I disconnected all the interfaces and after connected only one.
I'm sure that the cables are working. I tried with these options in the
hostname.ti0, each time I configured with one of these and reboot the
computer:
media 1000baseSX
media 1000baseSX mediaopt full-duplex
media autoselect
And my ifconfig -a results:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33224
groups: lo
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
ti0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:60:08:f7:19:61
media: Ethernet 1000baseSX (autoselect)
status: no carrier
pflog0: flags=0<> mtu 33224
pfsync0: flags=0<> mtu 1348
enc0: flags=0<> mtu 1536
Any idea???
Do you know about a problem with these hardware bond??
On Wed, Nov 09, 2005 at 08:24:58PM -0500, [EMAIL PROTECTED] wrote:
> Start by reviewing http://www.openbsd.org/faq/faq6.html#Intro
>
> Focus on the physical aspects of the connection before the PC/OS
> configuration stuff.
>
> Disconnect one of the nic card cables from the switch. Try to get one card
> up before the other.
>
> Do you know if the cables you are using work on another PC? Verify that
> before moving on.
>
> What does the following command reveal?
>
> ifconfig -a
>
> What do these commands reveal?
>
> cat /etc/hostname.ti0
> cat /etc/hostname.ti1
>
>
> > Hi,
> >
> > I have a problem with a dell optiplex gx520 and a 3com985 gigabit nic.
> > I installed OpenBSD 3.8 and everything is ok, I can see the nic in the
> > ifconfig, but when I connected it to the switch I didn't get the link, the
> > leds
> > in both sides are turn off, I can't get the link light.
> >
> > Do yo have any idea what can I do??
> >
> > I sent you the dmesg output. Thanks a lot
> >
> > OpenBSD 3.8 (GENERIC) #138: Sat Sep 10 15:41:37 MDT 2005
> > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
> > cpu0: Intel(R) Pentium(R) 4 CPU 2.80GHz ("GenuineIntel" 686-class) 2.80
> > GHz
> > cpu0:
> > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CF
> > LUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,CNXT-ID
> > real mem = 526520320 (514180K)
> > avail mem = 473497600 (462400K)
> > using 4278 buffers containing 26427392 bytes (25808K) of memory
> > mainbus0 (root)
> > bios0 at mainbus0: AT/286+(00) BIOS, date 08/05/05, BIOS32 rev. 0 @
> > 0xffe90
> > apm0 at bios0: Power Management spec V1.2
> > apm0: AC on, battery charge unknown
> > apm0: flags 30102 dobusy 0 doidle 1
> > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
> > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfed10/240 (13 entries)
> > pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801GB LPC" rev 0x00)
> > pcibios0: PCI bus #4 is the last bus
> > bios0: ROM list: 0xc0000/0xa800! 0xca800/0x1800
> > cpu0 at mainbus0
> > pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> > pchb0 at pci0 dev 0 function 0 "Intel 82945GP" rev 0x02
> > ppb0 at pci0 dev 1 function 0 "Intel 82945GP PCIE" rev 0x02
> > pci1 at ppb0 bus 1
> > vga1 at pci0 dev 2 function 0 vendor "Intel", unknown product 0x2772 rev
> > 0x02: a perture at 0xfeb00000, size 0x8000000
> > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> > wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> > vendor "Intel", unknown product 0x2776 (class display subclass
> > miscellaneous, re v 0x02) at pci0 dev 2 function 1 not configured
> > ppb1 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01
> > pci2 at ppb1 bus 2
> > bge0 at pci2 dev 0 function 0 "Broadcom BCM5751" rev 0x01, BCM5750 A1
> > (0x4001): irq 11 address 00:12:3f:52:6d:ca
> > brgphy0 at bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
> > ppb2 at pci0 dev 28 function 1 "Intel 82801GB PCIE" rev 0x01
> > pci3 at ppb2 bus 3
> > uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: irq 9
> > usb0 at uhci0: USB revision 1.0
> > uhub0 at usb0
> > uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
> > uhub0: 2 ports with 2 removable, self powered
> > uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: irq 5
> > usb1 at uhci1: USB revision 1.0
> > uhub1 at usb1
> > uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
> > uhub1: 2 ports with 2 removable, self powered
> > uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: irq 3
> > usb2 at uhci2: USB revision 1.0
> > uhub2 at usb2
> > uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
> > uhub2: 2 ports with 2 removable, self powered
> > uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: irq 10
> > usb3 at uhci3: USB revision 1.0
> > uhub3 at usb3
> > uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1
> > uhub3: 2 ports with 2 removable, self powered
> > ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: irq 9
> > usb4 at ehci0: USB revision 2.0
> > uhub4 at usb4
> > uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1
> > uhub4: 8 ports with 8 removable, self powered
> > ppb3 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0xe1
> > pci4 at ppb3 bus 4
> > ti0 at pci4 dev 0 function 0 "3Com 3c985" rev 0x01: irq 11 address
> > 00:60:08:f7:1 7:c4
> > ti1 at pci4 dev 2 function 0 "3Com 3c985" rev 0x01: irq 3 address
> > 00:60:08:f7:19 :61
> > pcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01
> > pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA,
> > channel 0 c onfigured to compatibility, channel 1 configured to
> > compatibility
> > atapiscsi0 at pciide0 channel 0 drive 0
> > scsibus0 at atapiscsi0: 2 targets
> > cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, CDRW/DVD GCC4482, E107> SCSI0
> > 5/cdrom r emovable
> > cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
> > pciide0: channel 1 ignored (disabled)
> > pciide1 at pci0 dev 31 function 2 "Intel 82801GB SATA" rev 0x01: DMA,
> > channel 0 configured to native-PCI, channel 1 configured to native-PCI
> > pciide1: using irq 5 for native-PCI interrupt
> > wd0 at pciide1 channel 0 drive 0: <Maxtor 6L080M0>
> > wd0: 16-sector PIO, LBA, 76293MB, 156250000 sectors
> > wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
> > "Intel 82801GB SMBus" rev 0x01 at pci0 dev 31 function 3 not configured
> > isa0 at pcib0
> > isadma0 at isa0
> > pckbc0 at isa0 port 0x60/5
> > pckbd0 at pckbc0 (kbd slot)
> > pckbc0: using irq 1 for kbd slot
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pcppi0 at isa0 port 0x61
> > midi0 at pcppi0: <PC speaker>
> > spkr0 at pcppi0
> > sysbeep0 at pcppi0
> > lpt0 at isa0 port 0x378/4 irq 7
> > npx0 at isa0 port 0xf0/16: using exception 16
> > pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > biomask f76d netmask ff6d ttymask ffef
> > pctr: user-level cycle counter enabled
> > dkcsum: wd0 matches BIOS drive 0x80
> > root on wd0a
> > rootdev=0x0 rrootdev=0x300 rawdev=0x302
> > WARNING: / was not properly unmounted
> > uhidev0 at uhub2 port 1 configuration 1 interface 0
> > uhidev0: Dell Dell USB Keyboard, rev 1.10/1.00, addr 2, iclass 3/1
> > ukbd0 at uhidev0: 8 modifier keys, 6 key codes
> > wskbd1 at ukbd0 mux 1
> > wskbd1: connecting to wsdisplay0
> > uhidev1 at uhub2 port 2 configuration 1 interface 0
> > uhidev1: Dell Dell USB Mouse, rev 1.10/29.10, addr 3, iclass 3/1
> > ums0 at uhidev1: 3 buttons and Z dir.
> > wsmouse0 at ums0 mux 0
