addr 0x50: 256MB DDR SDRAM non-parity PC2100CL2.5
> > auich0 at pci0 dev 31 function 5 "Intel 82801DB AC97" rev 0x03: irq 5,
> ICH4 AC97
> > ac97: codec id 0x43585430 (Conexant CXT48)
> > ac97: codec features reserved, headphone, 18 bit DAC, 18 bit ADC, No 3D
> Stereo
> > audio0 at auich0
> > "Intel 82801DB Modem" rev 0x03 at pci0 dev 31 function 6 not configured
> > usb1 at uhci0: USB revision 1.0
> > uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> > usb2 at uhci1: USB revision 1.0
> > uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> > isa0 at ichpcib0
> > isadma0 at isa0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> > pckbc0 at isa0 port 0x60/5
> > pckbd0 at pckbc0 (kbd slot)
> > pckbc0: using irq 1 for kbd slot
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pcppi0 at isa0 port 0x61
> > spkr0 at pcppi0
> > lpt0 at isa0 port 0x378/4 irq 7
> > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> > fd0 at fdc0 drive 0: density unknown
> > fd1 at fdc0 drive 1: density unknown
> > pcic0 at isa0 port 0x3e0/2 iomem 0xd0000/16384
> > pcic0 controller 0: <Intel 82365SL rev 2> has sockets A and B
> > pcmcia0 at pcic0 controller 0 socket 0
> > pcmcia1 at pcic0 controller 0 socket 1
> > pcic0: irq 14, polling enabled
> > mtrr: Pentium Pro MTRR support
> > umass0 at uhub0 port 1 configuration 1 interface 0 "USBest Technology
> > USB Mass Storage Device" rev 2.00/1.00 addr 2
> > umass0: using SCSI over Bulk-Only
> > scsibus1 at umass0: 2 targets, initiator 0
> > sd0 at scsibus1 targ 1 lun 0: <Ut163, , 1.00> SCSI2 0/direct removable
> > serial.13070163f224d3aa87aa
> > sd0: 490MB, 512 bytes/sector, 1003520 sectors
> > vscsi0 at root
> > scsibus2 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus3 at softraid0: 256 targets
> > root on sd0a (3e9e6abf58807b82.a) swap on sd0b dump on sd0b
> >
> >
> > Thanks
> >
> >
> > --
> > Aaron Mason - Programmer, open source addict
> > I've taken my software vows - for beta or for worse
> >
>
--
Aaron Mason - Programmer, open source addict
I've taken my software vows - for beta or for worse
