-----Original Message-----
From: gshan [mailto:gs...@alcatel-lucent.com]
Sent: Thursday, December 24, 2009 5:16 PM
To: mich...@ellerman.id.au
Cc: Kumar Gopalpet-B05799; net...@vger.kernel.org;
linuxppc-dev@lists.ozlabs.org
Subject: Re: [HELP] BAD interrupts
Michael Ellerman wrote:
On Wed, 2009-12-23 at 19:41 +0530, Kumar Gopalpet-B05799 wrote:
Hi all,
I am trying linux 2.6.32-rc3 in SMP mode. I am seeing a lot of BAD
interrupts when I do a "cat /proc/interrupts".
I am running a forwarding application b/w two ethernet ports
(ethernet uses gianfar driver).
Has any one observed these BAD interrupts ? If so, can someone help
me in understanding why these interrupts come and how to
resolve it ?
You'll need to tell us what platform you're running on.
The BAD interrupts come from ppc_spurious_interrupts. It's a
count of
the number of times we entered do_IRQ() (ie. took an external
interrupt), but when we asked the interrupt controller which irq it
was, the interrupt controller said there was no irq.
Depending on your interrupt controller that might happen
sometimes for
valid reasons. Or it might indicate something is setup wrong.
cheers
I think it will help to show us your /proc/interrupts so that
how you suffered from bad interrupts.
I am running linux-2.6.29 in SMP mode on P2020RDB ( ruuning at
1200/600/667). The test scenario forwarding
application and is a bidirectioanl flow between eth0 & eth2.
Attached is the complete log of the test scenario.
I also noted another observation that when all the interrupts are mapped
to a single core, the BAD interrupts stop coming.
--
Thanks
Sandeep
------------------------------------------------------------------------
tftp 1000000 etsec2/uImage_alpha
Speed: 1000, full duplex
Using eTSEC1 device
TFTP from server 10.232.134.194; our IP address is 10.232.133.188
Filename 'etsec2/uImage_alpha'.
Load address: 0x1000000
Loading: *#################################################################
#################################################################
###################################################
done
Bytes transferred = 2654090 (287f8a hex)
=> tftp 2000000 etsec2/rf ootfs_alpha
Speed: 1000, full duplex
Using eTSEC1 device
TFTP from server 10.232.134.194; our IP address is 10.232.133.188
Filename 'etsec2/rootfs_alpha'.
Load address: 0x2000000
Loading: *#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####
done
Bytes transferred = 26776875 (198952b hex)
=> tftp c00000 etsec2/p2020alpha.dtb
Speed: 1000, full duplex
Using eTSEC1 device
TFTP from server 10.232.134.194; our IP address is 10.232.133.188
Filename 'etsec2/p2020alpha.dtb'.
Load address: 0xc00000
Loading: *#
done
Bytes transferred = 10579 (2953 hex)
=> bootm 1000000 2000000 c00000
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-2.6.29
Created: 2009-07-03 9:42:06 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2654026 Bytes = 2.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: uboot ext2 ramdisk rootfs
Created: 2009-07-04 8:24:27 UTC
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 26776811 Bytes = 25.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00c00000
Booting using the fdt blob at 0xc00000
Uncompressing Kernel Image ... OK
Loading Ramdisk to 2e676000, end 2ffff4eb ... OK
Using P2020 RDB machine description
Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=256Mb residual: 256Mb
Linux version 2.6.29 (di...@uteam3.ap.freescale.net) (gcc version 4.3.2 (GCC) )
#1 SMP Fri Jul 3 15:11:50 IST 2009
Found initrd at 0xee676000:0xeffff4eb
CPU maps initialized for 1 thread per core
console [udbg0] enabled
setup_arch: bootmem
mpc85xx_rdb_setup_arch()
Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->255
PCI host bridge /p...@ffe09000 ranges:
MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
IO 0x00000000ffc30000..0x00000000ffc3ffff -> 0x0000000000000000
Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->255
PCI host bridge /p...@ffe0a000 ranges:
MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
MPC85xx RDB board from Freescale Semiconductor
arch: exit
Zone PFN ranges:
DMA 0x00000000 -> 0x00030000
Normal 0x00030000 -> 0x00030000
HighMem 0x00030000 -> 0x00040000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00040000
MMU: Allocated 1088 bytes of context maps for 255 contexts
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
Kernel command line: root=/dev/ram rw console=ttyS0,115200 ramdisk_size=275000
cache-sram-size=0x10000
mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
mpic: ISU size: 256, shift: 8, mask: ff
mpic: Initializing for 256 sources
PID hash table entries: 4096 (order: 12, 16384 bytes)
clocksource: timebase mult[3555555] shift[22] registered
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1007184k/1048576k available (5180k kernel code, 40848k reserved, 164k
data, 134k bss, 216k init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Calibrating delay loop... 149.50 BogoMIPS (lpj=299008)
Mount-cache hash table entries: 512
mpic: requesting IPIs ...
