On p, jún 29, 2012 at 09:30:45 +0200, LEVAI Daniel wrote:
> Hi!
>
> I'm using a SIL 3512A (BIOS ver. 4.3.79) SATA raid card with two disks
> connected to it.
> When I'm starting an I/O intensive archive unpacking from wd0 to wd1, I
> get DMA errors on the console. If I unpack from wd0 -> wd0, then it
> seems fine. I've replaced/switched cables and replaced wd1 too.
> I can not get a dmesg at the moment, sorry, but I'll post it later when
> I get to the machine. It is an old Pentium 4 2.4 GHz and runs 5.1-base.
[...]
Hi!
Here is the promised dmesg. I've updated the cards BIOS since, but still
no luck.
Thanks for any input.
Also there are new error messages after the BIOS update:
wd1d: aborted command writing fsbn 48938080 of 48938080-48938111 (wd1 bn
258653472; cn 256600 tn 10 sn 42), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 48961216 of 48961216-48961247 (wd1 bn
258676608; cn 256623 tn 9 sn 57), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 48976960 of 48976960-48976991 (wd1 bn
258692352; cn 256639 tn 3 sn 51), retrying
wd1: soft error (corrected)
wd1(pciide0:1:0): timeout
type: ata
c_bcount: 16384
c_skip: 0
pciide0:1:0: bus-master DMA error: missing interrupt, status=0x21
wd1d: device timeout writing fsbn 48990240 of 48990240-48990271 (wd1 bn
258705632; cn 256652 tn 6 sn 38), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49046400 of 49046400-49046431 (wd1 bn
258761792; cn 256708 tn 2 sn 2), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49058976 of 49058976-49059007 (wd1 bn
258774368; cn 256720 tn 9 sn 41), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49093760 of 49093760-49093791 (wd1 bn
258809152; cn 256755 tn 1 sn 49), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49096640 of 49096640-49096671 (wd1 bn
258812032; cn 256757 tn 15 sn 31), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49110784 of 49110784-49110815 (wd1 bn
258826176; cn 256772 tn 0 sn 0), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49121504 of 49121504-49121535 (wd1 bn
258836896; cn 256782 tn 10 sn 10), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49359616 of 49359616-49359647 (wd1 bn
259075008; cn 257018 tn 13 sn 45), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49377728 of 49377728-49377759 (wd1 bn
259093120; cn 257036 tn 13 sn 13), retrying
wd1: soft error (corrected)
Daniel
dmesg:
OpenBSD 5.1 (GENERIC) #160: Sun Feb 12 09:46:33 MST 2012
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) 4 CPU 2.40GHz ("GenuineIntel" 686-class) 2.42 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,CNXT-ID
real mem = 2146955264 (2047MB)
avail mem = 2101735424 (2004MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 11/05/02, BIOS32 rev. 0 @ 0xfdb60, SMBIOS
rev. 2.3 @ 0xf0630 (32 entries)
bios0: vendor American Megatrends Inc. version "V1.2 11" date 11/05/2002
bios0: MICRO-STAR INC. MS-6704
acpi0 at bios0: rev 0
acpi0: sleep states S0 S1 S4 S5
acpi0: tables DSDT FACP APIC
acpi0: wakeup devices USB1(S3) USB2(S3) USB3(S3) EHCI(S3) ICHB(S4) PS2M(S4)
PS2K(S4) UAR1(S4) MC9_(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 133MHz
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 2 (ICHB)
acpicpu0 at acpi0
acpipwrres0 at acpi0: URP1
acpipwrres1 at acpi0: URP2
acpipwrres2 at acpi0: FDDP
acpipwrres3 at acpi0: LPTP
acpibtn0 at acpi0: PWRB
bios0: ROM list: 0xc0000/0xd000 0xcd000/0x4800 0xd1800/0x1000 0xe0000/0x1000
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82845G Host" rev 0x02
intelagp0 at pchb0
agp0 at intelagp0: aperture at 0xe0000000, size 0x4000000
ppb0 at pci0 dev 1 function 0 "Intel 82845G AGP" rev 0x02
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon 9600" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
radeondrm0 at vga1: apic 2 int 16
drm0 at radeondrm0
"ATI Radeon 9600 XT Sec" rev 0x00 at pci1 dev 0 function 1 not configured
uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x02: apic 2 int 16
uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x02: apic 2 int 19
uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x02: apic 2 int 18
ehci0 at pci0 dev 29 function 7 "Intel 82801DB USB" rev 0x02: apic 2 int 23
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb1 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x82
