> > > > I got this Mac Mini on my hands, and I would like to install
> > > > current/macppc on it. According to
> > > > http://www.openbsd.org/macppc.html#hardware
> > > > the following MicMini's are supported:
> > > >
> > > > Mac mini (PowerMac10,1)
> > > > Mac mini (Late 2005 (PowerMac10,2))
> > > >
> > > > My model number is A1103. A quick search suggests
> > > > that it's the same as "PowerMac10,1" - is that correct?
> > > >
> > > > If so, it should be supported. My problem is it won't
> > > > boot from install51.iso. I hold the [c] key while booting up,
> > > > but it still boots into the MacOSX 10.5.8 that is currently
> > > > installed on the disk, instead of booting from the CD.
> > > >
> > > An other way to boot from the CD would be to get into the openfirmware
> > > prompt holding cmd+alt+O+F when your machine starts, then type:
> > >
> > > boot cd:,\\:tbxi
> >
> > I only have the minimac, not the other apple paraphernalia;
> > in particular, I don't have an apple keyboard, so there's
> > no way for me to press "cmd+alt+o+f". According to INSTALL.macppc,
> > it's "Command + Option + O + F" actually; is there a way to
> > do that on a non-apple keyboard? I have the usual PC keyboard
> > attached to it via USB.
>
> Win+Alt+O+F then.
This get me to the Open Firmware prompt - thank you.
In Open Firmware, I am trying to boot off the install CD.
Strangely,
boot cd:,ofwboot /5.1/macppc/bsd.rd
doesn't work:
MAC-PARTS: bad partition can't OPEN cd:,ofwboot
Can't open device or file
ok
but
boot hd:,ofwboot /5.1/macppc/bsd.rd
does boot the CD (note the diference - "cd" vs "hd").
I understand that "hd" and "cd" are just devaliases; in my case,
hd /pci@f4000000/ata-6@d/disk@0
cd /pci@f4000000/ata-6@d/disk@1
Does that mean that those device aliases are somehow mixed up?
Anyway, once started, the installation goes through smoothly.
Unlike ofw, the install script recognizes 'cd' as the CD correctly
(when choosing where to install the sets from). I chose MBR instead
of HFS, as I do not intend to dual boot MacOSX.
Now, my last problem is that I cannot boot the installed /bsd.
I understand that OFW needs to be configured to boot it, but
I run into the same problem as during the installation: the expected
boot hd:,ofwboot /bsd
apparently tries to boot from the CD - it starts spinning, and fails with
open /pci@f4000000/ata-6@d/disk@0/bsd: No such file or directory
I have tried
boot ide0:,ofwboot /bsd
boot ide1:,ofwboot /bsd
boot ultra0:,ofwboot /bsd
boot ultra1:,ofwboot /bsd
- all of them fail with Can't open device or file.
The only thing that I can get to boot is
boot hd:,ofwboot /5.1/macppc/bsd
i.e., the kernel from the install CD. Once booted, the system is there
as I installed it and runs fine.
Obviously, I would like to boot the /bsd I installed on disk.
Isuppose this is an Open Firmware problem rather then an OpenBSD
problem. Namely, Idon't know how to address the harddisk I installed
on from within open firmware. Can someone enlighten me please?
Jan
[ using 496832 bytes of bsd ELF symbol table ]
console out [ATY,RockHopper2_A]console in [keyboard] , using USB
using parent ATY,RockHopper2Paren:: memaddr 98000000 size 8000000, : consaddr
9c008000, : ioaddr 90020000, size 20000: memtag 8000, iotag 8000: width 1440
linebytes 1536 height 900 depth 8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2012 OpenBSD. All rights reserved. http://www.OpenBSD.org
uvm_km_kmem_grow: grown to 0xee000000
OpenBSD 5.1-current (GENERIC) #201: Wed Jun 6 14:56:55 MDT 2012
dera...@macppc.openbsd.org:/usr/src/sys/arch/macppc/compile/GENERIC
real mem = 1073741824 (1024MB)
avail mem = 1032257536 (984MB)
mainbus0 at root: model PowerMac10,2
cpu0 at mainbus0: 7447A (Revision 0x102): 1499 MHz: 512KB L2 cache
mem0 at mainbus0
spdmem0 at mem0: 1GB DDR SDRAM non-parity PC3200CL3.0
memc0 at mainbus0: uni-n
"hw-clock" at memc0 not configured
kiic0 at memc0 offset 0xf8001000
iic0 at kiic0
mpcpcibr0 at mainbus0 pci: uni-north, Revision 0xff
pci0 at mpcpcibr0 bus 0
pchb0 at pci0 dev 11 function 0 "Apple UniNorth AGP" rev 0x00
vgafb0 at pci0 dev 16 function 0 "ATI Radeon 9200" rev 0x01, mmio
