Hello,
kernel:
4.14.0-041400rc8-generic
dmesg:
[ 8517.739152] xhci_hcd 0000:00:14.0: Cannot set link state.
[ 8517.739203] usb usb4-port2: cannot disable (err = -32)
[ 8517.739216] usb 4-2: USB disconnect, device number 2
Regards,
--
Cristian
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor
Family DRAM Controller [8086:0104] (rev 09)
Subsystem: Samsung Electronics Co Ltd 2nd Generation Core Processor
Family DRAM Controller [144d:c0d7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core
Processor Family Integrated Graphics Controller [8086:0116] (rev 09) (prog-if
00 [VGA controller])
Subsystem: Samsung Electronics Co Ltd 2nd Generation Core Processor
Family Integrated Graphics Controller [144d:c0d7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 27
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 3000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Samsung Electronics Co Ltd 7 Series/C210 Series Chipset
Family USB xHCI Host Controller [144d:c0d7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 25
Region 0: Memory at f0600000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series
Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: Samsung Electronics Co Ltd 7 Series/C210 Series Chipset
Family MEI Controller [144d:c0d7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 28
Region 0: Memory at f0615000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Samsung Electronics Co Ltd 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller [144d:c0d7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f061a000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset
Family High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: Samsung Electronics Co Ltd 7 Series/C210 Series Chipset
Family High Definition Audio Controller [144d:c0d7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f0610000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f0500000-f05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.3 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 4 [8086:1e16] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 19
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Prefetchable memory behind bridge: 00000000f0400000-00000000f04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Samsung Electronics Co Ltd 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller [144d:c0d7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f0619000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1f.0 ISA bridge [0601]: Intel Corporation HM76 Express Chipset LPC
Controller [8086:1e59] (rev 04)
Subsystem: Samsung Electronics Co Ltd HM76 Express Chipset LPC
Controller [144d:c0d7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family
6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Samsung Electronics Co Ltd 7 Series Chipset Family 6-port
SATA Controller [AHCI mode] [144d:c0d7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 26
Region 0: I/O ports at 3088 [size=8]
Region 1: I/O ports at 3094 [size=4]
Region 2: I/O ports at 3080 [size=8]
Region 3: I/O ports at 3090 [size=4]
Region 4: I/O ports at 3060 [size=32]
Region 5: Memory at f0618000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family
SMBus Controller [8086:1e22] (rev 04)
Subsystem: Samsung Electronics Co Ltd 7 Series/C210 Series Chipset
Family SMBus Controller [144d:c0d7]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 7
Region 0: Memory at f0614000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at efa0 [size=32]
Kernel modules: i2c_i801
01:00.0 Network controller [0280]: Intel Corporation Centrino Advanced-N 6235
[8086:088e] (rev 24)
Subsystem: Intel Corporation Centrino Advanced-N 6235 AGN [8086:4060]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f0500000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
Subsystem: Samsung Electronics Co Ltd RTL8111/8168/8411 PCI Express
Gigabit Ethernet Controller [144d:c0d7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Region 0: I/O ports at 2000 [size=256]
Region 2: Memory at f0404000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at f0400000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
[ 0.000000] microcode: microcode updated early to revision 0x29, date = 2013-06-12
[ 0.000000] Linux version 4.14.0-041400rc8-generic (kernel@kathleen) (gcc version 7.2.0 (Ubuntu 7.2.0-8ubuntu3)) #201711052313 SMP Sun Nov 5 23:14:08 UTC 2017
[ 0.000000] Command line: BOOT_IMAGE=/@/boot/vmlinuz-4.14.0-041400rc8-generic root=UUID=707d0f89-4b1d-4432-9d50-6058dc4c1ee9 ro rootflags=subvol=@ quiet splash vt.handoff=7
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000003fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000040000000-0x00000000401fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000040200000-0x00000000c42a9fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000c42aa000-0x00000000c44abfff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000c44ac000-0x00000000d33eefff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d33ef000-0x00000000daeeefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000daeef000-0x00000000daf9efff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000daf9f000-0x00000000daffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000dafff000-0x00000000daffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000db000000-0x00000000df9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffd00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000031f5fffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000031f600000-0x000000031f7fffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] random: fast init done
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: SAMSUNG ELECTRONICS CO., LTD. 530U3C/530U4C/SAMSUNG_NP1234567890, BIOS P14AAJ 04/15/2013
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x31f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFC00000 mask FFFC00000 write-protect
[ 0.000000] 1 base 000000000 mask F80000000 write-back
[ 0.000000] 2 base 080000000 mask FC0000000 write-back
[ 0.000000] 3 base 0C0000000 mask FE0000000 write-back
[ 0.000000] 4 base 0DC000000 mask FFC000000 uncachable
[ 0.000000] 5 base 0DB000000 mask FFF000000 uncachable
[ 0.000000] 6 base 100000000 mask F00000000 write-back
[ 0.000000] 7 base 200000000 mask F00000000 write-back
[ 0.000000] 8 base 300000000 mask FE0000000 write-back
[ 0.000000] 9 base 31F800000 mask FFF800000 uncachable
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.000000] e820: last_pfn = 0xdb000 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f0100-0x000f010f] mapped at [fffffffffd200100]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff8ae340097000] 97000 size 24576
[ 0.000000] reserving inaccessible SNB gfx pages
[ 0.000000] BRK [0x12c323000, 0x12c323fff] PGTABLE
[ 0.000000] BRK [0x12c324000, 0x12c324fff] PGTABLE
