PowerPC 44x NanD Flash Controller (NDFC) bindings.
Signed-off-by: Valentine Barshak <[EMAIL PROTECTED]>
---
Documentation/powerpc/booting-without-of.txt | 64 +++++++++++++++++++++++++++
1 files changed, 64 insertions(+)
--- linux-2.6.orig/Documentation/powerpc/booting-without-of.txt 2007-10-29
16:02:07.000000000 +0300
+++ linux-2.6/Documentation/powerpc/booting-without-of.txt 2007-10-29
21:34:14.000000000 +0300
@@ -52,6 +52,7 @@ Table of Contents
i) Freescale QUICC Engine module (QE)
j) CFI or JEDEC memory-mapped NOR flash
k) Global Utilities Block
+ l) 44x NanD Flash Controller (NDFC)
VII - Specifying interrupt information for devices
1) interrupts property
@@ -2242,6 +2243,69 @@ platforms are moved over to use the flat
available.
For Axon: 0x0000012a
+ l) 44x NanD Flash Controller (NDFC)
+
+ Required properties:
+ - compatible : should be "ibm,ndfc".
+ - reg : should contain address and length of the NDFC registers.
+
+ ndfc node should contain at least one ndfc-mtd sub-node describing
+ chip properties and bank settings for the chip(s) attached to particular
+ ndfc bank(s).
+
+ Required ndfc-mtd properties:
+ - bank-map : at least one value (less than number of NDFC banks available)
+ identifying bank number the chip is attached to. If we have several
+ identical chips and want to spread a single mtd device across all of them,
+ we need to specify here the bank numbers the chips are attached to.
+ E.g. "bank-map = <0 3>;" means a single mtd device will be created
+ for 2 identical NAND chips attached to banks 0 and 3 of the NDFC.
+ Optional ndfc-mtd properties:
+ - chip-options : NAND chip options.
+ - chip-delay : NAND chip delay. Default is 50us.
+ - bank-settings : NDFC bank settings for the chip(s). This value is
+ written to the NDFC Bank Configuration Register.
+ If not specified, the default timings (RR=RWH=RWP=CRW=2) and
+ bank width from the "bank-width" property will be used for the chip.
+ - bank-width : NAND chip bus width. Should be 1 for 8-bit NAND or
+ 2 for 16-bit NAND. By default an 8-bit width is set.
+ - #address-cells, #size-cells : Must be present if the flash has
+ sub-nodes representing partitions (see below). In this case
+ both #address-cells and #size-cells must be equal to 1.
+
+ ndfc_mtd can have partition sub-nodes, which are described the same way
+ as for the CFI or JEDEC memory-mapped NOR flash.
+
+ Example (Sequoia 440EPx):
+ NDFC is relocatable within EBC and should have EBC as a parent node.
+ Here we have NDFC on EBC CS3 bank and one NAND chip attached to bank 3
+ of the NanD Flash Controller:
+
+ [EMAIL PROTECTED],0 {
+ compatible = "ibm,ndfc-440epx", "ibm,ndfc";
+ reg = <3 000000 2000>;
+ ndfc-mtd0 {
+ bank-settings = <80002222>;
+ bank-map = <3>;
+ chip-delay = <32>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ [EMAIL PROTECTED] {
+ label = "u-boot-nand";
+ reg = <0 0080000>;
+ };
+ [EMAIL PROTECTED] {
+ label = "kernel-nand";
+ reg = <0080000 0180000>;
+ };
+ [EMAIL PROTECTED] {
+ label = "filesystem";
+ reg = <0200000 1e00000>;
+ };
+ };
+ };
+
+
More devices will be defined as this spec matures.
VII - Specifying interrupt information for devices
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
