On Tue, Nov 20, 2012 at 12:33 AM, Imre Oolberg <i...@auul.pri.ee> wrote: > Hi! > > I am having hard time getting "NetMos Nm9835" addon PCI adapter going for > gaining two more com ports. OpenBSD 5.2-current of Nov 13 says on commodity > i386 hardware > > # dmesg > ... > puc0 at pci0 dev 8 function 0 "NetMos Nm9835" rev 0x01: ports: 2 com, 1 lpt > com3 at puc0 port 0 irq 10: ns16550a, 16 byte fifo > com4 at puc0 port 1 irq 10: ns16550a, 16 byte fifo > lpt3 at puc0 port 2 irq 10 > > and /etc/ttys has > > # cat /etc/ttys > ... > > tty03 "/usr/libexec/getty std.9600" vt200 off secure > tty04 "/usr/libexec/getty std.9600" vt200 off secure
But you need to have on here http://www.openbsd.org/faq/faq7.html#SerCon > > Issuing usual cu gives > > # cu -l /dev/cua03 -s 9600 > Connected > <and stays here> > > # cu -l /dev/cua03 -s 9600 > Connected > <and stays here> > > I would be thankful if somebody comments whether i am doing wrong something > obious or this particular device isnt supposed to work on OpenBSD although > man puc kind of says it should. (Actually haven't tried this particular > piece on anything else yet). Or some advice how to debug it to get some > meaningful information to make it possible to help me further. (And i also > tried to serve serial console from this computer on cua03 and cua04, no > luck). > > > Best regards, > > Imre > > PS This computer has two onboard com ports and they work both ways, i.e. as > serial consoles and as means to get connected to serial consoles elsewhere. > So cable should be good (so to say factory null modem cable). > > OpenBSD 5.2-current (GENERIC) #82: Tue Nov 13 13:09:22 MST 2012 > dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: AMD Duron(tm) Processor ("AuthenticAMD" 686-class, 64KB L2 cache) 698 > MHz > cpu0: > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,MMXX,3DNOW2,3DNOW > real mem = 2146955264 (2047MB) > avail mem = 2100928512 (2003MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 10/06/00, BIOS32 rev. 0 @ 0xfb350, > SMBIOS rev. 2.3 @ 0xf0800 (38 entries) > bios0: vendor Award Software International, Inc. version "6.00 PG" date > 10/06/2000 > bios0: VIA Technologies, Inc. VT8363 > apm0 at bios0: Power Management spec V1.2 (slowidle) > acpi at bios0 function 0x0 not configured > pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb7d0 > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdd00/176 (9 entries) > pcibios0: PCI Exclusive IRQs: 5 10 > pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C596A ISA" rev 0x00) > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc0000/0x10000 0xd0000/0x1000 0xd1000/0x1800 > cpu0 at mainbus0: (uniprocessor) > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 0 function 0 "VIA VT8363 Host" rev 0x03 > viaagp0 at pchb0: v2 > agp0 at viaagp0: aperture at 0xd0000000, size 0x10000000 > ppb0 at pci0 dev 1 function 0 "VIA VT8363 AGP" rev 0x00 > pci1 at ppb0 bus 1 > vga1 at pci1 dev 0 function 0 "NVIDIA Vanta" rev 0x15 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > pcib0 at pci0 dev 7 function 0 "VIA VT82C686 ISA" rev 0x22 > pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x10: ATA66, channel > 0 configured to compatibility, channel 1 configured to compatibility > wd0 at pciide0 channel 0 drive 0: <WDC WD2000JB-32EVA0> > wd0: 16-sector PIO, LBA48, 190781MB, 390719855 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4 > atapiscsi0 at pciide0 channel 1 drive 0 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, CD-RW GCE-8520B, 1.03> ATAPI > 5/cdrom removable > cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 > uhci0 at pci0 dev 7 function 2 "VIA VT83C572 USB" rev 0x10: irq 5 > uhci1 at pci0 dev 7 function 3 "VIA VT83C572 USB" rev 0x10: irq 5 > viapm0 at pci0 dev 7 function 4 "VIA VT82C686 SMBus" rev 0x30: SMI > iic0 at viapm0 > spdmem0 at iic0 addr 0x50: 1GB SDRAM registered ECC PC133CL2 > spdmem1 at iic0 addr 0x51: 1GB SDRAM registered ECC PC133CL2 > viapm0: 24-bit timer at 3579545Hz > auvia0 at pci0 dev 7 function 5 "VIA VT82C686 AC97" rev 0x20: irq 10 > ac97: codec id 0x83847609 (SigmaTel STAC9721/23) > ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D > audio0 at auvia0 > puc0 at pci0 dev 8 function 0 "NetMos Nm9835" rev 0x01: ports: 2 com, 1 lpt > com3 at puc0 port 0 irq 10: ns16550a, 16 byte fifo > com4 at puc0 port 1 irq 10: ns16550a, 16 byte fifo > lpt3 at puc0 port 2 irq 10 > em0 at pci0 dev 9 function 0 "Intel PRO/1000GT (82541GI)" rev 0x05: irq 10, > address 00:0e:0c:b0:96:b6 > em1 at pci0 dev 10 function 0 "Intel PRO/1000MT (82545GM)" rev 0x04: irq 10, > address 00:04:23:bd:17:d9 > fxp0 at pci0 dev 11 function 0 "Intel 8255x" rev 0x0c, i82550: irq 5, > address 00:03:47:9b:76:56 > inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4 > re0 at pci0 dev 12 function 0 "Realtek 8169" rev 0x10: RTL8169/8110SB > (0x1000), irq 10, address 00:06:4f:63:e3:d7 > rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 3 > isa0 at pcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > com1: console > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pcppi0 at isa0 port 0x61 > spkr0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > usb0 at uhci0: USB revision 1.0 > uhub0 at usb0 "VIA UHCI root hub" rev 1.00/1.00 addr 1 > usb1 at uhci1: USB revision 1.0 > uhub1 at usb1 "VIA UHCI root hub" rev 1.00/1.00 addr 1 > mtrr: Pentium Pro MTRR support > vscsi0 at root > scsibus1 at vscsi0: 256 targets > softraid0 at root > scsibus2 at softraid0: 256 targets > root on wd0e (24635f1cb2e8a1bb.e) swap on wd0b dump on wd0b