[ 0.000000] BRK [0x12c325000, 0x12c325fff] PGTABLE
[ 0.000000] BRK [0x12c326000, 0x12c326fff] PGTABLE
[ 0.000000] BRK [0x12c327000, 0x12c327fff] PGTABLE
[ 0.000000] BRK [0x12c328000, 0x12c328fff] PGTABLE
[ 0.000000] BRK [0x12c329000, 0x12c329fff] PGTABLE
[ 0.000000] BRK [0x12c32a000, 0x12c32afff] PGTABLE
[ 0.000000] BRK [0x12c32b000, 0x12c32bfff] PGTABLE
[ 0.000000] BRK [0x12c32c000, 0x12c32cfff] PGTABLE
[ 0.000000] BRK [0x12c32d000, 0x12c32dfff] PGTABLE
[ 0.000000] BRK [0x12c32e000, 0x12c32efff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x31c53000-0x34e20fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F0120 000024 (v02 SECCSD)
[ 0.000000] ACPI: XSDT 0x00000000DAFFE170 000094 (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: FACP 0x00000000DAFEE000 00010C (v05 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: DSDT 0x00000000DAFF1000 0092DA (v02 SECCSD IVB-CPT 00000000 INTL 20061109)
[ 0.000000] ACPI: FACS 0x00000000DAF7B000 000040
[ 0.000000] ACPI: SLIC 0x00000000DAFFD000 000176 (v01 SECCSD LH43STAR 00000002 PTL 00000001)
[ 0.000000] ACPI: SSDT 0x00000000DAFFB000 001068 (v01 SECCSD PtidDevc 00001000 INTL 20061109)
[ 0.000000] ACPI: ASF! 0x00000000DAFF0000 0000A5 (v32 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: HPET 0x00000000DAFED000 000038 (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: APIC 0x00000000DAFEC000 000098 (v03 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: MCFG 0x00000000DAFEB000 00003C (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: FPDT 0x00000000DAFEA000 000054 (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: SSDT 0x00000000DAFE9000 0007D7 (v01 PmRef Cpu0Ist 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 0x00000000DAFE8000 000AD0 (v01 PmRef CpuPm 00003000 INTL 20061109)
[ 0.000000] ACPI: UEFI 0x00000000DAFE7000 00003E (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: UEFI 0x00000000DAFE6000 000042 (v01 PTL COMBUF 00000001 PTL 00000001)
[ 0.000000] ACPI: POAT 0x00000000DAF78000 000055 (v03 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: UEFI 0x00000000DAFE5000 00022E (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000031f5fffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x31f5cd000-0x31f5f7fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000031f5fffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000001fffffff]
[ 0.000000] node 0: [mem 0x0000000020200000-0x000000003fffffff]
[ 0.000000] node 0: [mem 0x0000000040200000-0x00000000c42a9fff]
[ 0.000000] node 0: [mem 0x00000000c44ac000-0x00000000d33eefff]
[ 0.000000] node 0: [mem 0x00000000dafff000-0x00000000daffffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000031f5fffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000031f5fffff]
[ 0.000000] On node 0 totalpages: 3089290
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 156 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13432 pages used for memmap
[ 0.000000] DMA32 zone: 859630 pages, LIFO batch:31
[ 0.000000] Normal zone: 34776 pages used for memmap
[ 0.000000] Normal zone: 2225664 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics memory at 0x00000000dba00000-0x00000000df9fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x40000000-0x401fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xc42aa000-0xc44abfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xd33ef000-0xdaeeefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdaeef000-0xdaf9efff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdaf9f000-0xdaffefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdb000000-0xdf9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdfa00000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed07fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed08000-0xfed08fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed09000-0xfed0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffcfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xffd00000-0xffffffff]
[ 0.000000] e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] percpu: Embedded 39 pages/cpu @ffff8ae65f200000 s119832 r8192 d31720 u262144
[ 0.000000] pcpu-alloc: s119832 r8192 d31720 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3040862
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/@/boot/vmlinuz-4.14.0-041400rc8-generic root=UUID=707d0f89-4b1d-4432-9d50-6058dc4c1ee9 ro rootflags=subvol=@ quiet splash vt.handoff=7
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 12019764K/12357160K available (9458K kernel code, 2479K rwdata, 4052K rodata, 2320K init, 2384K bss, 337396K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] ftrace: allocating 38155 entries in 150 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=8.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS: 524544, nr_irqs: 488, preallocated irqs: 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.004000] tsc: Detected 1496.482 MHz processor
[ 0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 2992.96 BogoMIPS (lpj=5985928)
[ 0.004000] pid_max: default: 32768 minimum: 301
[ 0.004000] ACPI: Core revision 20170728
[ 0.013353] ACPI: 4 ACPI AML tables successfully acquired and loaded
[ 0.013401] Security Framework initialized
[ 0.013403] Yama: becoming mindful.
[ 0.013428] AppArmor: AppArmor initialized
[ 0.016760] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.018391] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.018461] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.018512] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.018825] CPU: Physical Processor ID: 0
[ 0.018826] CPU: Processor Core ID: 0
[ 0.018832] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.018833] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.018838] mce: CPU supports 7 MCE banks
[ 0.018849] CPU0: Thermal monitoring enabled (TM1)
[ 0.018863] process: using mwait in idle threads
[ 0.018867] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[ 0.018869] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.019026] Freeing SMP alternatives memory: 36K
[ 0.022461] smpboot: Max logical packages: 4
[ 0.022542] x2apic: IRQ remapping doesn't support X2APIC mode
[ 0.023006] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.062705] TSC deadline timer enabled
[ 0.062709] smpboot: CPU0: Intel(R) Core(TM) i3-2377M CPU @ 1.50GHz (family: 0x6, model: 0x2a, stepping: 0x7)
[ 0.062804] Performance Events: PEBS fmt1+, SandyBridge events, 16-deep LBR, full-width counters, Intel PMU driver.
[ 0.062839] ... version: 3
[ 0.062840] ... bit width: 48
[ 0.062841] ... generic registers: 4
[ 0.062842] ... value mask: 0000ffffffffffff
[ 0.062843] ... max period: 00007fffffffffff
[ 0.062844] ... fixed-purpose events: 3
[ 0.062845] ... event mask: 000000070000000f
[ 0.062898] Hierarchical SRCU implementation.
[ 0.064000] smp: Bringing up secondary CPUs ...