Processor 1 found.
Brought up 2 CPUs
net_namespace: 732 bytes
NET: Registered protocol family 16
PCI: Probing PCI hardware
pci 0000:00:00.0: ignoring class b20 (doesn't match header type 01)
pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0001:02:00.0: ignoring class b20 (doesn't match header type 01)
pci 0001:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0001:02:00.0: PME# disabled
pci 0000:00:00.0: not setting up bridge for bus 0000:01
pci 0000:00:00.0: enabling device (0106 -> 0107)
pci 0001:02:00.0: not setting up bridge for bus 0001:03
pci 0001:02:00.0: enabling device (0106 -> 0107)
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Freescale Elo / Elo Plus DMA driver
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 26149k freed
fsl-elo-dma ffe0c300.dma: Probe the Freescale DMA driver for fsl,eloplus-dma
controller at ffe0c300...
fsl-elo-dma ffe0c300.dma: #0 (fsl,eloplus-dma-channel), irq 76
fsl-elo-dma ffe0c300.dma: #1 (fsl,eloplus-dma-channel), irq 77
fsl-elo-dma ffe0c300.dma: #2 (fsl,eloplus-dma-channel), irq 78
fsl-elo-dma ffe0c300.dma: #3 (fsl,eloplus-dma-channel), irq 79
fsl-elo-dma ffe21300.dma: Probe the Freescale DMA driver for fsl,eloplus-dma
controller at ffe21300...
fsl-elo-dma ffe21300.dma: #0 (fsl,eloplus-dma-channel), irq 20
fsl-elo-dma ffe21300.dma: #1 (fsl,eloplus-dma-channel), irq 21
fsl-elo-dma ffe21300.dma: #2 (fsl,eloplus-dma-channel), irq 22
fsl-elo-dma ffe21300.dma: #3 (fsl,eloplus-dma-channel), irq 23
audit: initializing netlink socket (disabled)
type=2000 audit(2.388:1): initialized
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
NTFS driver 2.1.29 [Flags: R/O].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
JFFS2: default compression mode: priority
msgmni has been set to 1507
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Generic non-volatile memory driver v1.1
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A
console handover: boot [udbg0] -> real [ttyS0]
serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A
brd: module loaded
loop: module loaded
nbd: registered device at major 43
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6
e1000e: Copyright (c) 1999-2008 Intel Corporation.
Gianfar MII Bus: probed
Gianfar MII Bus: probed
eth0 (fsl-gianfar): not using net_device_ops yet
eth0: Gianfar Ethernet Controller Version 1.4-skbr1.1.4, 00:04:9f:0c:05:00
eth0: MTU = 1500 (frame size=1524, truesize=1800)
eth0: Running with NAPI enabled
eth0: 128/128 RX/TX BD ring size
eth1 (fsl-gianfar): not using net_device_ops yet
eth1: Gianfar Ethernet Controller Version 1.4-skbr1.1.4, 00:04:9f:0c:05:01
eth1: MTU = 1500 (frame size=1524, truesize=1800)
eth1: Running with NAPI enabled
eth1: 128/128 RX/TX BD ring size
eth2 (fsl-gianfar): not using net_device_ops yet
eth2: Gianfar Ethernet Controller Version 1.4-skbr1.1.4, 00:04:9f:0c:05:02
eth2: MTU = 1500 (frame size=1524, truesize=1800)
eth2: Running with NAPI enabled
eth2: 128/128 RX/TX BD ring size
Fixed MDIO Bus: probed
st: Version 20081215, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
ef000000.nor: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Creating 5 MTD partitions on "ef000000.nor":
0x000000000000-0x000000040000 : "NOR (RO) Vitesse-7385 Firmware"
ftl_cs: FTL header not found.
