On 06/24/2010 06:54 AM, Gary Thomas wrote:
I thought I had this working, but it seems to only work for UCC3.
Sadly, I can't get it to work on UCC4/UCC5/UCC8 at all.
Starting with UCC4, I have:
/* ttyQE0 (UCC4) */
serial_qe0: ser...@3200 {
device_type = "serial";
compatible = "ucc_uart";
cell-index = <4>;
reg = <0x3200 0x200>;
interrupts = <35>;
interrupt-parent = <&qeic>;
port-number = <0>;
rx-clock-name = "brg9";
tx-clock-name = "brg10";
soft-uart;
};
With this setup, I can receive characters from the device, but
no characters ever go out. Same behaviour as before - the output
descriptors get filled, but no action seems to be taken, no interrupts,
etc. Except randomly there will be output! For example, if I
connect to the port with minicom, what I type is received by /dev/ttyQE2.
On some rare occasions, what I type is also echoed back, but when
this happens, it's only the first couple of characters, then nothing.
I verified that the CMXUCR registers are being set per the DTS
as well as the BRG registers. They all look correct:
ucc_set_qe_mux_rxtx - CMX: 0x000a0000
r...@ppc_target:~ stty </dev/ttyQE0 38400
qe_setbrg - BRG: fddfd660 = 0x000106b6, CLK = 132000000, RATE = 9600,
MULTIPLIER = 16
qe_setbrg - BRG: fddfd664 = 0x000106b5, CLK = 132000000, RATE = 9600,
MULTIPLIER = 1
qe_setbrg - BRG: fddfd660 = 0x000101aa, CLK = 132000000, RATE = 38400,
MULTIPLIER = 16
qe_setbrg - BRG: fddfd664 = 0x00011ada, CLK = 132000000, RATE = 38400,
MULTIPLIER = 1
I've also tried this on UCC5 & UCC8 which show the identical
behaviour - input works, output does not. I've tried running
with only a single soft UART (UCC4) as well as having all three
configured. No changes seen.
At this point, I'm using the stock driver from 2.6.33.3
One thing I noticed is that the firmware patch seems quite old.
I got the firmware package from http://opensource.freescale.com/firmware/
We were also told (by FreeScale) to look at
https://www.freescale.com/webapp/Download?colCode=QERAMPKG
Looking at these two packages, it's unclear that they match. Certainly
the dates are very different:
[gtho...@hermes 8358]$ ls -l fsl_qe_ucode QERAMPKG
fsl_qe_ucode:
total 16
-rw-rw-r-- 1 gthomas gthomas 5940 2007-12-10 14:39
fsl_qe_ucode_uart_8360_21.bin
-rw-r--r-- 1 gthomas gthomas 7892 2007-11-30 10:14 license.txt
QERAMPKG:
total 972
-rw-rw-r-- 1 gthomas gthomas 132915 2009-04-07 14:04
SlowProtocols_8323rev11.c
-rw-rw-r-- 1 gthomas gthomas 455446 2009-09-16 15:44
Soft_UART_Microcode_Rel_0_1_2.pdf
-rw-rw-r-- 1 gthomas gthomas 29379 2009-09-16 15:49
Soft_UART_mpc8360_r2.0.h
-rw-rw-r-- 1 gthomas gthomas 29379 2009-09-16 15:14
Soft_UART_mpc8360_r2.1.h
-rw-rw-r-- 1 gthomas gthomas 29379 2009-09-16 15:14
Soft_UART_mpc8568_r1.1.h
-rw-rw-r-- 1 gthomas gthomas 105457 2009-09-16 16:00 SWUART_8360rev20.c
-rw-rw-r-- 1 gthomas gthomas 34689 2009-09-16 15:32 SWUART_8360rev20.srx
-rw-rw-r-- 1 gthomas gthomas 105318 2009-09-16 15:59 SWUART_8360rev21.c
-rw-rw-r-- 1 gthomas gthomas 34689 2009-09-16 15:14 SWUART_8360rev21.srx
Any ideas what I'm doing wrong?
BTW, I tried converting the Soft_UART_mpc8360_r2.1.h file
to the firmware format. I had to fiddle with the conversion
program a bit because the firmware has version 0.1.2, but I
ended up with a new firmware file. Here's the change I made:
$ diff -u make_qe_firmware.py*
--- make_qe_firmware.py 2010-06-24 07:19:31.000000000 -0600
+++ make_qe_firmware.py~ 2010-06-24 07:15:54.000000000 -0600
@@ -260,7 +260,7 @@
print "Unknown SOC model\n"
exit(1)
-if not ucode_major and not ucode_minor:
+if not ucode_major:
print "Unknown microcode version\n"
exit(1)
No change in behaviour :-(
--
------------------------------------------------------------
Gary Thomas | Consulting for the
MLB Associates | Embedded world
------------------------------------------------------------
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