[ 0.064000] x86: Booting SMP configuration:
[ 0.064000] .... node #0, CPUs: #1
[ 0.142044] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.142044] #2 #3
[ 0.302035] smp: Brought up 1 node, 4 CPUs
[ 0.302035] smpboot: Total of 4 processors activated (11975.85 BogoMIPS)
[ 0.304598] devtmpfs: initialized
[ 0.304598] x86/mm: Memory block size: 128MB
[ 0.305586] evm: security.selinux
[ 0.305587] evm: security.SMACK64
[ 0.305588] evm: security.SMACK64EXEC
[ 0.305589] evm: security.SMACK64TRANSMUTE
[ 0.305590] evm: security.SMACK64MMAP
[ 0.305591] evm: security.ima
[ 0.305592] evm: security.capability
[ 0.305616] PM: Registering ACPI NVS region [mem 0xdaeef000-0xdaf9efff] (720896 bytes)
[ 0.305616] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.305616] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.305616] pinctrl core: initialized pinctrl subsystem
[ 0.305616] RTC time: 10:30:58, date: 11/08/17
[ 0.305616] NET: Registered protocol family 16
[ 0.305616] cpuidle: using governor ladder
[ 0.305616] cpuidle: using governor menu
[ 0.305616] ACPI: bus type PCI registered
[ 0.305616] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.305616] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.305616] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.305616] PCI: Using configuration type 1 for base access
[ 0.305616] core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
[ 0.309406] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.309406] ACPI: Added _OSI(Module Device)
[ 0.309406] ACPI: Added _OSI(Processor Device)
[ 0.309406] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.309406] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.309406] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.315360] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[ 0.316548] ACPI: Dynamic OEM Table Load:
[ 0.316561] ACPI: SSDT 0xFFFF8AE650A9A000 000784 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.316701] ACPI: Dynamic OEM Table Load:
[ 0.316701] ACPI: SSDT 0xFFFF8AE6509FF800 000303 (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.316707] ACPI: Dynamic OEM Table Load:
[ 0.316707] ACPI: SSDT 0xFFFF8AE650A4F800 000119 (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.316966] ACPI: EC: EC started
[ 0.316967] ACPI: EC: interrupt blocked
[ 0.320581] ACPI: \_SB_.PCI0.LPCB.H_EC: Used as first EC
[ 0.320584] ACPI: \_SB_.PCI0.LPCB.H_EC: GPE=0x17, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.320586] ACPI: \_SB_.PCI0.LPCB.H_EC: Used as boot DSDT EC to handle transactions
[ 0.320587] ACPI: Interpreter enabled
[ 0.320625] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.320627] ACPI: Using IOAPIC for interrupt routing
[ 0.320665] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.321027] ACPI: Enabled 8 GPEs in block 00 to 3F
[ 0.331651] ACPI: Power Resource [FN00] (off)
[ 0.331781] ACPI: Power Resource [FN01] (off)
[ 0.331904] ACPI: Power Resource [FN02] (off)
[ 0.332030] ACPI: Power Resource [FN03] (off)
[ 0.332155] ACPI: Power Resource [FN04] (off)
[ 0.332967] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.332974] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.333172] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[ 0.333785] PCI host bridge to bus 0000:00
[ 0.333789] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.333791] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.333793] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.333795] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfeafffff window]
[ 0.333797] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.333808] pci 0000:00:00.0: [8086:0104] type 00 class 0x060000
[ 0.333951] pci 0000:00:02.0: [8086:0116] type 00 class 0x030000
[ 0.333967] pci 0000:00:02.0: reg 0x10: [mem 0xf0000000-0xf03fffff 64bit]
[ 0.333975] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.333981] pci 0000:00:02.0: reg 0x20: [io 0x3000-0x303f]
[ 0.334147] pci 0000:00:14.0: [8086:1e31] type 00 class 0x0c0330
[ 0.334186] pci 0000:00:14.0: reg 0x10: [mem 0xf0600000-0xf060ffff 64bit]
[ 0.334285] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.334400] pci 0000:00:16.0: [8086:1e3a] type 00 class 0x078000
[ 0.334439] pci 0000:00:16.0: reg 0x10: [mem 0xf0615000-0xf061500f 64bit]
[ 0.334538] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.334665] pci 0000:00:1a.0: [8086:1e2d] type 00 class 0x0c0320
[ 0.334695] pci 0000:00:1a.0: reg 0x10: [mem 0xf061a000-0xf061a3ff]
[ 0.334808] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.334923] pci 0000:00:1b.0: [8086:1e20] type 00 class 0x040300
[ 0.334957] pci 0000:00:1b.0: reg 0x10: [mem 0xf0610000-0xf0613fff 64bit]
[ 0.335068] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.335194] pci 0000:00:1c.0: [8086:1e10] type 01 class 0x060400
[ 0.335315] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.335441] pci 0000:00:1c.3: [8086:1e16] type 01 class 0x060400
[ 0.335557] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.335687] pci 0000:00:1d.0: [8086:1e26] type 00 class 0x0c0320
[ 0.335719] pci 0000:00:1d.0: reg 0x10: [mem 0xf0619000-0xf06193ff]
[ 0.335830] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.335944] pci 0000:00:1f.0: [8086:1e59] type 00 class 0x060100
[ 0.336198] pci 0000:00:1f.2: [8086:1e03] type 00 class 0x010601
[ 0.336229] pci 0000:00:1f.2: reg 0x10: [io 0x3088-0x308f]
[ 0.336242] pci 0000:00:1f.2: reg 0x14: [io 0x3094-0x3097]
[ 0.336253] pci 0000:00:1f.2: reg 0x18: [io 0x3080-0x3087]
[ 0.336265] pci 0000:00:1f.2: reg 0x1c: [io 0x3090-0x3093]
[ 0.336278] pci 0000:00:1f.2: reg 0x20: [io 0x3060-0x307f]
[ 0.336287] pci 0000:00:1f.2: reg 0x24: [mem 0xf0618000-0xf06187ff]
[ 0.336352] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.336459] pci 0000:00:1f.3: [8086:1e22] type 00 class 0x0c0500
[ 0.336491] pci 0000:00:1f.3: reg 0x10: [mem 0xf0614000-0xf06140ff 64bit]
[ 0.336523] pci 0000:00:1f.3: reg 0x20: [io 0xefa0-0xefbf]
[ 0.336758] pci 0000:01:00.0: [8086:088e] type 00 class 0x028000
[ 0.336834] pci 0000:01:00.0: reg 0x10: [mem 0xf0500000-0xf0501fff 64bit]
[ 0.337103] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.348056] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.348076] pci 0000:00:1c.0: bridge window [mem 0xf0500000-0xf05fffff]
