David Miller wrote:
> From: James Chapman <[EMAIL PROTECTED]>
> Date: Sun, 26 Aug 2007 20:36:20 +0100
>
>> David Miller wrote:
>>> From: James Chapman <[EMAIL PROTECTED]>
>>> Date: Fri, 24 Aug 2007 18:16:45 +0100
>>>
>>>> Does hardware interrupt mitigation really interact well with NAPI?
>>> It interacts quite excellently.
>> If NAPI disables interrupts and keeps them disabled while there are more
>> packets arriving or more transmits being completed, why do hardware
>> interrupt mitigation / coalescing features of the network silicon help?
>
> Because if your packet rate is low enough such that the cpu can
> process the interrupt fast enough and thus only one packet gets
> processed per NAPI poll, the cost of going into and out of NAPI mode
> dominates the packet processing costs.
In the second half of my previous reply (which seems to have been
deleted), I suggest a way to avoid this problem without using hardware
interrupt mitigation / coalescing. Original text is quoted below.
>> I've seen the same and I'm suggesting that the NAPI driver keeps
>> itself in polled mode for N polls or M jiffies after it sees
>> workdone=0. This has always worked for me in packet forwarding
>> scenarios to maximize packets/sec and minimize latency.
To implement this, there's no need for timers, hrtimers or generic NAPI
support that others have suggested. A driver's poll() would set an
internal flag and record the current jiffies value when finding
workdone=0 rather than doing an immediate napi_complete(). Early in
poll() it would test this flag and if set, do a low-cost test to see if
it had any work to do. If no work, it would check the saved jiffies
value and do the napi_complete() only if no work has been done for a
configurable number of jiffies. This keeps interrupts disabled longer at
the expense of many more calls to poll() where no work is done. So
critical to this scheme is modifying the driver's poll() to fastpath the
case of having no work to do while waiting for its local jiffy count to
expire.
Here's an untested patch for tg3 that illustrates the idea.
diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
index 710dccc..59e151b 100644
--- a/drivers/net/tg3.c
+++ b/drivers/net/tg3.c
@@ -3473,6 +3473,24 @@ static int tg3_poll(struct napi_struct *napi,
struct tg3_hw_status *sblk = tp->hw_status;
int work_done = 0;
+ /* fastpath having no work while we're holding ourself in
+ * polled mode
+ */
+ if ((tp->exit_poll_time) && (!tg3_has_work(tp))) {
+ if (time_after(jiffies, tp->exit_poll_time)) {
+ tp->exit_poll_time = 0;
+ /* tell net stack and NIC we're done */
+ netif_rx_complete(netdev, napi);
+ tg3_restart_ints(tp);
+ }
+ return 0;
+ }
+
+ /* if we get here, there might be work to do so disable the
+ * poll hold fastpath above
+ */
+ tp->exit_poll_time = 0;
+
/* handle link change and other phy events */
if (!(tp->tg3_flags &
(TG3_FLAG_USE_LINKCHG_REG |
@@ -3511,11 +3529,11 @@ static int tg3_poll(struct napi_struct *napi,
} else
sblk->status &= ~SD_STATUS_UPDATED;
- /* if no more work, tell net stack and NIC we're done */
- if (!tg3_has_work(tp)) {
- netif_rx_complete(netdev, napi);
- tg3_restart_ints(tp);
- }
+ /* if no more work, set the time in jiffies when we should
+ * exit polled mode
+ */
+ if (!tg3_has_work(tp))
+ tp->exit_poll_time = jiffies + 2;
return work_done;
}
diff --git a/drivers/net/tg3.h b/drivers/net/tg3.h
index a6a23bb..a0d24d3 100644
--- a/drivers/net/tg3.h
+++ b/drivers/net/tg3.h
@@ -2163,6 +2163,7 @@ struct tg3 {
u32 last_tag;
u32 msg_enable;
+ unsigned long exit_poll_time;
/* begin "tx thread" cacheline section */
void (*write32_tx_mbox) (struct tg3 *, u32,
--
James Chapman
Katalix Systems Ltd
http://www.katalix.com
Catalysts for your Embedded Linux software development
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
