cuboot-pq2 is updated to match the binding, and get rid of phandle linkage.
Signed-off-by: Scott Wood <[EMAIL PROTECTED]>
---
Documentation/powerpc/booting-without-of.txt | 38 ++++++++++++++++++++++++++
arch/powerpc/boot/cuboot-pq2.c | 29 +++++--------------
2 files changed, 46 insertions(+), 21 deletions(-)
diff --git a/Documentation/powerpc/booting-without-of.txt
b/Documentation/powerpc/booting-without-of.txt
index a599f1a..42cbfb0 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -2017,6 +2017,44 @@ platforms are moved over to use the
flattened-device-tree model.
fsl,cpm-command = <2e600000>;
};
+ m) Chipselect/Local Bus
+
+ Properties:
+ - name : Should be localbus
+ - #address-cells : Should be either two or three. The first cell is the
+ chipselect number, and the remaining cells are the
+ offset into the chipselect.
+ - #size-cells : Either one or two, depending on how large each chipselect
+ can be.
+ - ranges : Each range should correspond to a single chipselect, and cover
+ the entire access window as configured.
+
+ Example:
+ [EMAIL PROTECTED] {
+ compatible = "fsl,mpc8272ads-localbus",
+ "fsl,mpc8272-localbus",
+ "fsl,pq2-localbus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <f0010100 40>;
+
+ ranges = <0 0 fe000000 02000000
+ 1 0 f4500000 00008000>;
+
+ [EMAIL PROTECTED],0 {
+ compatible = "jedec-flash";
+ reg = <0 0 2000000>;
+ bank-width = <4>;
+ device-width = <1>;
+ };
+
+ [EMAIL PROTECTED],0 {
+ reg = <1 0 20>;
+ compatible = "fsl,mpc8272ads-bcsr";
+ };
+ };
+
+
More devices will be defined as this spec matures.
VII - Specifying interrupt information for devices
diff --git a/arch/powerpc/boot/cuboot-pq2.c b/arch/powerpc/boot/cuboot-pq2.c
index b150bd4..e5d94ff 100644
--- a/arch/powerpc/boot/cuboot-pq2.c
+++ b/arch/powerpc/boot/cuboot-pq2.c
@@ -43,22 +43,21 @@ struct pci_range pci_ranges_buf[MAX_PROP_LEN /
sizeof(struct pci_range)];
* some don't set up the PCI PIC at all, so we assume the device tree is
* sane and update the BRx registers appropriately.
*
- * For any node defined as compatible with fsl,pq2-chipselect,
- * #address/#size must be 2/1 for chipselect bus, 1/1 for parent bus,
- * and ranges must be for whole chip selects.
+ * For any node defined as compatible with fsl,pq2-localbus,
+ * #address/#size must be 2/1 for the localbus, and 1/1 for the parent bus.
+ * Ranges must be for whole chip selects.
*/
static void update_cs_ranges(void)
{
- u32 ctrl_ph;
- void *ctrl_node, *bus_node, *parent_node;
+ void *bus_node, *parent_node;
u32 *ctrl_addr;
unsigned long ctrl_size;
u32 naddr, nsize;
int len;
int i;
- bus_node = finddevice("/chipselect");
- if (!bus_node || !dt_is_compatible(bus_node, "fsl,pq2-chipselect"))
+ bus_node = finddevice("/localbus");
+ if (!bus_node || !dt_is_compatible(bus_node, "fsl,pq2-localbus"))
return;
dt_get_reg_format(bus_node, &naddr, &nsize);
@@ -73,19 +72,7 @@ static void update_cs_ranges(void)
if (naddr != 1 || nsize != 1)
goto err;
- len = getprop(bus_node, "fsl,ctrl", &ctrl_ph, 4);
- if (len != 4)
- goto err;
-
- ctrl_node = find_node_by_prop_value(NULL, "linux,phandle",
- (char *)&ctrl_ph, 4);
- if (!ctrl_node)
- goto err;
-
- if (!dt_is_compatible(ctrl_node, "fsl,pq2-chipselect-ctrl"))
- goto err;
-
- if (!dt_xlate_reg(ctrl_node, 0, (unsigned long *)&ctrl_addr,
+ if (!dt_xlate_reg(bus_node, 0, (unsigned long *)&ctrl_addr,
&ctrl_size))
goto err;
@@ -122,7 +109,7 @@ static void update_cs_ranges(void)
return;
err:
- printf("Bad /chipselect or fsl,pq2-chipselect-ctrl node\r\n");
+ printf("Bad /localbus node\r\n");
}
/* Older u-boots don't set PCI up properly. Update the hardware to match
--
1.5.3.1
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