0x000000040000-0x000000080000 : "NOR (RO) DTB Image"
ftl_cs: FTL header not found.
0x000000080000-0x000000400000 : "NOR (RO) Linux Kernel Image"
ftl_cs: FTL header not found.
0x000000400000-0x000000f00000 : "NOR (RW) JFFS2 Root File System"
ftl_cs: FTL header not found.
0x000000f00000-0x000001000000 : "NOR (RO) U-Boot Image"
ftl_cs: FTL header not found.
NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V
8-bit)
RedBoot partition parsing not available
Creating 6 MTD partitions on "ffa00000.flash":
0x000000000000-0x000000080000 : "NAND (RO) U-Boot Image"
ftl_cs: FTL header not found.
0x000000080000-0x000000100000 : "NAND (RO) DTB Image"
ftl_cs: FTL header not found.
0x000000100000-0x000000500000 : "NAND (RO) Linux Kernel Image"
ftl_cs: FTL header not found.
0x000000500000-0x000000900000 : "NAND (RO) Compressed RFS Image"
ftl_cs: FTL header not found.
0x000000900000-0x000001000000 : "NAND (RW) JFFS2 Root File System"
ftl_cs: FTL header not found.
0x000001000000-0x000002000000 : "NAND (RW) Writable User area"
ftl_cs: FTL header not found.
eLBC NAND device at 0xffa00000, bank 1
fsl_m25p80 spi28672.0: s25sl128b (0 Kbytes)
Creating 5 MTD partitions on "SPIFLASH0":
0x000000000000-0x000000080000 : "SPI (RO) U-Boot Image"
ftl_cs: FTL header not found.
0x000000080000-0x000000100000 : "SPI (RO) DTB Image"
ftl_cs: FTL header not found.
0x000000100000-0x000000500000 : "SPI (RO) Linux Kernel Image"
ftl_cs: FTL header not found.
0x000000500000-0x000000900000 : "SPI (RO) Compressed RFS Image"
ftl_cs: FTL header not found.
0x000000900000-0x000001000000 : "SPI (RW) JFFS2 RFS"
ftl_cs: FTL header not found.
ffe07000.spi: Freescale eSPI Controller driver at 0xf210a000 (irq = 59)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
esdhc: Freescale Enhanced Secure Digital Host Controller driver
mmc0: ESDHC at 0xffe2e000 irq 72 PIO
talitos ffe30000.crypto: hwrng
alg: No test for authenc(hmac(sha1),cbc(aes))
(authenc-hmac-sha1-cbc-aes-talitos)
talitos ffe30000.crypto: authenc-hmac-sha1-cbc-aes-talitos
alg: No test for authenc(hmac(sha1),cbc(des3_ede))
(authenc-hmac-sha1-cbc-3des-talitos)
talitos ffe30000.crypto: authenc-hmac-sha1-cbc-3des-talitos
alg: No test for authenc(hmac(sha256),cbc(aes))
(authenc-hmac-sha256-cbc-aes-talitos)
talitos ffe30000.crypto: authenc-hmac-sha256-cbc-aes-talitos
alg: No test for authenc(hmac(sha256),cbc(des3_ede))
(authenc-hmac-sha256-cbc-3des-talitos)
talitos ffe30000.crypto: authenc-hmac-sha256-cbc-3des-talitos
alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-talitos)
talitos ffe30000.crypto: authenc-hmac-md5-cbc-aes-talitos
alg: No test for authenc(hmac(md5),cbc(des3_ede))
(authenc-hmac-md5-cbc-3des-talitos)
talitos ffe30000.crypto: authenc-hmac-md5-cbc-3des-talitos
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <gree...@candelatech.com>
All bugs added by David S. Miller <da...@redhat.com>
rtc-ds1307 0-0068: setting system clock to 2009-07-01 10:24:20 UTC (1246443860)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem) on device 1:0.
