Dale, me cope con IPv6, aunque tune q peliar al de sixxx para q me de un tunel, no se q mambo tiene con el mail q uso, no le gusta ninguna de mis direcciones ¬¬
q recomendas, 4to6 o un tunel? (cual?) tengo algo de latencia, no demasiada, pero 100ms mas que en ipv4 mas o menos. 2008/3/24 Horacio Castellini <[EMAIL PROTECTED]>: > > --- Luis <[EMAIL PROTECTED]> escribió: > > > 2002::/16 es un prefijo de ip4 sobre ipv6 tuneleado... > no mapeado o representado como ipv6 que en todo caso > serían de la forma ::ffff:wwww.xxxx.yyyy.zzzz Los > túneles en general operan sobre el puerto 40 sobre > otro par que en general es una empresa privada que te > da ipv6 2001::/16 o 3ffe::/16 .... > > Cuando de la charla sobre ipv6 explicaré mejor el > asunto... (si el gato me consigue un lugar y cañon > para proyectar ;) > > > > > Hola! tanto tiempo colgado...hace unos dias me > > sacaron el tema de IPv6 > > y ayer flasheando el AP con la ultra ultima version > > de dd-wrt encontre > > soporte a IPv6 y me dispuse a habilitarlo (como > > pude) leibastante pero > > hay muchisimas cosas que no entiendo, asique voy a > > pstear "lo que veo" > > en mi LAN/WAN y despues hacer las preguntas... > > > > AP: > > > > > > [EMAIL PROTECTED]:~# ip addr show > > 1: lo: <LOOPBACK,MULTICAST,UP> mtu 16436 qdisc > > noqueue > > link/loopback 00:00:00:00:00:00 brd > > 00:00:00:00:00:00 > > inet 127.0.0.1/8 brd 127.255.255.255 scope host > > lo > > inet6 ::1/128 scope host > > 2: teql0: <NOARP> mtu 1500 qdisc noop > > link/void > > 3: eth0: <BROADCAST,MULTICAST,PROMISC,UP> mtu 1500 > > qdisc pfifo_fast > > link/ether 00:1c:10:41:23:80 brd > > ff:ff:ff:ff:ff:ff > > inet6 fe80::21c:10ff:fe41:2380/64 scope link > > 4: eth1: <BROADCAST,MULTICAST,PROMISC,UP> mtu 1500 > > qdisc pfifo_fast > > link/ether 00:1c:10:41:23:82 brd > > ff:ff:ff:ff:ff:ff > > inet6 fe80::21c:10ff:fe41:2382/64 scope link > > 5: vlan0: <BROADCAST,MULTICAST,PROMISC,UP> mtu 1500 > > qdisc noqueue > > link/ether 00:1c:10:41:23:80 brd > > ff:ff:ff:ff:ff:ff > > inet6 fe80::21c:10ff:fe41:2380/64 scope link > > 6: vlan1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc > > noqueue > > link/ether 00:1c:10:41:23:81 brd > > ff:ff:ff:ff:ff:ff > > inet 201.212.206.84/24 brd 201.212.206.255 scope > > global vlan1 > > inet6 fe80::21c:10ff:fe41:2381/64 scope link > > 7: br0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc htb > > link/ether 00:1c:10:41:23:80 brd > > ff:ff:ff:ff:ff:ff > > inet 192.168.1.1/24 brd 192.168.1.255 scope > > global br0 > > inet 169.254.255.1/16 brd 169.254.255.255 scope > > global br0:0 > > inet6 2002:c9d4:ce54:1::1/64 scope global > > inet6 fe80::21c:10ff:fe41:2380/64 scope link > > 8: imq0: <NOARP,UP> mtu 1500 qdisc htb > > link/void > > 9: imq1: <NOARP> mtu 1500 qdisc noop > > link/void > > 10: [EMAIL PROTECTED]: <NOARP> mtu 1480 qdisc noop > > link/sit 0.0.0.0 brd 0.0.0.0 > > 11: [EMAIL PROTECTED]: <NOARP,UP> mtu 1280 qdisc noqueue > > link/sit 201.212.206.84 brd 0.0.0.0 > > inet6 2002:c9d4:ce54::1/16 scope global > > inet6 ::201.212.206.84/128 scope global > > > > > > Router (IPv4) > > > > [EMAIL PROTECTED]:~# ip -4 addr show > > 1: lo: <LOOPBACK,MULTICAST,UP> mtu 16436 qdisc > > noqueue > > inet 127.0.0.1/8 brd 127.255.255.255 scope host > > lo > > 6: vlan1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc > > noqueue > > inet 201.212.206.84/24 brd 201.212.206.255 scope > > global vlan1 > > 7: br0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc htb > > inet 192.168.1.1/24 brd 192.168.1.255 scope > > global br0 > > inet 169.254.255.1/16 brd 169.254.255.255 scope > > global br0:0 > > > > > > > > PC: (gentoo, con modulo ipv6 y ping6, nada mas tiene > > soporte IPv6, > > salvo el firefox, porque accedo a muchos lugares > > IPv6...