[ 0.348237] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000
[ 0.348372] pci 0000:02:00.0: reg 0x10: [io 0x2000-0x20ff]
[ 0.348502] pci 0000:02:00.0: reg 0x18: [mem 0xf0404000-0xf0404fff 64bit pref]
[ 0.348582] pci 0000:02:00.0: reg 0x20: [mem 0xf0400000-0xf0403fff 64bit pref]
[ 0.349010] pci 0000:02:00.0: supports D1 D2
[ 0.349012] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.360100] pci 0000:00:1c.3: PCI bridge to [bus 02]
[ 0.360105] pci 0000:00:1c.3: bridge window [io 0x2000-0x2fff]
[ 0.360117] pci 0000:00:1c.3: bridge window [mem 0xf0400000-0xf04fffff 64bit pref]
[ 0.361193] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.361273] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.361351] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
[ 0.361428] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.361504] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.361581] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
[ 0.361657] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.361733] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.362591] ACPI: EC: interrupt unblocked
[ 0.362600] ACPI: EC: event unblocked
[ 0.362608] ACPI: \_SB_.PCI0.LPCB.H_EC: GPE=0x17, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.362610] ACPI: \_SB_.PCI0.LPCB.H_EC: Used as boot DSDT EC to handle transactions and events
[ 0.362707] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.362707] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.362707] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.362707] vgaarb: loaded
[ 0.362707] SCSI subsystem initialized
[ 0.362707] libata version 3.00 loaded.
[ 0.362707] ACPI: bus type USB registered
[ 0.362707] usbcore: registered new interface driver usbfs
[ 0.362707] usbcore: registered new interface driver hub
[ 0.362707] usbcore: registered new device driver usb
[ 0.362707] EDAC MC: Ver: 3.0.0
[ 0.362707] PCI: Using ACPI for IRQ routing
[ 0.365422] PCI: pci_cache_line_size set to 64 bytes
[ 0.365487] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.365489] e820: reserve RAM buffer [mem 0xc42aa000-0xc7ffffff]
[ 0.365490] e820: reserve RAM buffer [mem 0xd33ef000-0xd3ffffff]
[ 0.365492] e820: reserve RAM buffer [mem 0xdb000000-0xdbffffff]
[ 0.365493] e820: reserve RAM buffer [mem 0x31f600000-0x31fffffff]
[ 0.365630] NetLabel: Initializing
[ 0.365631] NetLabel: domain hash size = 128
[ 0.365632] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.365657] NetLabel: unlabeled traffic allowed by default
[ 0.365679] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.365679] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.366115] clocksource: Switched to clocksource hpet
[ 0.380567] VFS: Disk quotas dquot_6.6.0
[ 0.380601] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.380739] AppArmor: AppArmor Filesystem Enabled
[ 0.380781] pnp: PnP ACPI init
[ 0.381293] system 00:00: [io 0x0680-0x069f] has been reserved
[ 0.381296] system 00:00: [io 0x1000-0x100f] has been reserved
[ 0.381299] system 00:00: [io 0x5000-0x5003] has been reserved
[ 0.381301] system 00:00: [io 0xffff] has been reserved
[ 0.381303] system 00:00: [io 0x0400-0x0453] has been reserved
[ 0.381305] system 00:00: [io 0x0458-0x047f] has been reserved
[ 0.381307] system 00:00: [io 0x0500-0x057f] has been reserved
[ 0.381309] system 00:00: [io 0x0a00-0x0a0f] has been reserved
[ 0.381312] system 00:00: [io 0x164e-0x164f] has been reserved
[ 0.381314] system 00:00: [io 0x5000-0x500f] could not be reserved
[ 0.381322] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.381358] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.381435] system 00:02: [io 0x0454-0x0457] has been reserved
[ 0.381441] system 00:02: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.381482] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.381538] pnp 00:04: Plug and Play ACPI device, IDs ETD0b00 SYN0002 PNP0f13 (active)
[ 0.381749] system 00:05: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.381751] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.381754] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.381756] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.381758] system 00:05: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.381760] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.381762] system 00:05: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.381765] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.381767] system 00:05: [mem 0xff000000-0xffffffff] could not be reserved
[ 0.381770] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.381772] system 00:05: [mem 0xfffff000-0xffffffff] has been reserved
[ 0.381778] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.382319] pnp: PnP ACPI: found 6 devices
[ 0.389878] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.389912] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.389921] pci 0000:00:1c.0: bridge window [mem 0xf0500000-0xf05fffff]
[ 0.389935] pci 0000:00:1c.3: PCI bridge to [bus 02]
[ 0.389939] pci 0000:00:1c.3: bridge window [io 0x2000-0x2fff]
[ 0.389949] pci 0000:00:1c.3: bridge window [mem 0xf0400000-0xf04fffff 64bit pref]
[ 0.389961] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.389963] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.389965] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.389967] pci_bus 0000:00: resource 7 [mem 0xdfa00000-0xfeafffff window]
[ 0.389969] pci_bus 0000:01: resource 1 [mem 0xf0500000-0xf05fffff]
[ 0.389971] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 0.389973] pci_bus 0000:02: resource 2 [mem 0xf0400000-0xf04fffff 64bit pref]
[ 0.390105] NET: Registered protocol family 2
[ 0.390408] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.390760] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.390958] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.391028] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.391104] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.391232] NET: Registered protocol family 1
[ 0.391253] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.392051] PCI: CLS 64 bytes, default 64
[ 0.392120] Unpacking initramfs...
