A gentle reminder.
Any comments are appreciated.
Regards,
Sandeep
> -----Original Message-----
> From: Singh Sandeep-B37400
> Sent: Wednesday, January 02, 2013 6:55 PM
> To: devicetree-disc...@lists.ozlabs.org; linuxppc-...@ozlabs.org
> Cc: Singh Sandeep-B37400; Aggrwal Poonam-B10812
> Subject: [PATCH] Added device tree binding for TDM and TDM phy
>
> This controller is available on many Freescale SOCs like MPC8315, P1020,
> P1010 and P1022
>
> Signed-off-by: Sandeep Singh <sand...@freescale.com>
> Signed-off-by: Poonam Aggrwal <poonam.aggr...@freescale.com>
> ---
> .../devicetree/bindings/powerpc/fsl/fsl-tdm.txt | 63
> ++++++++++++++++++++
> .../devicetree/bindings/powerpc/fsl/tdm-phy.txt | 38 ++++++++++++
> 2 files changed, 101 insertions(+), 0 deletions(-) create mode 100644
> Documentation/devicetree/bindings/powerpc/fsl/fsl-tdm.txt
> create mode 100644 Documentation/devicetree/bindings/powerpc/fsl/tdm-
> phy.txt
>
> diff --git a/Documentation/devicetree/bindings/powerpc/fsl/fsl-tdm.txt
> b/Documentation/devicetree/bindings/powerpc/fsl/fsl-tdm.txt
> new file mode 100644
> index 0000000..ceb2ef1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/powerpc/fsl/fsl-tdm.txt
> @@ -0,0 +1,63 @@
> +TDM Device Tree Binding
> +
> +NOTE: The bindings described in this document are preliminary and
> +subject to change.
> +
> +TDM (Time Division Multiplexing)
> +
> +Description:
> +
> +The TDM is full duplex serial port designed to allow various devices
> +including digital signal processors (DSPs) to communicate with a
> +variety of serial devices including industry standard framers, codecs,
> other DSPs and microprocessors.
> +
> +The below properties describe the device tree bindings for Freescale
> +TDM controller. This TDM controller is available on various Freescale
> +Processors like MPC8315, P1020, P1022 and P1010.
> +
> +Required properties:
> +
> +- compatible
> + Value type: <string>
> + Definition: Should contain "fsl,tdm1.0".
> +
> +- reg
> + Definition: A standard property. The first reg specifier describes
> the TDM
> + registers, and the second describes the TDM DMAC registers.
> +
> +- tdm_tx_clk
> + Value type: <u32 or u64>
> + Definition: This specifies the value of transmit clock. It should
> not
> + exceed 50Mhz.
> +
> +- tdm_rx_clk
> + Value type: <u32 or u64>
> + Definition: This specifies the value of receive clock. Its value
> could be
> + zero, in which case tdm will operate in shared mode. Its value
> should not
> + exceed 50Mhz.
> +
> +- interrupts
> + Definition: Two interrupt specifiers. The first is TDM error, and
> the
> + second is TDM DMAC.
> +
> +- phy-handle
> + Value type: <phandle>
> + Definition: Phandle of the line controller node or framer node eg.
> SLIC,
> + E1/T1 etc. (Refer
> +Documentation/devicetree/bindings/powerpc/fsl/tdm-phy.txt)
> +
> +- fsl,max-time-slots
> + Value type: <u32>
> + Definition: Maximum number of 8-bit time slots in one TDM frame.
> This is
> + the maximum number which TDM hardware supports.
> +
> +Example:
> +
> + tdm@16000 {
> + compatible = "fsl,tdm1.0";
> + reg = <0x16000 0x200 0x2c000 0x2000>;
> + tdm_tx_clk = <2048000>;
> + tdm_rx_clk = <0>;
> + interrupts = <16 8 62 8>;
> + phy-handle = <&tdm-phy>;
> + fsl,max-time-slots = <128>;
> + };
> diff --git a/Documentation/devicetree/bindings/powerpc/fsl/tdm-phy.txt
> b/Documentation/devicetree/bindings/powerpc/fsl/tdm-phy.txt
> new file mode 100644
> index 0000000..2563934
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/powerpc/fsl/tdm-phy.txt
> @@ -0,0 +1,38 @@
> +TDM PHY Device Tree Binding
> +
> +NOTE: The bindings described in this document are preliminary and
> +subject to change.
> +
> +Description:
> +TDM PHY is the terminal interface of TDM subsystem. It is typically a
> +line control device like E1/T1 framer or SLIC. A TDM device can have
> +multiple TDM PHYs.
> +
> +Required properties:
> +
> +- compatible
> + Value type: <string>
> + Definition: Should contain generic compatibility like "tdm-phy-slic"
> or
> + "tdm-phy-e1" or "tdm-phy-t1".
> +
> +- max-num-ports
> + Value type: <u32>
> + Definition: Defines the maximum number of ports supported by the
> SLIC
> + device. Only required if the device is SLIC. For E1/T1 devices the
> number
> + of ports are predefined i.e. (24 in case of T1 and 32 in case of
> E1).
> +
> +Apart from the above, there may be other properties required because of
> +the bus/interface this device is connected on. It could be SPI/local
> bus, etc.
> +
> +Example:
> +
> + tdm-phy@0 {
> + compatible = "zarlink,le88266","tdm-phy-slic";
> + reg = <0>;
> + max-num-ports = <4>;
> + spi-max-frequency = <8000000>;
> + };
> +
> +In the above example properties "reg" and "spi-max-frequency" are SPI
> +specific as the SLIC device is connected on SPI interface. These
> +properties might vary depending on the specific interface the device is
> using.
> --
> 1.7.6.GIT
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
