Hi,
I checked the RCW(RCWLR and RCWHR) and they are the same(taken from
NOR), S3 and S4 switches are the same too.
I will take a look at the priority levels on CSB.
Regards,
Asen
Liu Dave-R63238 wrote:
One possible cause is the two board has different RCW.
So that the freq of core/csb/.... Is different.
-----Original Message-----
From:
linuxppc-dev-bounces+daveliu=freescale....@lists.ozlabs.org
[mailto:linuxppc-dev-bounces+daveliu=freescale....@lists.ozlab
s.org] On Behalf Of RONETIX - Asen Dimov
Sent: Tuesday, December 22, 2009 6:28 AM
To: linuxppc-dev@lists.ozlabs.org
Subject: MPC8313e RDB rev A4 and rev C network throughput
Hello all,
I have made some test on network throughput with MPC8313e RDB
revA4 and revC.
Some have mentioned that CSB(Coherent System Bus) frequency
or untuned TCP/IP stack, could cause decrease of network throughput.
**Test results
-on MPC8313e RDB revA4 with kernel 2.6.20 and u-boot 1.1.6
created with
ltib-mpc8313erdb-20070824
iperf -c 172.16.0.1 -l 2m -w 256k -throughput is 510Mbps
-on MPC8313e RDB revA4 with kernel 2.6.23 and u-boot 1.3.0 generated
with ltib-mpc8313erdb-20081222
iperf -c 172.16.0.1 -l 2m -w 256k
-throughput is 510Mbps
-on MPC8313e RDB revC with kernel 2.6.23 (the same u-boot, kernel and
rootfs as in rev A4, only dtb file differs)
iperf -c 172.16.0.1 -l 2m -w 256k
-throughput is 360Mbps.
Have someone made such measurements? Any ideas why MPC8313e RDB revC
gives worser throughput than revA4?
** Notes
*The PC (CPU:Intel(R) Core(TM)2 Duo CPU, E8400 @ 3.00GHz;
RAM: 2x2G DDR2 @ 800Mhz ;
NIC: R8168B PCI Express Gigabit Ethernet controller, driver
8.014.00-NAPI;
OS: Fedora release 10 (Cambridge) with kernel:
2.6.27.38-170.2.113.fc10.i686.PAE #1 SMP )
*Commnads to set PC
ethtool -s eth0 autoneg off speed 1000 duplex full
ifconfig eth1 172.16.0.1/12 mtu 6000 txqueuelen 10000
echo 131071 > /proc/sys/net/core/rmem_max
echo 131071 > /proc/sys/net/core/wmem_max
echo "4096 1048576 8388608" > /proc/sys/net/ipv4/tcp_rmem
echo "4096 1048576 8388608" > /proc/sys/net/ipv4/tcp_wmem
iperf -s -l 2m -w 70k
*The MPC8313e RDB(CPU: 333Mhz; CSB: 166Mhz) revA4 and
revC(using PHY not
switch)
*Commnads to set a board before using iperf
ifconfig eth1 172.16.0.1/12 mtu 6000 txqueuelen 10000
#The PC lan card is set to advertise 1000Mbps only, so the
board switches to 1000Mbps too.
echo 131071 > /proc/sys/net/core/rmem_max
echo 131071 > /proc/sys/net/core/wmem_max
echo "4096 1048576 8388608" > /proc/sys/net/ipv4/tcp_rmem
echo "4096 1048576 8388608" > /proc/sys/net/ipv4/tcp_wmem
Regards,
Asen
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
