> I try setup my card DWL-G520 in my OpenBSD 3.7, but not working.
Try -current
ap>$ sudo ifconfig ath0 inet 10.10.10.1 255.255.255.0 NONE mediaopt hostap mode
11b chan 1 nwid "the daddy" debug up
ath0: begin active scan
ath0: sending probe_req to ff:ff:ff:ff:ff:ff on channel 2
ar5k_ar5212_nic_wakeup: failed to resume the AR5212 (again)
ath0: unable to reset hardware; hal status 2
ath0: creating ibss
ath0: synchronized with 00:0d:88:8a:d8:6f ssid "the daddy" channel 1 start 11M
client>$ sudo ifconfig iwi0 10.10.10.2 255.255.255.0 NONE nwid "the daddy" up
client>$ ifconfig -M iwi0
iwi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:12:f0:1d:34:7c
media: IEEE802.11 autoselect (DS11)
status: active
ieee80211: nwid "the daddy" chan 1 bssid 00:0d:88:8a:d8:6f 100dBm
inet6 fe80::212:f0ff:fe1d:347c%iwi0 prefixlen 64 scopeid 0x1
inet 10.10.10.2 netmask 0xff000000 broadcast 255.255.255.0
ap>$ ath0: received auth from 00:12:f0:1d:34:7c rssi 36
ath0: sending auth to 00:12:f0:1d:34:7c on channel 1
ath0: station 00:12:f0:1d:34:7c already authenticated (open)
ath0: received assoc_req from 00:12:f0:1d:34:7c rssi 46
ath0: sending assoc_resp to 00:12:f0:1d:34:7c on channel 1
ap>$ ifconfig -M ath0
ath0: flags=8867<UP,BROADCAST,DEBUG,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST> mtu
1500
lladdr 00:0d:88:8a:d8:6f
media: IEEE802.11 autoselect mode 11b hostap
status: active
ieee80211: nwid "the daddy" chan 1 bssid 00:0d:88:8a:d8:6f
lladdr 00:12:f0:1d:34:7c 38dB 11M assoc
inet6 fe80::20d:88ff:fe8a:d86f%ath0 prefixlen 64 scopeid 0x7
inet 10.10.10.1 netmask 0xff000000 broadcast 255.255.255.0
client>$ scp ap:/bsd ./
bsd 100% 5073KB 211.4KB/s 00:24
ap:
OpenBSD 3.7-current (GENERIC) #7: Sat Jun 4 19:21:50 BST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD" 486-class)
cpu0: FPU
real mem = 66691072 (65128K)
avail mem = 53403648 (52152K)
using 839 buffers containing 3436544 bytes (3356K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 20/21/13, BIOS32 rev. 0 @ 0xf00c0
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc8000/0xa000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00: product 0
stepping 1.1, CPU clock 100MHz, reset 40<SCP>
gpio0 at elansc0: 32 pins
cbb0 at pci0 dev 9 function 0 "Texas Instruments PCI1410 CardBus" rev 0x02: irq
10
sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00: DP83815D, irq 11,
address 00:00:24:c1:84:e0
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00: DP83815D, irq 5,
address 00:00:24:c1:84:e1
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer 0x3f
pcmcia0 at cardslot0
isa0 at mainbus0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
wdc0 at isa0 port 0x1f0/8 irq 14
wd0 at wdc0 channel 0 drive 0: <TOSHIBA THNCF032MBA>
wd0: 1-sector PIO, LBA, 31MB, 63488 sectors
wd0(wdc0:0:0): using BIOS timings
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask f7c5 netmask ffe5 ttymask ffe7
pctr: no performance counters in CPU
ath0 at cardbus0 dev 0 function 0 "Atheros Communications, Inc.,
AR5001-0000-0000, Wireless LAN Reference Card": irq 10
ath0: AR5212 5.6 phy 4.1 rf2112 4.5, ETSI4W, address 00:0d:88:8a:d8:6f
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
client:
OpenBSD 3.7-current (GENERIC) #7: Sat Jun 4 19:21:50 BST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Celeron(R) M processor 1400MHz ("GenuineIntel" 686-class) 1.40
GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,TM,SBF
real mem = 258449408 (252392K)
avail mem = 229019648 (223652K)
using 3180 buffers containing 13025280 bytes (12720K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(28) BIOS, date 02/21/05, BIOS32 rev. 0 @ 0xfd740
pcibios0 at bios0: rev 2.1 @ 0xfd6d0/0x930
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdeb0/256 (14 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xd000! 0xcd000/0x1000 0xce000/0x1000 0xdc000/0x4000!
0xe0000/0x10000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82852GM Hub-PCI" rev 0x02
"Intel 82852GM Memory" rev 0x02 at pci0 dev 0 function 1 not configured
"Intel 82852GM Configuration" rev 0x02 at pci0 dev 0 function 3 not configured
vga1 at pci0 dev 2 function 0 "Intel 82852GM AGP" rev 0x02: aperture at
0xe0000000, size 0x8000000
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"Intel 82852GM AGP" rev 0x02 at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x01: irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x01: irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801DB USB" rev 0x01: irq 11
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
ppb0 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x81
pci1 at ppb0 bus 1
cbb0 at pci1 dev 0 function 0 "Texas Instruments PCI1510 CardBus" rev 0x00: irq
11
iwi0 at pci1 dev 2 function 0 "Intel PRO/Wireless 2200BG" rev 0x05: irq 11,
address 00:12:f0:1d:34:7c
fxp0 at pci1 dev 8 function 0 "Intel PRO/100 VE" rev 0x81: irq 11, address
00:0a:e4:30:aa:67
inphy0 at fxp0 phy 1: i82562ET 10/100 PHY, rev. 0
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0 cacheline 0x8, lattimer 0xb0
pcmcia0 at cardslot0
ichpcib0 at pci0 dev 31 function 0 "Intel 82801DBM LPC" rev 0x01: SpeedStep
pciide0 at pci0 dev 31 function 1 "Intel 82801DBM IDE" rev 0x01: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <ST94011A>
wd0: 16-sector PIO, LBA48, 38154MB, 78140160 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, RW/DVD GCC-4241N, 1.04> SCSI0 5/cdrom
removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
"Intel 82801DB SMBus" rev 0x01 at pci0 dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5 "Intel 82801DB AC97" rev 0x01: irq 11, ICH4
AC97
ac97: codec id 0x41445374 (Analog Devices AD1981B)
ac97: codec features headphone, 20 bit DAC, No 3D Stereo
audio0 at auich0
"Intel 82801DB Modem" rev 0x01 at pci0 dev 31 function 6 not configured
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt2 at isa0 port 0x3bc/4: polled
npx0 at isa0 port 0xf0/16: using exception 16
biomask effd netmask effd ttymask ffff
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
ath0 at cardbus0 dev 0 function 0 "At(ero3 Co-mun)cat)ons, In#.,
A\^R5001-0000-0000, \^Wire,ess LAN Ref%ren#e C!rd": irq 11
ar5k_ar5212_nic_wakeup: failed to reset the AR5212 + PCI chipset
ath0: unable to attach hardware; HAL status 22
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
