Josh Boyer wrote:
Can you post the full boot messages (send privately if you'd like). One
thing to make sure of is if all the properties in the DTS file that say
"Filled in by zImage wrapper" are actually getting filled in.
I have attached a boot log. The ethernet and IP addresses have been
modified, but everything else is correct.
I checked all the dts entries marked by /* Filled in by zImage */ by
checking /proc/device-tree and they all match what is printed after the
log message "Uncompressing Kernel Image ... OK".
FYI: It is a 533MHz PPC but the HW guys read the spec wrong and are
running the system clock at 66.0MHz rather than 66.6MHz, so the 528MHz
value is correct.
Cheers,
Sean
U-Boot 1.3.0-gf92edbd8-dirty (Dec 7 2007 - 11:06:34)
CPU: AMCC PowerPC 440EP Rev. C at 533.333 MHz (PLB=133, OPB=66, EBC=66 MHz)
I2C boot EEPROM enabled
Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
, PCI async ext clock used 32 kB I-Cache 32 kB D-Cache
Board: PIKA Embedded Appliance
I2C: ready
DRAM: 256 MB
FLASH: 64 MB
NAND: 64 MiB
In: serial
Out: serial
Err: serial
Protected 2 sectors
FPGA download...complete.
FPGA code revision 1.2.2.0
Starting board diagnostics:
1. RAM walking bit test, first bank... test complete.
2. RAM walking bit test, second bank... test complete.
3. FPGA walking bit test... test complete.
4. Skipping user test - start_test_addr or end_test_addr env. vars not set.
Board diagnostics complete.
Net: ppc_4xx_eth0
Type "run flash_nfs" to mount root filesystem over NFS
Hit any key to stop autoboot: 0
Waiting for PHY auto negotiation to complete. done
ENET Speed is 100 Mbps - FULL duplex connection (EMAC0)
Using ppc_4xx_eth0 device
TFTP from server 192.168.0.164; our IP address is 192.168.0.99
Filename 'uImage'.
Load address: 0x200000
Loading: #################################################################
#################################################################
#################################################################
#############################################################
done
Bytes transferred = 1308159 (13f5ff hex)
## Booting image at 00200000 ...
Image Name: Linux-2.6.24-rc6-pika
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1308095 Bytes = 1.2 MB
Load Address: 00400000
Entry Point: 004003c8
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
CPU clock-frequency <- 0x1f78a400 (528MHz)
CPU timebase-frequency <- 0x1f78a400 (528MHz)
/plb: clock-frequency <- 7de2900 (132MHz)
/plb/opb: clock-frequency <- 3ef1480 (66MHz)
/plb/opb/ebc: clock-frequency <- 3ef1480 (66MHz)
/plb/opb/[EMAIL PROTECTED]: clock-frequency <- a8c000 (11MHz)
Memory <- <0x0 0x0 0x10000000> (256MB)
ENET0: local-mac-address <- <mac address>
zImage starting: loaded at 0x00400000 (sp: 0x0ff2a558)
Allocating 0x2b84a0 bytes for kernel ...
gunzipping (0x00000000 <- 0x0040d000:0x006ba364)...done 0x297408 bytes
Linux/PowerPC load: root=/dev/nfs rw nfsroot=192.168.x.x:/usr/src/eldk/taco
ip=192.168.x.x:192.168.x.x:192.168.x.x:255.255.252.0:tigger:eth0:off panic=1
console=ttyS0,1150
Finalizing device tree... flat tree at 0x6c7300
Using Taco machine description
Linux version 2.6.24-rc6-pika ([EMAIL PROTECTED]) (gcc version 4.0.0 (DENX ELDK
4.1 4.0.0)) #14 Thu Dec 27 16:33:16 EST 2007
console [udbg0] enabled
setup_arch: bootmem
arch: exit
Zone PFN ranges:
DMA 0 -> 65536
Normal 65536 -> 65536
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 65536
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: root=/dev/nfs rw nfsroot=192.168.x.x:/usr/src/eldk/taco
ip=192.168.x.x:192.168.x.x:192.168.x.x:255.255.252.0:tigger:eth0:off panic=1
console=ttyS0,110
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
PID hash table entries: 1024 (order: 10, 4096 bytes)
clocksource: timebase mult[79364e] shift[22] registered
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256768k/262144k available (2516k kernel code, 5056k reserved, 116k
data, 129k bss, 140k init)
Mount-cache hash table entries: 512
net_namespace: 64 bytes
NET: Registered protocol family 16
SCSI subsystem initialized
NET: Registered protocol family 2
Time: timebase clocksource has been installed.
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
JFFS2 version 2.2. (NAND) .. 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xef600300 (irq = 16) is a 16550A
console handover:
boot [udbg0] -> real [ttyS0]
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPC 4xx OCP EMAC driver, version 3.54
MAL v1 /plb/mcmal, 4 TX channels, 2 RX channels
ZMII /plb/opb/[EMAIL PROTECTED] initialized
/plb/opb/[EMAIL PROTECTED]: bridge in RMII mode
eth0: EMAC-0 /plb/opb/[EMAIL PROTECTED], MAC 00:1e:84:ff:n.n
eth0: found Generic MII PHY (0x01)
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <[EMAIL PROTECTED]>
All bugs added by David S. Miller <[EMAIL PROTECTED]>
eth0: link is down
IP-Config: Complete:
device=eth0, addr=192.168.x.x, mask=255.255.252.0, gw=192.168.x.x,
host=tigger, domain=, nis-domain=(none),
bootserver=192.168.x.x, rootserver=192.168.x.x, rootpath=
Looking up port of RPC 100003/2 on 192.168.x.x
eth0: link is up, 100 FDX, pause enabled
Looking up port of RPC 100005/1 on 192.168.x.x
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 140k init
init started: BusyBox v1.6.1 (2007-09-17 15:31:56 EDT) multi-call binary
starting pid 16, tty '': '/sbin/syslogd'
starting pid 19, tty '': '/etc/rc.S'
starting pid 28, tty '': '/sbin/getty'
tigger login:
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
