I have an older laptop that I recently upgraded from 4.9 to 5.1. The
laptop works fine (I'm sending from it now) as long as I don't have
the USB mouse and the PCMCIA wi(4) attached. When they are both
attached, eventually the system locks up and does not respond (no
panic, just does nothing).
I can see from the commit logs for uhidev.c that something related to
both USB and PCMCIA changed, but I'm not sure if it is relevant:
src/sys/dev/usb/uhidev.c
Remove config_activate() and DVACT_ACTIVATE. PCMCIA's the only thing
that's ever used it, and it's long since been changed to use
DVACT_{QUIESCE,SUSPEND,RESUME} instead.
It looks like this wasn't the only file modified with that commit log,
so I may not even be looking at the right file.
Thoughts on what can be done to remedy? Is there some other useful
information that I can provide?
The kernel hasn't panicked, so unless a trace is useful (FAQ says it
isn't), here's a dmesg:
OpenBSD 5.1 (GENERIC) #160: Sun Feb 12 09:46:33 MST 2012
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 598 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,MMX,FXSR,SSE
real mem = 335015936 (319MB)
avail mem = 319438848 (304MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 11/30/99, BIOS32 rev. 0 @
0xf0000, SMBIOS rev. 2.3 @ 0xfa25e (59 entries)
bios0: vendor Compaq version "1.35" date 08/08/2000
bios0: Compaq Armada M300
apm0 at bios0: Power Management spec V1.2 (BIOS managing devices)
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x1200
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfe4c0/208 (11 entries)
pcibios0: PCI Exclusive IRQs: 11
pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371AB PIIX4 ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x10000 0xd0000/0x1800
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82443BX" rev 0x03
cbb0 at pci0 dev 4 function 0 "TI PCI1211 CardBus" rev 0x00: irq 11
vga1 at pci0 dev 5 function 0 "ATI Mach64" rev 0xdc
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
piixpcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <TOSHIBA MK3018GAS>
wd0: 16-sector PIO, LBA, 28615MB, 58605120 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 11
piixpm0 at pci0 dev 7 function 3 "Intel 82371AB Power" rev 0x03: SMI
iic0 at piixpm0
spdmem0 at iic0 addr 0x50: 256MB SDRAM non-parity PC100CL2
maestro0 at pci0 dev 8 function 0 "ESS Maestro 2E" rev 0x10: irq 11
ac97: codec id 0x83847609 (SigmaTel STAC9721/23)
ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D
audio0 at maestro0
fxp0 at pci0 dev 9 function 0 "Intel 8255x" rev 0x09, i82559S: irq 11,
address 00:d0:59:15:66:99
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
"AT&T/Lucent LTMODEM" rev 0x00 at pci0 dev 9 function 1 not configured
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x8, lattimer 0x20
pcmcia0 at cardslot0
isa0 at piixpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com2 at isa0 port 0x3e8/8 irq 5: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pms0: Synaptics touchpad, firmware 5.1
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
mtrr: Pentium Pro MTRR support
uhidev0 at uhub0 port 1 configuration 1 interface 0 "Logitech USB-PS/2
Optical Mouse" rev 2.00/13.20 addr 2
uhidev0: iclass 3/1
ums0 at uhidev0: 4 buttons, Z dir
wsmouse1 at ums0 mux 0
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
scsibus1 at softraid0: 256 targets
root on wd0a (d6952a422d689fb0.a) swap on wd0b dump on wd0b
WARNING: / was not properly unmounted
wi0 at pcmcia0 function 0 "The Linksys Group, Inc., Instant Wireless
Network PC Card, ISL37300P" port 0xa000/64
wi0: PRISM3 ISL37300P (0x801b), Firmware 1.1.0 (primary), 1.4.2
(station), address 00:06:25:15:f5:1f
wsmouse1 detached
ums0 detached
uhidev0 detached
Thanks,
Lu-
