Hi all,
Here is purposed bindings draft for the new drivers that I would like to
send for this or next merge window, depending on results of this RFC. ;-)
(The new bindings needs to be in-tree or at least Acked before I could
send the drivers.)
Comments and suggestions are highly appreciated.
Thanks.
diff --git a/Documentation/powerpc/booting-without-of.txt
b/Documentation/powerpc/booting-without-of.txt
index c350623..38fe3e9 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -59,6 +59,11 @@ Table of Contents
p) Freescale Synchronous Serial Interface
q) USB EHCI controllers
r) Freescale General-purpose Timers Module
+ s) Freescale USB Parameter RAM:
+ t) Freescale QUICC Engine USB Controller
+ u) LEDs on GPIOs
+ v) Freescale MCU with MPC8349E-mITX compatible firmware
+ w) NAND on UPM-driven Freescale Localbus
VII - Marvell Discovery mv64[345]6x System Controller chips
1) The /system-controller node
@@ -2866,6 +2871,139 @@ platforms are moved over to use the
flattened-device-tree model.
clock-frequency = <0>;
};
+ s) Freescale USB Parameter RAM:
+
+ Required properties:
+ - compatible : should be "fsl,<chip>-qe-muram-usb-pram",
+ "fsl,qe-muram-usb-pram", "fsl,cpm-muram-usb-pram".
+ - reg : should contain USB PRAM location and length.
+
+ Example:
+
+ [EMAIL PROTECTED] {
+ compatible = "fsl,mpc8360-qe-muram-usb-pram",
+ "fsl,qe-muram-usb-pram",
+ "fsl,cpm-muram-usb-pram";
+ reg = <0x8b00 0x100>;
+ };
+
+ t) Freescale QUICC Engine USB Controller
+
+ Required properties:
+ - compatible : should be "fsl,<chip>-qe-usb", "fsl,qe-usb",
+ "fsl,usb-fhci"
+ - reg : should contain gtm registers location and length.
+ - interrupts : should contain USB interrupt.
+ - interrupt-parent : interrupt source phandle.
+ - fsl,fullspeed-clock : specifies the full speed USB clock source.
+ - fsl,lowspeed-clock : specifies the low speed USB clock source.
+ - fsl,usb-mode : should be "host".
+ - linux,hub-power-budget : optional, USB power budget for the root hub
+ in mA.
+ - gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP,
+ USBRN, SPEED (optional), and SUSPEND (optional).
+
+ Example:
+
+ [EMAIL PROTECTED] {
+ compatible = "fsl,mpc8360-qe-usb", "fsl,qe-usb",
+ "fsl,usb-fhci";
+ reg = <0x6c0 0x40>;
+ interrupts = <11>;
+ interrupt-parent = <&qeic>;
+ fsl,fullspeed-clock = "clk21";
+ fsl,usb-mode = "host";
+ gpios = <&qe_pio_b 2 0 /* USBOE */
+ &qe_pio_b 3 0 /* USBTP */
+ &qe_pio_b 8 0 /* USBTN */
+ &qe_pio_b 9 0 /* USBRP */
+ &qe_pio_b 11 0 /* USBRN */
+ &qe_pio_e 20 0 /* SPEED */
+ &qe_pio_e 21 0 /* SUSPN */>;
+ };
+
+ u) LEDs on GPIOs
+
+ Required properties:
+ - compatible : should be "linux,gpio-led".
+ - linux,name : LED name.
+ - linux,active-low : property should be present if LED wired as
+ active-low.
+ - linux,default-trigger : Linux default trigger for this LED.
+ - linux,brightness : default brightness.
+ - gpios : should specify LED GPIO.
+
+ Example:
+
+ [EMAIL PROTECTED] {
+ compatible = "linux,gpio-led";
+ linux,name = "pwr";
+ linux,brightness = <1>;
+ linux,active-low;
+ gpios = <&mcu_pio 0>;
+ };
+
+ [EMAIL PROTECTED] {
+ compatible = "linux,gpio-led";
+ linux,name = "hdd";
+ linux,default-trigger = "ide-disk";
+ linux,active-low;
+ gpios = <&mcu_pio 1>;
+ };
+
+ v) Freescale MCU with MPC8349E-mITX compatible firmware
+
+ Required properties:
+ - compatible : "fsl,<mcu-chip>-<board>", "fsl,mcu-mpc8349emitx",
+ "simple-bus";
+ - reg : should specify I2C address (0x0a).
+ - #address-cells : should be 0.
+ - #size-cells : should be 0.
+ - #gpio-cells : should be 1.
+ - gpio-controller : should be present;
+
+ Example:
+
+ mcu_pio: [EMAIL PROTECTED] {
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #gpio-cells = <1>;
+ compatible = "fsl,mc9s08qg8-mpc8349emitx",
+ "fsl,mcu-mpc8349emitx",
+ "simple-bus";
+ reg = <0x0a>;
+ gpio-controller;
+ };
+
+ w) NAND on UPM-driven Freescale Localbus
+
+ Required properties:
+ - compatible : "fsl,upm-nand".
+ - reg : should specify localbus chip select and size used for the chip.
+ - width : should specify port size in bytes.
+ - fsl,upm-addr-offset : UPM pattern offset for the address latch.
+ - fsl,upm-cmd-offset : UPM pattern offset for the command latch.
+ - fsl,wait-pattern : should be present if NAND chip requires waiting
+ for Ready-Not-Busy pin after each executed pattern.
+ - fsl,wait-write : should be present if NAND chip needs waiting on
+ Ready-Not-Busy pin after each write cycle.
+ - linux,chip-delay : optional, may contain delay value in milliseconds
+ (in case when Ready-Not-Busy pin was unspecified).
+ - gpios : may specify optional GPIO connected to the Ready-Not-Busy pin.
+
+ Example:
+
+ [EMAIL PROTECTED],0 {
+ compatible = "stmicro,NAND512W3A2BN6E", "fsl,upm-nand";
+ reg = <1 0 1>;
+ width = <1>;
+ fsl,upm-addr-offset = <16>;
+ fsl,upm-cmd-offset = <8>;
+ fsl,wait-pattern;
+ fsl,wait-write;
+ gpios = <&qe_pio_e 18 0>;
+ };
+
VII - Marvell Discovery mv64[345]6x System Controller chips
===========================================================
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