Freeing unused kernel memory: 216k init
Mounting /proc and /sys
Setting the hostname to P2020RDB
Mounting filesystems
mount: sysfs already mounted or /sys busy
mount: according to mtab, /sys is already mounted on /sys
Starting syslogd and klogd
Running sysctl
Setting up networking on loopback device:
Setting up networking on eth0: ADDRCONF(NETDEV_UP): eth0: link is not ready
Adding static route for default gateway to 192.168.0.1:
Setting nameserver to 192.168.0.1 in /etc/resolv.conf:
SettingADDRCONF(NETDEV_UP): eth1: link is not ready
up networking on eth1:
Adding static route for default gateway to 192.168.1.1:
Setting nameserver to 192.168.1.1 in /etc/resolv.conf:
SettingADDRCONF(NETDEV_UP): eth2: link is not ready
up networking on eth2:
Adding static route for default gateway to 192.168.2.1:
Starting inetd:
Starting the port mapper:
Generating keys for the dropbear ssh server:
Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_key'
Generating key, this may take a while...
Public key portion is:
ssh-rsa
AAAAB3NzaC1yc2EAAAADAQABAAAAgwC8sk4V/7x6e0hJOjBdcGmUx26QQfpVdxT1z9itBPZf/bdfogKI5OHEfCPU2Tc+ZYNtrPXIgYvrML5I5z/WQL7QNgOx0/Vv
woNbxHLXj5UmirIJ6kNKlyUisPyZNU54XQjKCTpK7GjcGvUFgQMqv2HqWMfFV9XmytvXJgkhyg0jxox7
r...@p2020rdb
Fingerprint: md5 2d:50:46:59:d1:92:72:1f:07:cf:e4:b6:14:6c:86:f3
Starting the dropbear ssh server:
Starting the boa webserver:
Please set the system time using
date <mmddhhmnyyyy>
/sbin/hwclock -w
PHY: 0:01 - Link is Up - 1000/Full
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Welcome to Freescale Semiconductor Embedded Linux Environment
!!!!! WARNING !!!!!!!
The default password for the root account is: root
please change this password using the 'passwd' command
and then edit this message (/etc/issue) to remove this message
P2020RDB login: PHY: md...@520:01 - Link is Up - 1000/Full
ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
root
Password:
[r...@p2020rdb /root]# ifco[r...@p2020rdb /root]# ifconfig eth0 down
[r...@p2020rdb /root]# [r...@p2020rdb /root]# ifconfig eth0 down down 1
down down
[r...@p2020rdb /root]# [r...@p2020rdb /root]# ifconfig eth1 down down 2
down down
[r...@p2020rdb /root]#
[r...@p2020rdb /root]#
[r...@p2020rdb /root]# ifco[r...@p2020rdb /root]# ifconfig eth0 192.168.1.2 netmask 255.255.255.0
[r...@p2020rdb /root]# PHY: 0:01 - Link is Up - 1000/Full
[r...@p2020rdb /root]# ifcoe [r...@p2020rdb /root]# ifconfig t eyh
th2 192.168.2.2 netmask 255.255.255.0
[r...@p2020rdb /root]# PHY: md...@520:01 - Link is Up - 1000/Full
[r...@p2020rdb /root]# ifco[r...@p2020rdb /root]# ifconfig eth eccho 1 > /p[r...@p2020rdb /root]# eccho 1 > /proc/sy[r...@p2020rdb /root]# eccho 1 > /proc/sys/n[r...@p2020rdb /root]# eccho 1 > /proc/sys/net/ip[r...@p2020rdb /root]# eccho 1 > /proc/sys/net/ipv4[r...@p2020rdb /root]# eccho 1 > /proc/sys/net/ipv4/ip_f[r...@p2020rdb /root]# eccho 1 > /proc/sys/net/ipv4/ip_forward
-sh: eccho: not found
