Re: Hang using generic.mp with ami0

Marco Peereboom Wed, 25 May 2005 21:25:59 -0700

Quite useless.  The least you could have done is send a dmesg.


On May 25, 2005, at 10:21 PM, JR Dalrymple wrote:

This sounds similar to a problem I was having, kind of. One of the odd

things about the problem I was having though was that when I bootedandredirected the console to the serial port so I could capture thetrace etc.

it wouldn't do it.

That doesn't help, but it is what I have to say.

JR

-----Original Message-----

From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] OnBehalf Of

Marco Peereboom
Sent: Wednesday, May 25, 2005 4:43 PM
To: Steve Shockley
Cc: Miscellaneous OBSD
Subject: Re: Hang using generic.mp with ami0

hmmm very odd.  Let me try to reproduce.

On May 25, 2005, at 6:59 PM, Steve Shockley wrote:

I've just set up a Compaq Proliant 6500 with OpenBSD 3.7-release.
It works fine with the uniprocessor kernel, but when I boot from
bsd.mp, it sits at "mtrr: Pentium Pro MTRR support", then after a
minute or two it reports "ami0: timeout ccb 1" and hangs.

I found http://marc.theaimsgroup.com/?m=109355301607068, which
suggested upgrading the firmware on the card.  I upgraded to the
most current firmeware from AMI, no change.  It's an HP NetRAID 2M
and/or Megaraid Elite 1600.

Dmesg from /bsd:

OpenBSD 3.7 (GENERIC) #50: Sun Mar 20 00:01:57 MST 2005
    [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III Xeon ("GenuineIntel" 686-class, 2048KB L2
cache) 500 MHz
cpu0:

FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE3

6,MMX,FXSR,SSE
real mem  = 3220791296 (3145304K)
avail mem = 2931523584 (2862816K)
using 4278 buffers containing 161140736 bytes (157364K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 12/31/99, BIOS32 rev. 0 @
0xf0000
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x2000
pcibios0: PCI BIOS has 10 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:15:0 ("Intel 82371AB PIIX4
ISA" rev 0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1400 0xe8000/0x6000
0xee000/0x2000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
fxp0 at pci0 dev 1 function 0 "Intel 82557" rev 0x0d, i82550: irq
11, address 00:02:b3:8f:1a:3f
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4

"Compaq PCI Hotplug" rev 0x04 at pci0 dev 11 function 0 notconfigured

"Compaq Netelligent ASMC" rev 0x00 at pci0 dev 12 function 0 not
configured
siop0 at pci0 dev 13 function 0 "Symbios Logic 53c875" rev 0x14:
irq 10, using 4K of on-board RAM
scsibus0 at siop0: 16 targets
siop1 at pci0 dev 13 function 1 "Symbios Logic 53c875" rev 0x14:
irq 5, using 4K of on-board RAM
scsibus1 at siop1: 16 targets
vga1 at pci0 dev 14 function 0 "ATI Mach64 GV" rev 0x7a
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 15 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 15 function 1 "Intel 82371AB IDE" rev 0x01:
DMA, channel 0 wired to compatibility, channel 1 wired to
compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus2 at atapiscsi0: 2 targets
cd0 at scsibus2 targ 0 lun 0: <COMPAQ, CDR-8435, 0013> SCSI0 5/
cdrom removable
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
uhci0 at pci0 dev 15 function 2 "Intel 82371AB USB" rev
0x01pci_intr_map: no mapping for pin D
: couldn't map interrupt
"Intel 82371AB Power Mgmt" rev 0x02 at pci0 dev 15 function 3 not
configured
pchb0 at pci0 dev 16 function 0 "Intel 82451NX Mem & IO" rev 0x03
pchb1 at pci0 dev 18 function 0 "Intel 82454NX PXB" rev 0x04
pchb2 at pci0 dev 20 function 0 "Intel 82454NX PXB" rev 0x04
pci1 at pchb2 bus 4
ppb0 at pci1 dev 3 function 0 "DEC 21154 PCI-PCI" rev 0x05
pci2 at ppb0 bus 5
ppb1 at pci2 dev 0 function 0 "DEC 21154 PCI-PCI" rev 0x05
pci3 at ppb1 bus 6
ami0 at pci3 dev 0 function 0 "AMI MegaRAID" rev 0x02: irq 5 AMI
493/64b/lhc
ami0: FW 111U, BIOS vF320, 128MB RAM
ami0: 2 channels, 0 FC loops, 1 logical drives
scsibus3 at ami0: 40 targets
sd0 at scsibus3 targ 0 lun 0: <AMI, Host drive #00, > SCSI2 0/
direct fixed
sd0: 8677MB, 1106 cyl, 255 head, 63 sec, 512 bytes/sec, 17770496
sec total
"QLogic ISP12160" rev 0x06 at pci2 dev 1 function 0 not configured

"Compaq PCI Hotplug" rev 0x04 at pci1 dev 11 function 0 notconfigured


isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard,
using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask e765 netmask ef65 ttymask ffe7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: sd0 matched BIOS disk 80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02

Re: Hang using generic.mp with ami0

Reply via email to