Hi,
I'm currently working on a custom embedded card with ppc405ex installed.
On this card, EMAC1 is "phy-less", and connected directly to a MAC on a micrel
switch (ks8995ma).
I've tried the default phy-less mode currently supported by the core driver for
ibm_newmac, but found
this insufficient. I've made a patch for the core driver so it supports some
more scenarios.
Since the simultanious operation of both EMACS on PPC405EX requires utilization
of the RGMII bridge, I did not
manage setting the speed to less than 1Gbps using the current phy-less mode.
I've moved the phy-less setup to
the dts. I've also added a clock-internal which was required for my case, as
the SDR0_MFR E1CS register was set
by default in phy-less mode.
--- drivers/net/ibm_newemac/core.c 2010-02-19 11:13:00.000000000 +0100
+++ drivers/net/ibm_newemac/core.c 2010-02-19 12:53:56.000000000 +0100
@@ -2393,14 +2393,54 @@
/* PHY-less configuration.
* XXX I probably should move these settings to the dev tree
*/
+
+ if (emac_read_uint_prop(np, "phy-duplex", &dev->phy.duplex, 0))
+ dev->phy.duplex = 1;
+
+ if (emac_read_uint_prop(np, "phy-speed", &dev->phy.speed, 0))
+ dev->phy.speed = 100;
+
+ if (emac_read_uint_prop(np, "phy-autoneg", &dev->phy.autoneg, 0))
+ dev->phy.autoneg = 0;
+
dev->phy.address = -1;
dev->phy.features = SUPPORTED_MII;
- if (emac_phy_supports_gige(dev->phy_mode))
- dev->phy.features |= SUPPORTED_1000baseT_Full;
- else
- dev->phy.features |= SUPPORTED_100baseT_Full;
+
+ if (dev->phy.autoneg == 1 )
+ dev->phy.features |= SUPPORTED_Autoneg;
+
+ switch (dev->phy.duplex)
+ {
+ case 0:
+
+ if (dev->phy.speed == 10 )
+ dev->phy.features |= SUPPORTED_10baseT_Half;
+
+ if (dev->phy.speed == 100 )
+ dev->phy.features |= SUPPORTED_100baseT_Half;
+
+ if (dev->phy.speed == 100 )
+ dev->phy.features |= SUPPORTED_100baseT_Half;
+
+ default:
+
+ if (dev->phy.speed == 10 )
+ dev->phy.features |= SUPPORTED_10baseT_Full;
+
+ if (dev->phy.speed == 100 )
+ dev->phy.features |= SUPPORTED_100baseT_Full;
+
+ if (dev->phy.speed == 100 )
+ dev->phy.features |= SUPPORTED_100baseT_Full;
+ }
+
dev->phy.pause = 1;
+ #if defined (CONFIG_PPC_DCR_NATIVE) && defined (CONFIG_405EX)
+ if (of_get_property(np, "phy-clock-internal", NULL))
+ dcri_clrset(SDR0, SDR0_MFR, ( dev->rgmii_port ? SDR0_MFR_ECS >> 1
: SDR0_MFR_ECS ),0 );
+ #endif
+
return 0;
}
DTS example:
EMAC1: ether...@ef600a00 {
linux,network-index = <0x1>;
device_type = "network";
compatible = "ibm,emac-405ex", "ibm,emac4sync";
interrupt-parent = <&EMAC1>;
interrupts = <0x0 0x1>;
#interrupt-cells = <1>;
#address-cells = <0>;
#size-cells = <0>;
interrupt-map = </*Status*/ 0x0 &UIC0 0x19 0x4
/*Wake*/ 0x1 &UIC1 0x1f 0x4>;
reg = <0xef600a00 0x000000c4>;
local-mac-address = [0000000000];
mal-device = <&MAL0>;
mal-tx-channel = <1>;
mal-rx-channel = <1>;
cell-index = <1>;
max-frame-size = <9000>;
rx-fifo-size = <4096>;
tx-fifo-size = <2048>;
phy-mode = "rgmii";
phy-map = <0xffffffff>; // Be sure that the emac use phy-less
configuration
phy-address = <0xffffffff>; // Be sure that the emac use phy-less
configuration
phy-speed = <100>;
phy-duplex = <1>;
phy-autoneg = <0>;
phy-clock-internal;
rgmii-device = <&RGMII0>;
rgmii-channel = <1>;
has-inverted-stacr-oc;
has-new-stacr-staopc;
};
Best regards
Staale Aakermann, Systems Engineer
Kongsberg Defence Systems / Defence Communication
Olav Brunborgsv 6, P.O.Box 87, 1375 Billingstad, Norway
Phone: +47 66 84 24 00, Direct Phone: +47 66 74 48 51,
Fax: +47 66 84 82 30, Mobile: +47 928 29 879
Mail: staale.aakerm...@kongsberg.com<mailto:staale.aakerm...@kongsberg.com>
Url: www.kongsberg.com<http://www.kongsberg.com/>
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