[r...@p2020rdb /root]# echo 1 > /p[r...@p2020rdb /root]# echo 1 > /proc/sy[r...@p2020rdb /root]# echo 1 > /proc/sys/n[r...@p2020rdb /root]# echo 1 > /proc/sys/net/ip[r...@p2020rdb /root]# echo 1 > /proc/sys/net/ipv4[r...@p2020rdb /root]# echo 1 > /proc/sys/net/ipv4/ip_f[r...@p2020rdb /root]# echo 1 > /proc/sys/net/ipv4/ip_forward
[r...@p2020rdb /root]#
[r...@p2020rdb /root]#
[r...@p2020rdb /root]# pn ing 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
64 bytes from 192.168.1.1: seq=0 ttl=255 time=2.590 ms
64 bytes from 192.168.1.1: seq=1 ttl=255 time=0.090 ms
--- 192.168.1.1 ping statistics ---
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.090/1.340/2.590 ms
[r...@p2020rdb /root]#
[r...@p2020rdb /root]#
[r...@p2020rdb /root]# ping 192.168.2.1
PING 192.168.2.1 (192.168.2.1): 56 data bytes
64 bytes from 192.168.2.1: seq=0 ttl=255 time=3.502 ms
--- 192.168.2.1 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 3.502/3.502/3.502 ms
[r...@p2020rdb /root]# arp
gateway2 (192.168.2.1) at 00:00:08:00:00:01 [ether] on eth2
gateway1 (192.168.1.1) at 00:00:07:00:00:01 [ether] on eth0
[r...@p2020rdb /root]# arp -s 192.168.2.1 00:00:08:00:00:01
[r...@p2020rdb /root]# arp -s 192.1681. .1.1 00:00:07:00:00:01
[r...@p2020rdb /root]#
[r...@p2020rdb /root]#
[r...@p2020rdb /root]#
[r...@p2020rdb /root]# arp
gateway2 (192.168.2.1) at 00:00:08:00:00:01 [ether] PERM on eth2
gateway1 (192.168.1.1) at 00:00:07:00:00:01 [ether] PERM on eth0
[r...@p2020rdb /root]# ifco[r...@p2020rdb /root]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:04:9F:0C:05:00
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5 errors:0 dropped:0 overruns:0 frame:0
TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:426 (426.0 B) TX bytes:1146 (1.1 KiB)
Base address:0x2000
eth2 Link encap:Ethernet HWaddr 00:04:9F:0C:05:02
inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:318 (318.0 B) TX bytes:1048 (1.0 KiB)
Base address:0xa000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[r...@p2020rdb /root]# cat /p[r...@p2020rdb /root]# cat /proc/in[r...@p2020rdb /root]# cat /proc/interrupts
CPU0 CPU1
19: 648 0 OpenPIC Level fsl-elbc
20: 0 0 OpenPIC Level fsldma-channel
21: 0 0 OpenPIC Level fsldma-channel
22: 0 0 OpenPIC Level fsldma-channel
23: 0 0 OpenPIC Level fsldma-channel
28: 0 0 OpenPIC Level ehci_hcd:usb1
29: 13 0 OpenPIC Level eth0_tx
30: 0 4 OpenPIC Level eth0_rx
31: 0 12 OpenPIC Level eth2_tx
32: 4 0 OpenPIC Level eth2_rx
33: 0 0 OpenPIC Level eth2_er
34: 0 0 OpenPIC Level eth0_er
42: 1049 0 OpenPIC Level serial
43: 0 29 OpenPIC Level i2c-mpc, i2c-mpc
45: 0 0 OpenPIC Level talitos
59: 0 2494 OpenPIC Level fsl_espi
72: 12 0 OpenPIC Level esdhc:slot0
76: 0 0 OpenPIC Level fsldma-channel
77: 0 0 OpenPIC Level fsldma-channel
78: 0 0 OpenPIC Level fsldma-channel
79: 0 0 OpenPIC Level fsldma-channel
251: 0 0 OpenPIC Edge ipi call function
252: 1253 1387 OpenPIC Edge ipi reschedule
253: 427 390 OpenPIC Edge ipi call function single
BAD: 1
[r...@p2020rdb /root]# PHY: md...@520:01 - Link is Down
