This patch enhances the "mvmdio" to support a SMI error/done interrupt
line which can be used along with a wait queue instead of doing
busy-waiting on the registers. This is a feature which is available in
the mv643xx_eth SMI code and thus reduces again the gap between the two.
Signed-off-by: Florian Fainelli <flor...@openwrt.org>
---
.../devicetree/bindings/net/marvell-orion-mdio.txt | 3 +
drivers/net/ethernet/marvell/mvmdio.c | 83 +++++++++++++++++---
2 files changed, 75 insertions(+), 11 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt
b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt
index 34e7aaf..052b5f2 100644
--- a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt
+++ b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt
@@ -9,6 +9,9 @@ Required properties:
- compatible: "marvell,orion-mdio"
- reg: address and length of the SMI register
+Optional properties:
+- interrupts: interrupt line number for the SMI error/done interrupt
+
The child nodes of the MDIO driver are the individual PHY devices
connected to this MDIO bus. They must have a "reg" property given the
PHY address on the MDIO bus.
diff --git a/drivers/net/ethernet/marvell/mvmdio.c
b/drivers/net/ethernet/marvell/mvmdio.c
index 5ecda58..cada794 100644
--- a/drivers/net/ethernet/marvell/mvmdio.c
+++ b/drivers/net/ethernet/marvell/mvmdio.c
@@ -24,10 +24,14 @@
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/phy.h>
+#include <linux/interrupt.h>
#include <linux/of_address.h>
#include <linux/of_mdio.h>
+#include <linux/of_irq.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
+#include <linux/sched.h>
+#include <linux/wait.h>
#define MVMDIO_SMI_DATA_SHIFT 0
#define MVMDIO_SMI_PHY_ADDR_SHIFT 16
@@ -36,12 +40,28 @@
#define MVMDIO_SMI_WRITE_OPERATION 0
#define MVMDIO_SMI_READ_VALID BIT(27)
#define MVMDIO_SMI_BUSY BIT(28)
+#define MVMDIO_ERR_INT_CAUSE 0x007C
+#define MVMDIO_ERR_INT_SMI_DONE 0x00000010
+#define MVMDIO_ERR_INT_MASK 0x0080
struct orion_mdio_dev {
struct mutex lock;
void __iomem *regs;
+ /*
+ * If we have access to the error interrupt pin (which is
+ * somewhat misnamed as it not only reflects internal errors
+ * but also reflects SMI completion), use that to wait for
+ * SMI access completion instead of polling the SMI busy bit.
+ */
+ int err_interrupt;
+ wait_queue_head_t smi_busy_wait;
};
+static int orion_mdio_smi_is_done(struct orion_mdio_dev *dev)
+{
+ return !(readl(dev->regs) & MVMDIO_SMI_BUSY);
+}
+
/* Wait for the SMI unit to be ready for another operation
*/
static int orion_mdio_wait_ready(struct mii_bus *bus)
@@ -50,19 +70,30 @@ static int orion_mdio_wait_ready(struct mii_bus *bus)
int count;
u32 val;
- count = 0;
- while (1) {
- val = readl(dev->regs);
- if (!(val & MVMDIO_SMI_BUSY))
- break;
-
- if (count > 100) {
- dev_err(bus->parent, "Timeout: SMI busy for too
long\n");
- return -ETIMEDOUT;
+ if (dev->err_interrupt == NO_IRQ) {
+ count = 0;
+ while (1) {
+ val = readl(dev->regs);
+ if (!(val & MVMDIO_SMI_BUSY))
+ break;
+
+ if (count > 100) {
+ dev_err(bus->parent,
+ "Timeout: SMI busy for too long\n");
+ return -ETIMEDOUT;
+ }
+
+ udelay(10);
+ count++;
}
+ }
- udelay(10);
- count++;
+ if (!orion_mdio_smi_is_done(dev)) {
+ wait_event_timeout(dev->smi_busy_wait,
+ orion_mdio_smi_is_done(dev),
+ msecs_to_jiffies(100));
+ if (!orion_mdio_smi_is_done(dev))
+ return -ETIMEDOUT;
}
return 0;
@@ -141,6 +172,21 @@ static int orion_mdio_reset(struct mii_bus *bus)
return 0;
}
+static irqreturn_t orion_mdio_err_irq(int irq, void *dev_id)
+{
+ struct orion_mdio_dev *dev = dev_id;
+
+ if (readl(dev->regs + MVMDIO_ERR_INT_CAUSE) &
+ MVMDIO_ERR_INT_SMI_DONE) {
+ writel(~MVMDIO_ERR_INT_SMI_DONE,
+ dev->regs + MVMDIO_ERR_INT_CAUSE);
+ wake_up(&dev->smi_busy_wait);
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
static int orion_mdio_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
@@ -181,6 +227,19 @@ static int orion_mdio_probe(struct platform_device *pdev)
return -ENODEV;
}
+ dev->err_interrupt = NO_IRQ;
+ init_waitqueue_head(&dev->smi_busy_wait);
+
+ dev->err_interrupt = irq_of_parse_and_map(pdev->dev.of_node, 0);
+ if (dev->err_interrupt != NO_IRQ) {
+ ret = devm_request_irq(&pdev->dev, dev->err_interrupt,
+ orion_mdio_err_irq,
+ IRQF_SHARED, pdev->name, dev);
+ if (!ret)
+ writel(MVMDIO_ERR_INT_SMI_DONE,
+ dev->regs + MVMDIO_ERR_INT_MASK);
+ }
+
mutex_init(&dev->lock);
ret = of_mdiobus_register(bus, np);
@@ -202,6 +261,8 @@ static int orion_mdio_remove(struct platform_device *pdev)
struct mii_bus *bus = platform_get_drvdata(pdev);
struct orion_mdio_dev *dev = bus->priv;
+ writel(0, dev->regs + MVMDIO_ERR_INT_MASK);
+ free_irq(dev->err_interrupt, dev);
mdiobus_unregister(bus);
kfree(bus->irq);
mdiobus_free(bus);
--
1.7.10.4
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