wsdisplay0 at vgafb0 mux 1: console (std, vt100 emulation)
mpcpcibr1 at mainbus0 pci: uni-north, Revision 0x5
pci1 at mpcpcibr1 bus 0
pchb1 at pci1 dev 11 function 0 "Apple UniNorth PCI" rev 0x00
bwi0 at pci1 dev 18 function 0 "Broadcom BCM4318" rev 0x02: irq 52, address
00:11:24:bf:cb:2a
macobio0 at pci1 dev 23 function 0 "Apple Intrepid" rev 0x00
openpic0 at macobio0 offset 0x40000: version 0x4614 feature 3f0302 LE
macgpio0 at macobio0 offset 0x50
"modem-reset" at macgpio0 offset 0x1d not configured
"modem-power" at macgpio0 offset 0x1c not configured
macgpio1 at macgpio0 offset 0x9 irq 47
"programmer-switch" at macgpio0 offset 0x11 not configured
"gpio5" at macgpio0 offset 0x6f not configured
"gpio6" at macgpio0 offset 0x70 not configured
"extint-gpio15" at macgpio0 offset 0x67 not configured
"escc-legacy" at macobio0 offset 0x12000 not configured
zsc0 at macobio0 offset 0x13000: irq 22,23
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
aoa0 at macobio0 offset 0x10000: irq 30,1,2
audio0 at aoa0
"timer" at macobio0 offset 0x15000 not configured
adb0 at macobio0 offset 0x16000 irq 25: via-pmu, 0 targets
apm0 at adb0: battery flags 0x0, 0% charged
piic0 at adb0
iic1 at piic0
maxtmp0 at iic1 addr 0xc8: max6642
kiic1 at macobio0 offset 0x18000
iic2 at kiic1
wdc0 at macobio0 offset 0x20000 irq 24: DMA
ohci0 at pci1 dev 24 function 0 "Apple Intrepid USB" rev 0x00: couldn't map
interrupt
ohci1 at pci1 dev 25 function 0 "Apple Intrepid USB" rev 0x00: couldn't map
interrupt
ohci2 at pci1 dev 26 function 0 "Apple Intrepid USB" rev 0x00: irq 29, version
1.0, legacy support
ohci3 at pci1 dev 27 function 0 "NEC USB" rev 0x43: irq 63, version 1.0
ohci4 at pci1 dev 27 function 1 "NEC USB" rev 0x43: irq 63, version 1.0
ehci0 at pci1 dev 27 function 2 "NEC USB" rev 0x04: irq 63
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "NEC EHCI root hub" rev 2.00/1.00 addr 1
usb1 at ohci2: USB revision 1.0
uhub1 at usb1 "Apple OHCI root hub" rev 1.00/1.00 addr 1
usb2 at ohci3: USB revision 1.0
uhub2 at usb2 "NEC OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci4: USB revision 1.0
uhub3 at usb3 "NEC OHCI root hub" rev 1.00/1.00 addr 1
mpcpcibr2 at mainbus0 pci: uni-north, Revision 0x6
pci2 at mpcpcibr2 bus 0
pchb2 at pci2 dev 11 function 0 "Apple UniNorth PCI" rev 0x00
kauaiata0 at pci2 dev 13 function 0 "Apple Intrepid ATA" rev 0x00
wdc1 at kauaiata0 irq 39: DMA
atapiscsi0 at wdc1 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <MATSHITA, DVD-R UJ-825, DAND> ATAPI 5/cdrom
removable
wd0 at wdc1 channel 0 drive 1: <ST9808211A>
wd0: 16-sector PIO, LBA, 76319MB, 156301488 sectors
cd0(wdc1:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4
wd0(wdc1:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4
"Apple UniNorth Firewire" rev 0x81 at pci2 dev 14 function 0 not configured
gem0 at pci2 dev 15 function 0 "Apple Uni-N2 GMAC" rev 0x80: irq 41, address
00:14:51:17:42:34
bmtphy0 at gem0 phy 0: BCM5221 100baseTX PHY, rev. 4
uhidev0 at uhub1 port 1 configuration 1 interface 0 "Apple Computer HID-proxy"
rev 2.00/19.65 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub1 port 1 configuration 1 interface 1 "Apple Computer HID-proxy"
rev 2.00/19.65 addr 2
uhidev1: iclass 3/1
ums0 at uhidev1: 5 buttons
wsmouse0 at ums0 mux 0
uhidev2 at uhub2 port 1 configuration 1 interface 0 "Chicony USB Keyboard" rev
1.10/1.02 addr 2
uhidev2: iclass 3/1
ukbd1 at uhidev2: 8 modifier keys, 6 key codes
wskbd1 at ukbd1 mux 1
wskbd1: connecting to wsdisplay0
uhidev3 at uhub2 port 1 configuration 1 interface 1 "Chicony USB Keyboard" rev
1.10/1.02 addr 2
uhidev3: iclass 3/0, 3 report ids
uhid0 at uhidev3 reportid 1: input=1, output=0, feature=0
uhid1 at uhidev3 reportid 2: input=1, output=0, feature=2
uhid2 at uhidev3 reportid 3: input=3, output=0, feature=0
uhidev4 at uhub3 port 1 configuration 1 interface 0 "Genius Optical Mouse" rev
1.10/1.00 addr 2
uhidev4: iclass 3/1
ums1 at uhidev4: 3 buttons, Z dir
wsmouse1 at ums1 mux 0
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
bootpath: /pci@f4000000/ata-6@d/disk:/5.1/macppc/bsd
root on wd0a (f3de9c2b3de3dd62.a) swap on wd0b dump on wd0b