PHY: md...@520:01 - Link is Up - 1000/Full
[r...@p2020rdb /root]# cat /p[r...@p2020rdb /root]# cat /proc/in[r...@p2020rdb /root]# cat /proc/interrupts
CPU0 CPU1
19: 648 0 OpenPIC Level fsl-elbc
20: 0 0 OpenPIC Level fsldma-channel
21: 0 0 OpenPIC Level fsldma-channel
22: 0 0 OpenPIC Level fsldma-channel
23: 0 0 OpenPIC Level fsldma-channel
28: 0 0 OpenPIC Level ehci_hcd:usb1
29: 56328 0 OpenPIC Level eth0_tx
30: 0 5553282 OpenPIC Level eth0_rx
31: 0 43413 OpenPIC Level eth2_tx
32: 5709572 0 OpenPIC Level eth2_rx
33: 0 0 OpenPIC Level eth2_er
34: 0 0 OpenPIC Level eth0_er
42: 1179 0 OpenPIC Level serial
43: 0 29 OpenPIC Level i2c-mpc, i2c-mpc
45: 0 0 OpenPIC Level talitos
59: 0 2494 OpenPIC Level fsl_espi
72: 12 0 OpenPIC Level esdhc:slot0
76: 0 0 OpenPIC Level fsldma-channel
77: 0 0 OpenPIC Level fsldma-channel
78: 0 0 OpenPIC Level fsldma-channel
79: 0 0 OpenPIC Level fsldma-channel
251: 0 0 OpenPIC Edge ipi call function
252: 1254 1389 OpenPIC Edge ipi reschedule
253: 427 406 OpenPIC Edge ipi call function single
BAD: 36172
[r...@p2020rdb /root]# uname -a
Linux P2020RDB 2.6.29 #1 SMP Fri Jul 3 15:11:50 IST 2009 ppc unknown
[r...@p2020rdb /root]# cat /p[r...@p2020rdb /root]# cat /proc/in[r...@p2020rdb /root]# cat /proc/interrupts
CPU0 CPU1
19: 648 0 OpenPIC Level fsl-elbc
20: 0 0 OpenPIC Level fsldma-channel
21: 0 0 OpenPIC Level fsldma-channel
22: 0 0 OpenPIC Level fsldma-channel
23: 0 0 OpenPIC Level fsldma-channel
28: 0 0 OpenPIC Level ehci_hcd:usb1
29: 56328 0 OpenPIC Level eth0_tx
30: 0 5553282 OpenPIC Level eth0_rx
31: 0 43413 OpenPIC Level eth2_tx
32: 5709572 0 OpenPIC Level eth2_rx
33: 0 0 OpenPIC Level eth2_er
34: 0 0 OpenPIC Level eth0_er
42: 1329 0 OpenPIC Level serial
43: 0 29 OpenPIC Level i2c-mpc, i2c-mpc
45: 0 0 OpenPIC Level talitos
59: 0 2494 OpenPIC Level fsl_espi
72: 12 0 OpenPIC Level esdhc:slot0
76: 0 0 OpenPIC Level fsldma-channel
77: 0 0 OpenPIC Level fsldma-channel
78: 0 0 OpenPIC Level fsldma-channel
79: 0 0 OpenPIC Level fsldma-channel
251: 0 0 OpenPIC Edge ipi call function
252: 1256 1391 OpenPIC Edge ipi reschedule
253: 427 439 OpenPIC Edge ipi call function single
BAD: 36172
[r...@p2020rdb /root]# ifco[r...@p2020rdb /root]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:04:9F:0C:05:00
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8928576 errors:0 dropped:0 overruns:0 frame:0
TX packets:8928586 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:625000396 (596.0 MiB) TX bytes:535715406 (510.8 MiB)
Base address:0x2000
eth2 Link encap:Ethernet HWaddr 00:04:9F:0C:05:02
inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8928575 errors:0 dropped:0 overruns:0 frame:0
TX packets:8928585 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:625000288 (596.0 MiB) TX bytes:535715308 (510.8 MiB)
Base address:0xa000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[r...@p2020rdb /root]#
------------------------------------------------------------------------
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
