dmesg attached, maybe that will give anyone an idea.
CPU is running at 188 MHz, but it's actually an underclocked 200MHz Pentium
MMX - I never managed to get the jumpers straight, and i figured running it
at a bit lower speed is safer than making it run too fast.
viq
OpenBSD 3.7-current (GENERIC) #232: Thu Jul 7 15:39:44 MDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium/MMX ("GenuineIntel" 586-class) 188 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX
cpu0: F00F bug workaround installed
real mem = 133799936 (130664K)
avail mem = 115515392 (112808K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(fe) BIOS, date 10/28/97, BIOS32 rev. 0 @ 0xfb440
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb8b8
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfddb0/128 (6 entries)
pcibios0: PCI Exclusive IRQs: 9 10 11
pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371SB ISA" rev 0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x800
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82439TX System" rev 0x01
pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x01
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <ST340016A>
wd0: 16-sector PIO, LBA, 32253MB, 66055248 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
wd1 at pciide0 channel 1 drive 0: <WDC AC21600H>
wd1: 16-sector PIO, LBA, 1549MB, 3173184 sectors
atapiscsi0 at pciide0 channel 1 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, CD-ROM GCR-8523B, 1.00> SCSI0 5/cdrom
removable
wd1(pciide0:1:0): using PIO mode 4, DMA mode 2
cd0(pciide0:1:1): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Intel 82371AB Power" rev 0x01 at pci0 dev 7 function 3 not configured
ne3 at pci0 dev 13 function 0 "Realtek 8029" rev 0x00: irq 10
ne3: address 00:c0:df:f8:6c:48
vga1 at pci0 dev 14 function 0 "S3 Trio32/64" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
rl0 at pci0 dev 15 function 0 "Realtek 8139" rev 0x10: irq 9 address
00:0a:cd:06:2d:c1
rlphy0 at rl0 phy 0: RTL internal phy
xl0 at pci0 dev 16 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 11,
address 00:04:75:9d:89:e5
exphy0 at xl0 phy 24: 3Com internal media interface
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask f965 netmask ff65 ttymask ffe7
pctr: 586-class performance counters and user-level cycle counter enabled
dkcsum: wd0 matched BIOS disk 80
dkcsum: wd1 matched BIOS disk 81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
----------------------------------------------------------------------
Najnowsze wiadomosci!!! >>> http://link.interia.pl/f18a0