[ 1.679547] Freeing initrd memory: 51000K
[ 1.679578] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.679582] software IO TLB [mem 0xcf3ef000-0xd33ef000] (64MB) mapped at [ffff8ae40f3ef000-ffff8ae4133eefff]
[ 1.679879] Scanning for low memory corruption every 60 seconds
[ 1.680369] audit: initializing netlink subsys (disabled)
[ 1.680435] audit: type=2000 audit(1510137059.676:1): state=initialized audit_enabled=0 res=1
[ 1.680959] Initialise system trusted keyrings
[ 1.680971] Key type blacklist registered
[ 1.681028] workingset: timestamp_bits=36 max_order=22 bucket_order=0
[ 1.682739] zbud: loaded
[ 1.683328] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.683540] fuse init (API version 7.26)
[ 1.685600] Key type asymmetric registered
[ 1.685602] Asymmetric key parser 'x509' registered
[ 1.685657] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 1.685704] io scheduler noop registered
[ 1.685705] io scheduler deadline registered
[ 1.685775] io scheduler cfq registered (default)
[ 1.686411] vesafb: mode is 1366x768x32, linelength=5504, pages=0
[ 1.686412] vesafb: scrolling: redraw
[ 1.686414] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.686428] vesafb: framebuffer at 0xe0000000, mapped to 0xffffb4d642000000, using 4160k, total 4160k
[ 1.797243] Console: switching to colour frame buffer device 170x48
[ 1.907641] fb0: VESA VGA frame buffer device
[ 1.907683] intel_idle: MWAIT substates: 0x21120
[ 1.907685] intel_idle: v0.4.1 model 0x2A
[ 1.907895] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 1.908185] ACPI: AC Adapter [ADP1] (on-line)
[ 1.908303] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 1.908335] ACPI: Lid Switch [LID0]
[ 1.908385] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 1.908422] ACPI: Power Button [PWRB]
[ 1.908474] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 1.908502] ACPI: Power Button [PWRF]
[ 1.909882] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[ 1.910216] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.910218] ACPI: Thermal Zone [TZ00] (29 C)
[ 1.910559] thermal LNXTHERM:01: registered as thermal_zone1
[ 1.910561] ACPI: Thermal Zone [TZ01] (30 C)
[ 1.910718] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 1.910893] ACPI: Battery Slot [BAT1] (battery absent)
[ 1.912887] Linux agpgart interface v0.103
[ 1.915159] loop: module loaded
[ 1.915390] libphy: Fixed MDIO Bus: probed
[ 1.915392] tun: Universal TUN/TAP device driver, 1.6
[ 1.915443] PPP generic driver version 2.4.2
[ 1.915505] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.915509] ehci-pci: EHCI PCI platform driver
[ 1.915682] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 1.915690] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.915710] ehci-pci 0000:00:1a.0: debug port 2
[ 1.919620] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 1.919637] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf061a000
[ 1.932120] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 1.932207] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.932210] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.932212] usb usb1: Product: EHCI Host Controller
[ 1.932214] usb usb1: Manufacturer: Linux 4.14.0-041400rc8-generic ehci_hcd
[ 1.932215] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.932428] hub 1-0:1.0: USB hub found
[ 1.932436] hub 1-0:1.0: 3 ports detected
[ 1.932799] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 1.932807] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.932823] ehci-pci 0000:00:1d.0: debug port 2
[ 1.936740] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 1.936757] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf0619000
[ 1.952119] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 1.952219] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.952222] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.952224] usb usb2: Product: EHCI Host Controller
[ 1.952226] usb usb2: Manufacturer: Linux 4.14.0-041400rc8-generic ehci_hcd
[ 1.952228] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.952432] hub 2-0:1.0: USB hub found
[ 1.952441] hub 2-0:1.0: 3 ports detected
[ 1.952617] ehci-platform: EHCI generic platform driver
[ 1.952642] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.952646] ohci-pci: OHCI PCI platform driver
[ 1.952658] ohci-platform: OHCI generic platform driver
[ 1.952667] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.952897] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.952904] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 1.954002] xhci_hcd 0000:00:14.0: hcc params 0x20007181 hci version 0x100 quirks 0x0000b930
[ 1.954010] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 1.954128] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.954130] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.954132] usb usb3: Product: xHCI Host Controller
[ 1.954133] usb usb3: Manufacturer: Linux 4.14.0-041400rc8-generic xhci-hcd
[ 1.954135] usb usb3: SerialNumber: 0000:00:14.0
[ 1.954276] hub 3-0:1.0: USB hub found
[ 1.954288] hub 3-0:1.0: 4 ports detected
[ 1.954737] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.954744] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[ 1.954787] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.954789] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.954791] usb usb4: Product: xHCI Host Controller
[ 1.954793] usb usb4: Manufacturer: Linux 4.14.0-041400rc8-generic xhci-hcd
[ 1.954794] usb usb4: SerialNumber: 0000:00:14.0
[ 1.954933] hub 4-0:1.0: USB hub found
[ 1.954945] hub 4-0:1.0: 4 ports detected
[ 1.955427] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:EPAD] at 0x60,0x64 irq 1,12
[ 1.961383] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.961389] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.961576] mousedev: PS/2 mouse device common for all mice
[ 1.961984] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[ 1.962015] rtc_cmos 00:01: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.962025] i2c /dev entries driver
[ 1.962097] device-mapper: uevent: version 1.0.3
[ 1.962191] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: [email protected]
[ 1.962199] intel_pstate: Intel P-state driver initializing
[ 1.962490] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.963094] NET: Registered protocol family 10
[ 1.968539] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.969003] Segment Routing with IPv6
[ 1.969033] NET: Registered protocol family 17
[ 1.969095] Key type dns_resolver registered
[ 1.969511] RAS: Correctable Errors collector initialized.
