Hi all
I got completely stuck with a network adapter problem on my
ppc board (MPC52xx style). The ntwork adapter does not seem
to intialize correctly when booted without 'help from uboot'
The adapter works properly when I first use it with uboot. E.g.
using tftp to load the kernel or just issuing a dummy sntp
command. It does not get intialized if I boot linux without
using any network relevant command in ubboot
The difference manifests on the boot message: (working)
PHY working
...
mpc52xx MII bus: probed
TCP cubic registered
NET: Registered protocol family 17
IP-Config: Complete:
device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2,
host=192.168.1.245, domain=, nis-domain=(none),
bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.244
Looking up port of RPC 100005/1 on 192.168.1.244
VFS: Mounted root (nfs filesystem) on device 0:11.
Freeing unused kernel memory: 124k init
PHY: f0003000:00 - Link is Up - 100/Full
# ping 192.168.1.2 returns proper results.
PHY Not working:
...
mpc52xx MII bus: probed
TCP cubic registered
NET: Registered protocol family 17
IP-Config: Complete:
device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2,
host=192.168.1.245, domain=, nis-domain=(none),
bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 124k init
# ping 192.168.1.2 hangs
The second snipped does not have "Looking up.." messages because it
boots from flash. Main difference is "PHY: f0003000:00 - Link is Up - 100/Full"
which does not appear at the failing case.
Linux Version is 2.6.35.7 patched with xenomai 2.5
U-Boot 2010.06 (Aug 05 2010 - 19:54:45)
Linux configuration see below: ( i left most entries out that are not set)
I also experimented with different settings but finally only
CONFIG_FEC_MPC52xx=y and CONFIG_FEC_MPC52xx_MDIO=y
seem to be of any relevance. If both are set, the adapter works
when initialized by uboot.
Any help or tips will be very much appreciated,
Regards, Peter
Linux .config
...
#
# Platform support
#
# CONFIG_PPC_CHRP is not set
# CONFIG_MPC5121_ADS is not set
# CONFIG_MPC5121_GENERIC is not set
CONFIG_PPC_MPC52xx=y
CONFIG_PPC_MPC5200_SIMPLE=y
# CONFIG_PPC_EFIKA is not set
CONFIG_PPC_LITE5200=y
# CONFIG_PPC_MEDIA5200 is not set
CONFIG_PPC_MPC5200_BUGFIX=y
# CONFIG_PPC_MPC5200_GPIO is not set
CONFIG_PPC_MPC5200_LPBFIFO=y
CONFIG_PPC_BESTCOMM=y
CONFIG_PPC_BESTCOMM_FEC=y
CONFIG_PPC_BESTCOMM_GEN_BD=y
# CONFIG_SIMPLE_GPIO is not set
..
# Bus options
#
CONFIG_ZONE_DMA=y
CONFIG_NEED_SG_DMA_LENGTH=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_PPC_PCI_CHOICE=y
...
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
#
# MII PHY device drivers
#
CONFIG_LXT_PHY=y ## Does not seem to have any influence
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
CONFIG_ETHOC=y ## Does not seem to have any influence
CONFIG_FEC_MPC52xx=y ## Must be Y in roder to get adapter working
with uboot's init
CONFIG_FEC_MPC52xx_MDIO=y ## Must be Y in roder to get adapter working with
uboot's init
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