(es un binario > > de ffox 3) > > > > Vger bin # ifconfig > > eth0 Link encap:Ethernet HWaddr > > 00:13:8F:BF:55:08 > > inet addr:192.168.1.100 > > Bcast:192.168.1.255 Mask:255.255.255.0 > > inet6 addr: > > 2002:c9d4:ce54:1:213:8fff:febf:5508/64 Scope:Global > > inet6 addr: fe80::213:8fff:febf:5508/64 > > Scope:Link > > UP BROADCAST RUNNING MULTICAST MTU:1500 > > Metric:1 > > RX packets:31860 errors:0 dropped:0 > > overruns:0 frame:0 > > TX packets:32484 errors:0 dropped:0 > > overruns:0 carrier:0 > > collisions:0 txqueuelen:1000 > > RX bytes:28029076 (26.7 Mb) TX > > bytes:5251301 (5.0 Mb) > > Interrupt:28 Base address:0x6000 > > > > > > > > Para el AP hice algunos pasos de aca: > > http://www.dd-wrt.com/wiki/index.php/IPv6#6to4_Setup > > basicamente solo agregue la config de radvd: > > > > interface br0 { > > MinRtrAdvInterval 3; > > MaxRtrAdvInterval 10; > > AdvLinkMTU 1280; > > AdvSendAdvert on; > > prefix 0:0:0:1::/64 { > > AdvOnLink on; > > AdvAutonomous on; > > AdvValidLifetime 86400; > > AdvPreferredLifetime 86400; > > Base6to4Interface vlan1; > > }; > > }; > > > > > > y luego un script al inicio en el AP: > > > > sleep 5 > > WANIP=$(ip -4 addr show dev vlan1 | grep 'inet ' | > > awk '{print $2}' | > > cut -d/ -f1) > > if [ -n "$WANIP" ] > > then > > V6PREFIX=$(printf '2002:%02x%02x:%02x%02x' $(echo > > $WANIP | tr . ' ')) > > ip tunnel add tun6to4 mode sit ttl 255 remote any > > local $WANIP > > ip link set tun6to4 mtu 1280 > > ip link set tun6to4 up > > ip addr add $V6PREFIX:0::1/16 dev tun6to4 > > ip addr add $V6PREFIX:1::1/64 dev br0 > > ip -6 route add 2000::/3 via ::192.88.99.1 dev > > tun6to4 > > kill -HUP $(cat /var/run/radvd.pid) > > fi > > > > > > Todo esto me da como resultado la configuracion de > > arriba, ahora, por > > lo que entiendo estoy usando alguna clase de tunel, > > por lo que mi > > trafico IPv6 es encapsulado en el AP adentro de > > IPv4, > > > > 1) Es asi? > > > > 2) Es posible NO usar un tunel y tener trafico IPv6 > > directamente a > > internet?? (tengo flash cablemodem......) > > > > 3) mi IP tiene prefijo 2002, indicando que estoy en > > un tunel 6 a 4, > > por ende la IP es dinamica....puedo conseguir alguna > > IP estatica? > > preferentemente con algun servicio que no necesite > > software extra > > > > > > Saludos y gracias, espero no estar haciendo > > preguntas tontas, pero lei > > bastante y hay muchas cosas que no me terminan de > > cerrar... :S > > > > > > > > -- > > Luis Diaz - Es solo cuestion de Fe y ser > > optimista.... > > > _______________________________________________ > > Lugro mailing list > > [email protected] > > http://www.lugro.org.ar/mailman/listinfo/lugro > > > > > __________________________________________________ > Correo Yahoo! > Espacio para todos tus mensajes, antivirus y antispam ¡gratis! > ¡Abrí tu cuenta ya! - http://correo.yahoo.com.ar > _______________________________________________ > Lugro mailing list > [email protected] > http://www.lugro.org.ar/mailman/listinfo/lugro > -- Luis Diaz - Es solo cuestion de Fe y ser optimista....
_______________________________________________ Lugro mailing list [email protected] http://www.lugro.org.ar/mailman/listinfo/lugro