[ 1.969551] microcode: sig=0x206a7, pf=0x10, revision=0x29
[ 1.969636] microcode: Microcode Update Driver: v2.2.
[ 1.969650] sched_clock: Marking stable (1969629319, 0)->(1974532808, -4903489)
[ 1.969957] registered taskstats version 1
[ 1.969968] Loading compiled-in X.509 certificates
[ 1.973917] Loaded X.509 cert 'Build time autogenerated kernel key: 32ee9ae27249a1f608beaa34bc3ee875bcba84a7'
[ 1.973949] zswap: loaded using pool lzo/zbud
[ 1.978668] Key type big_key registered
[ 1.978673] Key type trusted registered
[ 1.981042] Key type encrypted registered
[ 1.981047] AppArmor: AppArmor sha1 policy hashing enabled
[ 1.981051] ima: No TPM chip found, activating TPM-bypass! (rc=-19)
[ 1.981078] evm: HMAC attrs: 0x1
[ 1.981363] Magic number: 9:169:527
[ 1.981531] rtc_cmos 00:01: setting system clock to 2017-11-08 10:31:00 UTC (1510137060)
[ 1.981636] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.981637] EDD information not available.
[ 1.986015] Freeing unused kernel memory: 2320K
[ 1.986018] Write protecting the kernel read-only data: 14336k
[ 1.986540] Freeing unused kernel memory: 772K
[ 1.986744] Freeing unused kernel memory: 44K
[ 1.999072] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 2.156339] ahci 0000:00:1f.2: version 3.0
[ 2.156683] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3 impl SATA mode
[ 2.156689] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst
[ 2.162029] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.162046] r8169 0000:02:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 2.162836] r8169 0000:02:00.0 eth0: RTL8168evl/8111evl at 0xffffb4d641915000, e8:03:9a:0f:c4:4f, XID 0c900800 IRQ 26
[ 2.162841] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 2.171299] r8169 0000:02:00.0 enp2s0: renamed from eth0
[ 2.172113] scsi host0: ahci
[ 2.172728] scsi host1: ahci
[ 2.172898] scsi host2: ahci
[ 2.173078] scsi host3: ahci
[ 2.173239] scsi host4: ahci
[ 2.173396] scsi host5: ahci
[ 2.173489] ata1: SATA max UDMA/133 abar m2048@0xf0618000 port 0xf0618100 irq 25
[ 2.173494] ata2: SATA max UDMA/133 abar m2048@0xf0618000 port 0xf0618180 irq 25
[ 2.173496] ata3: DUMMY
[ 2.173497] ata4: DUMMY
[ 2.173499] ata5: DUMMY
[ 2.173501] ata6: DUMMY
[ 2.219435] [drm] Memory usable by graphics device = 2048M
[ 2.219439] checking generic (e0000000 410000) vs hw (e0000000 10000000)
[ 2.219440] fb: switching to inteldrmfb from VESA VGA
[ 2.219543] Console: switching to colour dummy device 80x25
[ 2.219681] [drm] Replacing VGA console driver
[ 2.225642] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.225645] [drm] Driver supports precise vblank timestamp query.
[ 2.229260] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 2.239991] [drm] Initialized i915 1.6.0 20170818 for 0000:00:02.0 on minor 0
[ 2.240947] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 2.241305] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
[ 2.274484] fbcon: inteldrmfb (fb0) is primary device
[ 2.276129] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 2.288134] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 2.288164] usb 3-1: new low-speed USB device number 2 using xhci_hcd
[ 2.432783] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 2.432785] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.433187] hub 1-1:1.0: USB hub found
[ 2.433372] hub 1-1:1.0: 6 ports detected
[ 2.440310] usb 3-1: New USB device found, idVendor=046d, idProduct=c077
[ 2.440313] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.440315] usb 3-1: Product: USB Optical Mouse
[ 2.440316] usb 3-1: Manufacturer: Logitech
[ 2.444483] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 2.444486] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.444774] hub 2-1:1.0: USB hub found
[ 2.444843] hub 2-1:1.0: 6 ports detected
[ 2.446489] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.451144] usbcore: registered new interface driver usbhid
[ 2.451145] usbhid: USB HID core driver
[ 2.453709] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1:1.0/0003:046D:C077.0001/input/input7
[ 2.453939] hid-generic 0003:046D:C077.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-1/input0
[ 2.487386] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.487411] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.488011] ata2.00: ATA-9: SanDisk SSD i100 24GB, 11.50.04, max UDMA/133
[ 2.488024] ata2.00: 46905264 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 2.488395] ata2.00: configured for UDMA/133
[ 2.567808] ata1.00: ATA-8: Hitachi HTS545050A7E380, GG2OA6C0, max UDMA/133
[ 2.567811] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 2.569097] ata1.00: configured for UDMA/133
[ 2.569397] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54505 A6C0 PQ: 0 ANSI: 5
[ 2.569789] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 2.569793] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 2.569799] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.569810] sd 0:0:0:0: [sda] Write Protect is off
[ 2.569813] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.569844] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.570130] scsi 1:0:0:0: Direct-Access ATA SanDisk SSD i100 0.04 PQ: 0 ANSI: 5
[ 2.570441] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 2.570502] sd 1:0:0:0: [sdb] 46905264 512-byte logical blocks: (24.0 GB/22.4 GiB)
[ 2.570523] sd 1:0:0:0: [sdb] Write Protect is off
[ 2.570527] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.570578] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.571364] sdb: sdb1
[ 2.571895] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 2.618930] sda: sda2 sda4 < sda5 sda6 >
[ 2.619525] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.684158] tsc: Refined TSC clocksource calibration: 1496.600 MHz
[ 2.684174] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x159296d3708, max_idle_ns: 440795218047 ns
[ 2.720165] usb 1-1.4: new high-speed USB device number 3 using ehci-pci
[ 2.732172] usb 2-1.5: new full-speed USB device number 3 using ehci-pci
[ 2.845123] usb 2-1.5: New USB device found, idVendor=8087, idProduct=07da
[ 2.845126] usb 2-1.5: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.948673] usb 1-1.4: New USB device found, idVendor=2232, idProduct=1035
[ 2.948676] usb 1-1.4: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 2.948678] usb 1-1.4: Product: WebCam SC-13HDL12131N
[ 2.948679] usb 1-1.4: Manufacturer: Generic
[ 2.948681] usb 1-1.4: SerialNumber: 200901010001
[ 3.021746] Console: switching to colour frame buffer device 170x48
[ 3.042278] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 3.049186] psmouse serio1: elantech: assuming hardware version 3 (with firmware version 0x450f00)
[ 3.063898] psmouse serio1: elantech: Synaptics capabilities query result 0x08, 0x17, 0x0c.
