Currently, all non TAH equipped 4xx PPC's call emac_start_xmit() upon
xmit. This routine doesn't check if the frame length exceeds the max.
MAL buffer size.
This patch now changes the driver to call emac_start_xmit_sg() on all
GigE platforms and not only the TAH equipped ones (440GX). This enables
an MTU of 9000 instead 4080.
Signed-off-by: Stefan Roese <[EMAIL PROTECTED]>
---
drivers/net/ibm_newemac/core.c | 14 ++++----------
1 files changed, 4 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ibm_newemac/core.c b/drivers/net/ibm_newemac/core.c
index cb06280..b24bd2d 100644
--- a/drivers/net/ibm_newemac/core.c
+++ b/drivers/net/ibm_newemac/core.c
@@ -1297,7 +1297,6 @@ static int emac_start_xmit(struct sk_buff *skb, struct
net_device *ndev)
return emac_xmit_finish(dev, len);
}
-#ifdef CONFIG_IBM_NEW_EMAC_TAH
static inline int emac_xmit_split(struct emac_instance *dev, int slot,
u32 pd, int len, int last, u16 base_ctrl)
{
@@ -1410,9 +1409,6 @@ static int emac_start_xmit_sg(struct sk_buff *skb, struct
net_device *ndev)
DBG2(dev, "stopped TX queue" NL);
return 1;
}
-#else
-# define emac_start_xmit_sg emac_start_xmit
-#endif /* !defined(CONFIG_IBM_NEW_EMAC_TAH) */
/* Tx lock BHs */
static void emac_parse_tx_error(struct emac_instance *dev, u16 ctrl)
@@ -2683,13 +2679,8 @@ static int __devinit emac_probe(struct of_device *ofdev,
/* Fill in the driver function table */
ndev->open = &emac_open;
-#ifdef CONFIG_IBM_NEW_EMAC_TAH
- if (dev->tah_dev) {
- ndev->hard_start_xmit = &emac_start_xmit_sg;
+ if (dev->tah_dev)
ndev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
- } else
-#endif
- ndev->hard_start_xmit = &emac_start_xmit;
ndev->tx_timeout = &emac_tx_timeout;
ndev->watchdog_timeo = 5 * HZ;
ndev->stop = &emac_close;
@@ -2697,8 +2688,11 @@ static int __devinit emac_probe(struct of_device *ofdev,
ndev->set_multicast_list = &emac_set_multicast_list;
ndev->do_ioctl = &emac_ioctl;
if (emac_phy_supports_gige(dev->phy_mode)) {
+ ndev->hard_start_xmit = &emac_start_xmit_sg;
ndev->change_mtu = &emac_change_mtu;
dev->commac.ops = &emac_commac_sg_ops;
+ } else {
+ ndev->hard_start_xmit = &emac_start_xmit;
}
SET_ETHTOOL_OPS(ndev, &emac_ethtool_ops);
--
1.5.4.rc3
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