pci2 at ppb1 bus 2
vge0 at pci2 dev 1 function 0 "VIA VT612x" rev 0x11: apic 2 int 17, address
00:04:e2:76:98:d0
ciphy0 at vge0 phy 1: CS8201 10/100/1000TX PHY, rev. 1
pciide0 at pci2 dev 3 function 0 "CMD Technology SiI3512 SATA" rev 0x01: DMA
pciide0: using apic 2 int 19 for native-PCI interrupt
pciide0: port 0: device present, speed: 1.5Gb/s
wd0 at pciide0 channel 0 drive 0: <ST3250310AS>
wd0: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
wd0(pciide0:0:0): using BIOS timings, Ultra-DMA mode 5
pciide0: port 1: device present, speed: 1.5Gb/s
wd1 at pciide0 channel 1 drive 0: <SAMSUNG HD501LJ>
wd1: 16-sector PIO, LBA48, 476940MB, 976773168 sectors
wd1(pciide0:1:0): using BIOS timings, Ultra-DMA mode 7
em0 at pci2 dev 4 function 0 "Intel PRO/1000GT (82541GI)" rev 0x05: apic 2 int
16, address 00:1b:21:0a:aa:12
ichpcib0 at pci0 dev 31 function 0 "Intel 82801DB LPC" rev 0x02
pciide1 at pci0 dev 31 function 1 "Intel 82801DB IDE" rev 0x02: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide1 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GSA-4120B, A115> ATAPI 5/cdrom
removable
cd0(pciide1:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide1: channel 1 ignored (disabled)
ichiic0 at pci0 dev 31 function 3 "Intel 82801DB SMBus" rev 0x02: apic 2 int 17
iic0 at ichiic0
iic0: addr 0x2f 00=00 02=0f 03=00 04=00 06=0f 07=00 08=00 0a=06 0b=00 0c=00
0d=07 0e=85 0f=00 10=c4 11=10 12=00 13=60 words 00=00ff 01=ffff 02=0fff 03=00ff
04=00ff 05=ffff 06=0fff 07=00ff
spdmem0 at iic0 addr 0x50: 1GB DDR SDRAM non-parity PC3200CL3.0
spdmem1 at iic0 addr 0x51: 1GB DDR SDRAM non-parity PC3200CL3.0
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
wbsio0 at isa0 port 0x2e/2: W83627HF rev 0x17
lm1 at wbsio0 port 0x290/8: W83627HF
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
mtrr: Pentium Pro MTRR support
umass0 at uhub0 port 2 configuration 1 interface 0 "USBest Technology USB Mass
Storage Device" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <UDISK, PDU01-2G 7BH2.0, 0.00> SCSI2 0/direct
removable serial.130701630000000007EE
sd0: 1927MB, 512 bytes/sector, 3948543 sectors
uhidev0 at uhub3 port 2 configuration 1 interface 0 "Trust Optical Mouse" rev
1.10/1.00 addr 2
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on wd0a (69dbc259cb64de66.a) swap on wd0b dump on wd0b
WARNING: / was not properly unmounted
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
pppoe0: received unexpected PADO
vge0: watchdog timeout
wd1d: aborted command writing fsbn 48938080 of 48938080-48938111 (wd1 bn
258653472; cn 256600 tn 10 sn 42), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 48961216 of 48961216-48961247 (wd1 bn
258676608; cn 256623 tn 9 sn 57), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 48976960 of 48976960-48976991 (wd1 bn
258692352; cn 256639 tn 3 sn 51), retrying
wd1: soft error (corrected)
wd1(pciide0:1:0): timeout
type: ata
c_bcount: 16384
c_skip: 0
pciide0:1:0: bus-master DMA error: missing interrupt, status=0x21
wd1d: device timeout writing fsbn 48990240 of 48990240-48990271 (wd1 bn
258705632; cn 256652 tn 6 sn 38), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49046400 of 49046400-49046431 (wd1 bn
258761792; cn 256708 tn 2 sn 2), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49058976 of 49058976-49059007 (wd1 bn
258774368; cn 256720 tn 9 sn 41), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49093760 of 49093760-49093791 (wd1 bn
258809152; cn 256755 tn 1 sn 49), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49096640 of 49096640-49096671 (wd1 bn
258812032; cn 256757 tn 15 sn 31), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49110784 of 49110784-49110815 (wd1 bn
258826176; cn 256772 tn 0 sn 0), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49121504 of 49121504-49121535 (wd1 bn
258836896; cn 256782 tn 10 sn 10), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49359616 of 49359616-49359647 (wd1 bn
259075008; cn 257018 tn 13 sn 45), retrying
wd1: soft error (corrected)
wd1d: aborted command writing fsbn 49377728 of 49377728-49377759 (wd1 bn
259093120; cn 257036 tn 13 sn 13), retrying
wd1: soft error (corrected)
OpenBSD 5.1 (GENERIC) #160: Sun Feb 12 09:46:33 MST 2012