[ 3.078605] psmouse serio1: elantech: Elan sample query result 03, 3f, 86
[ 3.154246] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input5
[ 3.708431] clocksource: Switched to clocksource tsc
[ 3.852071] raid6: sse2x1 gen() 4548 MB/s
[ 3.920072] raid6: sse2x1 xor() 3134 MB/s
[ 3.988076] raid6: sse2x2 gen() 5350 MB/s
[ 4.056072] raid6: sse2x2 xor() 3614 MB/s
[ 4.124072] raid6: sse2x4 gen() 6361 MB/s
[ 4.192065] raid6: sse2x4 xor() 4294 MB/s
[ 4.192068] raid6: using algorithm sse2x4 gen() 6361 MB/s
[ 4.192069] raid6: .... xor() 4294 MB/s, rmw enabled
[ 4.192071] raid6: using ssse3x2 recovery algorithm
[ 4.197975] xor: automatically using best checksumming function avx
[ 4.228187] Btrfs loaded, crc32c=crc32c-intel
[ 4.586509] BTRFS: device fsid 707d0f89-4b1d-4432-9d50-6058dc4c1ee9 devid 1 transid 26380 /dev/sdb1
[ 4.619018] BTRFS info (device sdb1): disk space caching is enabled
[ 4.619021] BTRFS info (device sdb1): has skinny extents
[ 4.632489] BTRFS info (device sdb1): enabling ssd optimizations
[ 4.847235] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.853094] systemd[1]: systemd 234 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN default-hierarchy=hybrid)
[ 4.964137] systemd[1]: Detected architecture x86-64.
[ 4.964747] systemd[1]: Set hostname to <caravena-530U3C-530U4C>.
[ 5.060997] systemd[1]: Listening on Journal Audit Socket.
[ 5.061118] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 5.061162] systemd[1]: Listening on Syslog Socket.
[ 5.061202] systemd[1]: Listening on Journal Socket (/dev/log).
[ 5.061386] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 5.061460] systemd[1]: Listening on Journal Socket.
[ 5.061491] systemd[1]: Reached target Remote File Systems.
[ 5.110994] lp: driver loaded but no devices found
[ 5.116368] ppdev: user-space parallel port driver
[ 5.213621] BTRFS info (device sdb1): disk space caching is enabled
[ 5.249479] swapon: swapfile has holes
[ 5.249796] systemd-journald[288]: Received request to flush runtime journal from PID 1
[ 5.485341] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 5.501419] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20170728/utaddress-247)
[ 5.501432] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.501793] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20170728/utaddress-247)
[ 5.501805] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.501807] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20170728/utaddress-247)
[ 5.501815] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.501817] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20170728/utaddress-247)
[ 5.501824] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.501825] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 5.567365] Intel(R) Wireless WiFi driver for Linux
[ 5.567368] Copyright(c) 2003- 2015 Intel Corporation
[ 5.567590] iwlwifi 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 5.572352] media: Linux media interface: v0.10
[ 5.576896] iwlwifi 0000:01:00.0: loaded firmware version 18.168.6.1 op_mode iwldvm
[ 5.597443] Linux video capture interface: v2.00
[ 5.626342] Bluetooth: Core ver 2.22
[ 5.626367] NET: Registered protocol family 31
[ 5.626369] Bluetooth: HCI device and connection manager initialized
[ 5.626375] Bluetooth: HCI socket layer initialized
[ 5.626379] Bluetooth: L2CAP socket layer initialized
[ 5.626389] Bluetooth: SCO socket layer initialized
[ 5.635661] iwlwifi 0000:01:00.0: CONFIG_IWLWIFI_DEBUG disabled
[ 5.635666] iwlwifi 0000:01:00.0: CONFIG_IWLWIFI_DEBUGFS enabled
[ 5.635668] iwlwifi 0000:01:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled
[ 5.635672] iwlwifi 0000:01:00.0: Detected Intel(R) Centrino(R) Advanced-N 6235 AGN, REV=0xB0
[ 5.696437] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 5.702800] usbcore: registered new interface driver btusb
[ 5.725972] uvcvideo: Found UVC 1.00 device WebCam SC-13HDL12131N (2232:1035)
[ 5.733075] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms ovfl timer
[ 5.733078] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[ 5.733080] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 5.733081] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[ 5.747548] uvcvideo 1-1.4:1.0: Entity type for entity Extension 4 was not initialized!
[ 5.747554] uvcvideo 1-1.4:1.0: Entity type for entity Processing 2 was not initialized!
[ 5.747558] uvcvideo 1-1.4:1.0: Entity type for entity Camera 1 was not initialized!
[ 5.747845] input: WebCam SC-13HDL12131N: WebCam S as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input8
[ 5.747997] usbcore: registered new interface driver uvcvideo
[ 5.747999] USB Video Class driver (1.1.1)
[ 5.852477] samsung_laptop: detected SABI interface: SwSmi@
[ 5.884000] intel_rapl: Found RAPL domain package
[ 5.884003] intel_rapl: Found RAPL domain core
[ 5.884005] intel_rapl: Found RAPL domain uncore
[ 5.884014] intel_rapl: RAPL package 0 domain package locked by BIOS
[ 6.029303] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[ 6.034334] iwlwifi 0000:01:00.0 wlp1s0: renamed from wlan0
[ 6.043201] swapon: swapfile has holes
[ 6.078855] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC269VC: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 6.078862] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 6.078866] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x15/0x0/0x0/0x0/0x0)
[ 6.078869] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
[ 6.078871] snd_hda_codec_realtek hdaudioC0D0: inputs:
[ 6.078875] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x19
[ 6.078879] snd_hda_codec_realtek hdaudioC0D0: Mic=0x18
[ 6.100495] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 6.100627] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 6.100742] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 6.152884] random: crng init done
[ 7.664633] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[ 7.779405] audit: type=1400 audit(1510137066.290:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=637 comm="apparmor_parser"
[ 7.779719] audit: type=1400 audit(1510137066.290:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=636 comm="apparmor_parser"
[ 7.782339] audit: type=1400 audit(1510137066.294:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=639 comm="apparmor_parser"
[ 7.788582] audit: type=1400 audit(1510137066.302:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=633 comm="apparmor_parser"
[ 7.788591] audit: type=1400 audit(1510137066.302:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=633 comm="apparmor_parser"
[ 7.788596] audit: type=1400 audit(1510137066.302:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=633 comm="apparmor_parser"
[ 7.788601] audit: type=1400 audit(1510137066.302:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=633 comm="apparmor_parser"
[ 7.790570] audit: type=1400 audit(1510137066.302:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine" pid=640 comm="apparmor_parser"
[ 7.790579] audit: type=1400 audit(1510137066.302:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=640 comm="apparmor_parser"
[ 7.794709] audit: type=1400 audit(1510137066.306:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-soffice" pid=638 comm="apparmor_parser"
[ 8.068155] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 8.068158] Bluetooth: BNEP filters: protocol multicast
[ 8.068164] Bluetooth: BNEP socket layer initialized
[ 8.502127] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready
[ 8.626835] r8169 0000:02:00.0 enp2s0: link down
[ 8.627425] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready
[ 8.638445] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 8.652601] iwlwifi 0000:01:00.0: Radio type=0x2-0x1-0x0
[ 8.957648] iwlwifi 0000:01:00.0: Radio type=0x2-0x1-0x0
[ 9.041939] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 9.155022] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 15.233233] wlp1s0: authenticate with 4c:fa:ca:42:1f:d4
[ 15.236540] wlp1s0: send auth to 4c:fa:ca:42:1f:d4 (try 1/3)
[ 15.325371] wlp1s0: authenticated
[ 15.328122] wlp1s0: associate with 4c:fa:ca:42:1f:d4 (try 1/3)
[ 15.339147] wlp1s0: RX AssocResp from 4c:fa:ca:42:1f:d4 (capab=0x1411 status=0 aid=2)
[ 15.358435] wlp1s0: associated
[ 15.358602] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready
[ 15.426884] wlp1s0: Limiting TX power to 20 (23 - 3) dBm as advertised by 4c:fa:ca:42:1f:d4
[ 22.943521] Bluetooth: RFCOMM TTY layer initialized
[ 22.943530] Bluetooth: RFCOMM socket layer initialized
[ 22.943539] Bluetooth: RFCOMM ver 1.11
[ 26.533628] rfkill: input handler disabled
[ 7752.948217] usb 3-4: new full-speed USB device number 3 using xhci_hcd
[ 7753.331300] usb 3-4: New USB device found, idVendor=047f, idProduct=c022
[ 7753.331307] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7753.331311] usb 3-4: Product: Plantronics C310
[ 7753.331315] usb 3-4: Manufacturer: Plantronics
[ 7753.331318] usb 3-4: SerialNumber: 32A26B7A3023464D9CF5091CF1780483
[ 7753.594811] input: Plantronics Plantronics C310 as /devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.3/0003:047F:C022.0002/input/input12
[ 7753.647949] usb 3-4: Warning! Unlikely big volume range (=10361), cval->res is probably wrong.
[ 7753.647953] usb 3-4: [11] FU [Sidetone Playback Volume] ch = 1, val = 0/10361/1
[ 7753.651629] usbcore: registered new interface driver snd-usb-audio
[ 7753.657302] plantronics 0003:047F:C022.0002: input,hiddev0,hidraw1: USB HID v1.11 Device [Plantronics Plantronics C310] on usb-0000:00:14.0-4/input3
[ 8223.624532] usb 4-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 8223.645137] usb 4-2: New USB device found, idVendor=2537, idProduct=1068
[ 8223.645144] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8223.645148] usb 4-2: Product: NS1068
[ 8223.645152] usb 4-2: Manufacturer: Norelsys
[ 8223.645155] usb 4-2: SerialNumber: 0123456789ABCDE
[ 8223.670968] usbcore: registered new interface driver usb-storage
[ 8223.675930] scsi host6: uas
[ 8223.676154] usbcore: registered new interface driver uas
[ 8226.032839] scsi 6:0:0:0: Direct-Access ATA Hitachi HTS54252 C3BP PQ: 0 ANSI: 6
[ 8226.037293] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 8226.039981] sd 6:0:0:0: [sdc] 488397168 512-byte logical blocks: (250 GB/233 GiB)
[ 8226.040107] sd 6:0:0:0: [sdc] Write Protect is off
[ 8226.040112] sd 6:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 8226.040303] sd 6:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 8226.072275] sdc: sdc1 sdc2 sdc3
[ 8226.085324] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 8517.739152] xhci_hcd 0000:00:14.0: Cannot set link state.
[ 8517.739203] usb usb4-port2: cannot disable (err = -32)
[ 8517.739216] usb 4-2: USB disconnect, device number 2