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) 4 CPU 2.40GHz ("GenuineIntel" 686-class) 2.42 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,CNXT-ID
real mem = 2146955264 (2047MB)
avail mem = 2101735424 (2004MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 11/05/02, BIOS32 rev. 0 @ 0xfdb60, SMBIOS
rev. 2.3 @ 0xf0630 (32 entries)
bios0: vendor American Megatrends Inc. version "V1.2 11" date 11/05/2002
bios0: MICRO-STAR INC. MS-6704
acpi0 at bios0: rev 0
acpi0: sleep states S0 S1 S4 S5
acpi0: tables DSDT FACP APIC
acpi0: wakeup devices USB1(S3) USB2(S3) USB3(S3) EHCI(S3) ICHB(S4) PS2M(S4)
PS2K(S4) UAR1(S4) MC9_(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 133MHz
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 2 (ICHB)
acpicpu0 at acpi0
acpipwrres0 at acpi0: URP1
acpipwrres1 at acpi0: URP2
acpipwrres2 at acpi0: FDDP
acpipwrres3 at acpi0: LPTP
acpibtn0 at acpi0: PWRB
bios0: ROM list: 0xc0000/0xd000 0xcd000/0x4800 0xd1800/0x1000 0xe0000/0x1000
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82845G Host" rev 0x02
intelagp0 at pchb0
agp0 at intelagp0: aperture at 0xe0000000, size 0x4000000
ppb0 at pci0 dev 1 function 0 "Intel 82845G AGP" rev 0x02
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon 9600" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
radeondrm0 at vga1: apic 2 int 16
drm0 at radeondrm0
"ATI Radeon 9600 XT Sec" rev 0x00 at pci1 dev 0 function 1 not configured
uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x02: apic 2 int 16
uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x02: apic 2 int 19
uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x02: apic 2 int 18
ehci0 at pci0 dev 29 function 7 "Intel 82801DB USB" rev 0x02: apic 2 int 23
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb1 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x82
pci2 at ppb1 bus 2
vge0 at pci2 dev 1 function 0 "VIA VT612x" rev 0x11: apic 2 int 17, address
00:04:e2:76:98:d0
ciphy0 at vge0 phy 1: CS8201 10/100/1000TX PHY, rev. 1
pciide0 at pci2 dev 3 function 0 "CMD Technology SiI3512 SATA" rev 0x01: DMA
pciide0: using apic 2 int 19 for native-PCI interrupt
pciide0: port 0: device present, speed: 1.5Gb/s
wd0 at pciide0 channel 0 drive 0: <ST3250310AS>
wd0: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
wd0(pciide0:0:0): using BIOS timings, Ultra-DMA mode 5
pciide0: port 1: device present, speed: 1.5Gb/s
em0 at pci2 dev 4 function 0 "Intel PRO/1000GT (82541GI)" rev 0x05: apic 2 int
16, address 00:1b:21:0a:aa:12
ichpcib0 at pci0 dev 31 function 0 "Intel 82801DB LPC" rev 0x02
pciide1 at pci0 dev 31 function 1 "Intel 82801DB IDE" rev 0x02: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide1 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GSA-4120B, A115> ATAPI 5/cdrom
removable
cd0(pciide1:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide1: channel 1 ignored (disabled)
ichiic0 at pci0 dev 31 function 3 "Intel 82801DB SMBus" rev 0x02: apic 2 int 17
iic0 at ichiic0
iic0: addr 0x2f 00=00 02=0f 03=00 04=00 06=0f 07=00 08=00 0a=06 0b=00 0c=00
0d=07 0e=85 0f=00 10=c4 11=10 12=00 13=60 words 00=00ff 01=ffff 02=0fff 03=00ff
04=00ff 05=ffff 06=0fff 07=00ff
spdmem0 at iic0 addr 0x50: 1GB DDR SDRAM non-parity PC3200CL3.0
spdmem1 at iic0 addr 0x51: 1GB DDR SDRAM non-parity PC3200CL3.0
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
wbsio0 at isa0 port 0x2e/2: W83627HF rev 0x17
lm1 at wbsio0 port 0x290/8: W83627HF
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
mtrr: Pentium Pro MTRR support
uhidev0 at uhub3 port 2 configuration 1 interface 0 "Trust Optical Mouse" rev
1.10/1.00 addr 2
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on wd0a (69dbc259cb64de66.a) swap on wd0b dump on wd0b
WARNING: / was not properly unmounted
umass0 at uhub0 port 1 configuration 1 interface 0 "USBest Technology USB Mass
Storage Device" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus3 at umass0: 2 targets, initiator 0
sd0 at scsibus3 targ 1 lun 0: <UDISK, PDU01-2G 7BH2.0, 0.00> SCSI2 0/direct
removable serial.130701630000000007EE
sd0: 1927MB, 512 bytes/sector, 3948543 sectors
--
LÉVAI Dániel
PGP key ID = 0x83B63A8F
Key fingerprint = DBEC C66B A47A DFA2 792D 650C C69B BE4C 83B6 3A8F
