On Mon, Sep 12, 2016 at 12:06:10PM +0200, Fabien Lahoudere wrote: > > > On 12/09/16 11:46, Peter Chen wrote: > >On Mon, Sep 12, 2016 at 11:13:01AM +0200, Fabien Lahoudere wrote: > >>Hi, > >> > >>>Yes, please send the patch and tell me which dts and ULPI code you are > >>>using. We need to understand why the system is hang when configure the > >>>PHY mode at portsc for your case, afaik, the PHY mode needs to be > >>>configured as ULPI mode before using ULPI view port to access ULPI PHY. > >> > >>Patch have been sent "usb: imx53 - Allow to configure ULPI mode for usb host > >>2 and 3", in reply to this thread. > >> > >>> > >>>Besides, do you enable this ULPI PHY at u-boot? > >>> > >> > >>Yes, I configure imx53 in linux kernel in order to use ULPI mode. I remind > >>you that the patch works fine with my device. > >> > > > >I know you are using it at kernel. I just want to know if you enable it > >at bootloader, besides, I need to know more about your platform since > >the system hang usually dues to without PHY clock, so would you send > >platform stuffs like dts (which dts), etc? > > > > No USB are not used in uboot. > > This is our device tree imx-ppd.dts:
I may know the reason why you meet hang at current flow, you are using generic phy driver, and the PHY clock is enabled at phy_init which is called later than setting portsc.pts. The current flow to enable ULPI phy is like below: 1. Enable ULPI and choose its clock select at usbmisc, which you have already done. 2. Enable the input clock for ULPI 3. set portsc.pts You may need to have a ULPI PHY driver which do some power sequence (clock, regulator, etc) before setting portsc.pts and visit ULPI register. I am also a little confused how Stephen Boyd's ULPI driver for qualcomm platform, I will cc on discussion. Peter > > /* > * Copyright 2014 General Electric Company > * > * The code contained herein is licensed under the GNU General Public > * License. You may obtain a copy of the GNU General Public License > * Version 2 or later at the following locations: > * > * http://www.opensource.org/licenses/gpl-license.html > * http://www.gnu.org/copyleft/gpl.html > */ > > /dts-v1/; > > #include "imx53.dtsi" > > / { > model = "Freescale i.MX53 CPUV0 PPD rev6"; > compatible = "fsl,imx53-cpuvo", "fsl,imx53"; > > aliases { > spi0 = &cspi; > spi1 = &ecspi1; > spi2 = &ecspi2; > }; > > chosen { > stdout-path = "&uart1:115200n8"; > }; > > memory { > reg = <0x70000000 0x20000000>, > <0xb0000000 0x20000000>; > }; > > cko2_11M: sgtl_clock_cko2 { > compatible = "fixed-clock"; > #clock-cells = <0>; > clock-frequency = <11289600>; > }; > > sgtlsound: sound { > compatible = "fsl,imx53-cpuvo-sgtl5000", > "fsl,imx-audio-sgtl5000"; > model = "imx53-cpuvo-sgtl5000"; > ssi-controller = <&ssi2>; > audio-codec = <&sgtl5000>; > audio-routing = > "MIC_IN", "Mic Jack", > "Mic Jack", "Mic Bias", > "Headphone Jack", "HP_OUT"; > mux-int-port = <2>; > mux-ext-port = <6>; > status = "okay"; > }; > > reg_sgtl5k: regulator-sgtl5k { > compatible = "regulator-fixed"; > regulator-name = "regulator-sgtl5k"; > regulator-min-microvolt = <3300000>; > regulator-max-microvolt = <3300000>; > regulator-always-on; > }; > > reg_usb_otg_vbus: regulator-usb-otg-vbus { > compatible = "regulator-fixed"; > regulator-name = "usbotg_vbus"; > regulator-min-microvolt = <5000000>; > regulator-max-microvolt = <5000000>; > pinctrl-0 = <&pinctrl_usb_otg_vbus>; > gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; > enable-active-high; > regulator-always-on; > }; > > reg_usb_vbus: regulator-usb-vbus { > compatible = "regulator-fixed"; > regulator-name = "usbh1_vbus"; > regulator-min-microvolt = <5000000>; > regulator-max-microvolt = <5000000>; > pinctrl-0 = <&pinctrl_usbh1_vbus>; > gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; > enable-active-high; > regulator-always-on; > }; > > reg_usbh2_vbus: regulator-usbh2-vbus { > compatible = "regulator-fixed"; > regulator-name = "usbh2_vbus"; > regulator-min-microvolt = <5000000>; > regulator-max-microvolt = <5000000>; > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_usbh2_vbus>; > gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; > enable-active-high; > regulator-boot-on; > }; > > reg_usbh3_vbus: regulator-usbh3-vbus { > compatible = "regulator-fixed"; > regulator-name = "usbh3_vbus"; > regulator-min-microvolt = <5000000>; > regulator-max-microvolt = <5000000>; > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_usbh3_vbus>; > gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; > enable-active-high; > regulator-boot-on; > }; > > backlight: pwm-bl@2 { > compatible = "pwm-backlight"; > pwms = <&pwm2 0 50000>; > brightness-levels = <0 2 5 7 10 12 15 17 20 22 25 28 30 33 35 \ > 38 40 43 45 48 51 53 56 58 61 63 66 68 71 \ > 73 76 79 81 84 86 89 91 94 96 99 102 104 \ > 107 109 112 114 117 119 122 124 127 130 \ > 132 135 137 140 142 145 147 150 153 155 \ > 158 160 163 165 168 170 173 175 178 181 \ > 183 186 188 191 193 196 198 201 204 206 \ > 209 211 214 216 219 221 224 226 229 232 \ > 234 237 239 242 244 247 249 252 255>; > default-brightness-level = <0>; > enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; > }; > > leds { > compatible = "pwm-leds"; > alarm-brightness { > pwms = <&pwm1 0 100000>; > max-brightness = <255>; > }; > }; > > gpio-poweroff { > compatible = "gpio-poweroff"; > gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>; > }; > > power-gpio-keys { > compatible = "gpio-keys"; > power-button { > label = "Power button"; > gpios = <&gpio4 13 0>; > linux,code = <116>; > }; > }; > > usbphy2: usbphy@2 { > compatible = "usb-nop-xceiv"; > reset-gpios = <&gpio4 4 GPIO_ACTIVE_LOW>; > clock-names = "main_clk"; > /* > * Hardware uses CKO2 at 24MHz at several places. Set the parent > * clock of CKO2 to OSC. > */ > clock-frequency = <24000000>; > clocks = <&clks IMX5_CLK_CKO2>; > assigned-clocks = <&clks IMX5_CLK_CKO2_SEL>, <&clks > IMX5_CLK_OSC>; > assigned-clock-parents = <&clks IMX5_CLK_OSC>; > status = "okay"; > }; > > usbphy3: usbphy@3 { > compatible = "usb-nop-xceiv"; > reset-gpios = <&gpio2 19 GPIO_ACTIVE_LOW>; > clock-names = "main_clk"; > /* > * Hardware uses CKO2 at 24MHz at several places. Set the parent > * clock of CKO2 to OSC. > */ > clock-frequency = <24000000>; > clocks = <&clks IMX5_CLK_CKO2>; > assigned-clocks = <&clks IMX5_CLK_CKO2_SEL>, <&clks > IMX5_CLK_OSC>; > assigned-clock-parents = <&clks IMX5_CLK_OSC>; > status = "okay"; > }; > > panel-lvds0 { > compatible = "nvd,9128"; > port { > panel_in_lvds0: endpoint { > remote-endpoint = <&lvds0_out>; > }; > }; > }; > }; > > > /* Pin configuration variables */ > #define NO_PAD_CTL 0x00010000 > #define XX_PAD_CTL 0x80000000 > #define PAD_CTL_DEFAULT 0x00e4 > #define PAD_CTL_5 0x0005 > #define PAD_CTL_7 0x0180 > #define I2C_PAD_CTL 0xc0000000 > &iomuxc { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_hog_rev6>; > imx53-cpuvo { > pinctrl_hog_rev6: hoggrp_rev6 { > fsl,pins = < > /* CKO2 */ > MX53_PAD_GPIO_3__CCM_CLKO2 0x0004 > /* DEFIB_SYNC_MARKER_IN_IRQ */ > MX53_PAD_GPIO_5__GPIO1_5 NO_PAD_CTL > /* ACCELEROMETER_DATA_RDY_N */ > MX53_PAD_GPIO_6__GPIO1_6 NO_PAD_CTL > /* TEMPERATURE_ALERT_N */ > MX53_PAD_GPIO_7__GPIO1_7 NO_PAD_CTL > /* BAROMETRIC_PRESSURE_DATA_RDY_N */ > MX53_PAD_GPIO_8__GPIO1_8 NO_PAD_CTL > /* DOCKING_I2C_INTERFACE_IRQ_N */ > MX53_PAD_PATA_DATA4__GPIO2_4 NO_PAD_CTL > /* PWR_OUT_TO_DOCK_FAULT_N */ > MX53_PAD_PATA_DATA5__GPIO2_5 NO_PAD_CTL > /* ENABLE_PWR_TO_DOCK_N */ > MX53_PAD_PATA_DATA6__GPIO2_6 NO_PAD_CTL > /* HOST_CONTROLLED_RESET_TO_DOCKING_CONNECTOR_N > */ > MX53_PAD_PATA_DATA7__GPIO2_7 NO_PAD_CTL > /* > REMOTE_ON_REQUEST_FROM_DOCKING_CONNECTOR_IS_ACTIVE_N */ > MX53_PAD_PATA_DATA12__GPIO2_12 NO_PAD_CTL > /* DOCK_PRESENT_N */ > MX53_PAD_PATA_DATA13__GPIO2_13 NO_PAD_CTL > /* ECG_MARKER_IN_FROM_DOCKING_CONNECTOR_IRQ */ > MX53_PAD_PATA_DATA14__GPIO2_14 NO_PAD_CTL > /* > ENABLE_ECG_MARKER_INTERFACE_TO_DOCKING_CONNECTOR */ > MX53_PAD_PATA_DATA15__GPIO2_15 NO_PAD_CTL > /* RESET_IMX535_ETHERNET_PHY_N */ > MX53_PAD_EIM_A22__GPIO2_16 NO_PAD_CTL > /* ENABLE_PWR_TO_LCD_AND_UI_INTERFACE */ > MX53_PAD_EIM_A21__GPIO2_17 NO_PAD_CTL > /* RESET_I2C1_BUS_SEGMENT_MUX_N */ > MX53_PAD_EIM_A20__GPIO2_18 NO_PAD_CTL > /* RESET_IMX535_USB_HOST3_PHY_N */ > MX53_PAD_EIM_A19__GPIO2_19 NO_PAD_CTL > /* ESDHC3_EMMC_NAND_RST_N */ > MX53_PAD_EIM_A18__GPIO2_20 NO_PAD_CTL > /* LCD_AND_UI_INTERFACE_PWR_FAULT_N */ > MX53_PAD_EIM_A17__GPIO2_21 NO_PAD_CTL > /* POWER_DOWN_LVDS0_DESERIALIZER_N */ > MX53_PAD_EIM_A16__GPIO2_22 NO_PAD_CTL > /* POWER_DOWN_LVDS1_DESERIALIZER_N */ > MX53_PAD_EIM_LBA__GPIO2_27 NO_PAD_CTL > /* RESET_DP0_TRANSMITTER_N */ > MX53_PAD_EIM_EB0__GPIO2_28 NO_PAD_CTL > /* RESET_DP1_TRANSMITTER_N */ > MX53_PAD_EIM_EB1__GPIO2_29 NO_PAD_CTL > /* ENABLE_SPDIF_AUDIO_TO_DP0 */ > MX53_PAD_EIM_DA0__GPIO3_0 NO_PAD_CTL > /* ENABLE_SPDIF_AUDIO_TO_DP1 */ > MX53_PAD_EIM_DA1__GPIO3_1 NO_PAD_CTL > /* LVDS1_MUX_CTRL */ > MX53_PAD_EIM_DA2__GPIO3_2 NO_PAD_CTL > /* LVDS0_MUX_CTRL */ > MX53_PAD_EIM_DA3__GPIO3_3 NO_PAD_CTL > /* DP1_TRANSMITTER_IRQ */ > MX53_PAD_EIM_DA4__GPIO3_4 NO_PAD_CTL > /* DP0_TRANSMITTER_IRQ */ > MX53_PAD_EIM_DA5__GPIO3_5 NO_PAD_CTL > /* USB_RESET_N */ > MX53_PAD_EIM_DA6__GPIO3_6 NO_PAD_CTL > /* ENABLE_BATTERY_CHARGER */ > MX53_PAD_EIM_DA7__GPIO3_7 NO_PAD_CTL > /* SOFTWARE_CONTROLLED_PWR_CYCLE */ > MX53_PAD_EIM_DA8__GPIO3_8 NO_PAD_CTL > /* SOFTWARE_CONTROLLED_POWERDOWN */ > MX53_PAD_EIM_DA9__GPIO3_9 NO_PAD_CTL > /* DC_PWR_IN_OK */ > MX53_PAD_EIM_DA10__GPIO3_10 NO_PAD_CTL > /* BATT_PRESENT_N */ > MX53_PAD_EIM_DA11__GPIO3_11 PAD_CTL_DEFAULT > /* PMIC_IRQ_N */ > MX53_PAD_EIM_DA12__GPIO3_12 NO_PAD_CTL > /* PMIC_VDD_FAULT_STATUS_N */ > MX53_PAD_EIM_DA13__GPIO3_13 NO_PAD_CTL > /* IMX535_ETHERNET_PHY_STATUS_IRQ_N */ > MX53_PAD_EIM_DA14__GPIO3_14 NO_PAD_CTL > /* NOT USED – AVAILABLE 3.3V GPIO */ > MX53_PAD_EIM_DA15__GPIO3_15 NO_PAD_CTL > /* NOT USED – AVAILABLE 3.3V GPIO */ > MX53_PAD_EIM_D22__GPIO3_22 NO_PAD_CTL > /* NOT USED – AVAILABLE 3.3V GPIO */ > MX53_PAD_EIM_D24__GPIO3_24 NO_PAD_CTL > /* NBP_PUMP_VALVE_PWR_ENABLE */ > MX53_PAD_EIM_D25__GPIO3_25 NO_PAD_CTL > /* NIBP_RESET_N */ > MX53_PAD_EIM_D26__GPIO3_26 NO_PAD_CTL > /* LATCHED_OVERPRESSURE_N */ > MX53_PAD_EIM_D27__GPIO3_27 NO_PAD_CTL > /* NBP_SBWTCLK */ > MX53_PAD_EIM_D29__GPIO3_29 NO_PAD_CTL > /* ENABLE_WIFI_MODULE */ > MX53_PAD_GPIO_11__GPIO4_1 NO_PAD_CTL > /* WIFI_MODULE_IRQ_N */ > MX53_PAD_GPIO_12__GPIO4_2 NO_PAD_CTL > /* ENABLE_BLUETOOTH_MODULE */ > MX53_PAD_GPIO_13__GPIO4_3 NO_PAD_CTL > /* RESET_IMX535_USB_HOST2_PHY_N */ > MX53_PAD_GPIO_14__GPIO4_4 NO_PAD_CTL > /* ONKEY_IS_DEPRESSED */ > MX53_PAD_KEY_ROW3__GPIO4_13 NO_PAD_CTL > /* UNUSED_GPIO_TO_ALARM_LIGHT_BOARD */ > MX53_PAD_EIM_WAIT__GPIO5_0 NO_PAD_CTL > /* DISPLAY_LOCK_BUTTON_IS_DEPRESSED_N */ > MX53_PAD_EIM_A25__GPIO5_2 NO_PAD_CTL > /* I2C_PCAP_TOUCHSCREEN_IRQ_N */ > MX53_PAD_EIM_A24__GPIO5_4 NO_PAD_CTL > /* NOT USED – AVAILABLE 1.8V GPIO */ > MX53_PAD_DISP0_DAT13__GPIO5_7 NO_PAD_CTL > /* NOT USED – AVAILABLE 1.8V GPIO */ > MX53_PAD_DISP0_DAT14__GPIO5_8 NO_PAD_CTL > /* NOT USED – AVAILABLE 1.8V GPIO */ > MX53_PAD_DISP0_DAT15__GPIO5_9 NO_PAD_CTL > /* HOST_CONTROLLED_RESET_TO_LCD_N */ > MX53_PAD_CSI0_PIXCLK__GPIO5_18 NO_PAD_CTL > /* HOST_CONTROLLED_RESET_TO_PCAP_N */ > MX53_PAD_CSI0_MCLK__GPIO5_19 NO_PAD_CTL > /* LR_SCAN_CTRL */ > MX53_PAD_CSI0_DATA_EN__GPIO5_20 NO_PAD_CTL > /* UD_SCAN_CTRL */ > MX53_PAD_CSI0_VSYNC__GPIO5_21 NO_PAD_CTL > /* DATA_WIDTH_CTRL */ > MX53_PAD_CSI0_DAT10__GPIO5_28 NO_PAD_CTL > /* BACKLIGHT_ENABLE */ > MX53_PAD_CSI0_DAT11__GPIO5_29 NO_PAD_CTL > /* MED_USB_PORT_1_HOST_SELECT */ > MX53_PAD_EIM_A23__GPIO6_6 NO_PAD_CTL > /* MED_USB_PORT_2_HOST_SELECT */ > MX53_PAD_NANDF_CLE__GPIO6_7 NO_PAD_CTL > /* MED_USB_PORT_3_HOST_SELECT */ > MX53_PAD_NANDF_ALE__GPIO6_8 NO_PAD_CTL > /* MED_USB_PORT_4_HOST_SELECT */ > MX53_PAD_NANDF_WP_B__GPIO6_9 NO_PAD_CTL > /* MED_USB_PORT_5_HOST_SELECT */ > MX53_PAD_NANDF_RB0__GPIO6_10 NO_PAD_CTL > /* MED_USB_PORT_6_HOST_SELECT */ > MX53_PAD_NANDF_CS0__GPIO6_11 NO_PAD_CTL > /* MED_USB_PORT_7_HOST_SELECT */ > MX53_PAD_NANDF_WE_B__GPIO6_12 NO_PAD_CTL > /* MED_USB_PORT_8_HOST_SELECT */ > MX53_PAD_NANDF_RE_B__GPIO6_13 NO_PAD_CTL > /* MED_USB_PORT_TO_IMX_SELECT_0 */ > MX53_PAD_NANDF_CS1__GPIO6_14 NO_PAD_CTL > /* MED_USB_PORT_TO_IMX_SELECT_1 */ > MX53_PAD_NANDF_CS2__GPIO6_15 NO_PAD_CTL > /* MED_USB_PORT_TO_IMX_SELECT_2 */ > MX53_PAD_NANDF_CS3__GPIO6_16 NO_PAD_CTL > /* POWER_AND_BOOT_STATUS_INDICATOR */ > MX53_PAD_PATA_INTRQ__GPIO7_2 NO_PAD_CTL > /* ACTIVATE_ALARM_LIGHT_RED */ > MX53_PAD_PATA_DIOR__GPIO7_3 NO_PAD_CTL > /* ACTIVATE_ALARM_LIGHT_YELLOW */ > MX53_PAD_PATA_DA_1__GPIO7_7 NO_PAD_CTL > /* ACTIVATE_ALARM_LIGHT_CYAN */ > MX53_PAD_PATA_DA_2__GPIO7_8 NO_PAD_CTL > /* RUNNING_ON_BATTERY_INDICATOR_GREEN */ > MX53_PAD_GPIO_16__GPIO7_11 NO_PAD_CTL > /* BATTERY_STATUS_INDICATOR_AMBER */ > MX53_PAD_GPIO_17__GPIO7_12 NO_PAD_CTL > /* AUDIO_ALARMS_SILENCED_INDICATOR */ > MX53_PAD_GPIO_18__GPIO7_13 NO_PAD_CTL > >; > }; > pinctrl_fec: fecgrp { > fsl,pins = < > MX53_PAD_FEC_MDC__FEC_MDC NO_PAD_CTL > MX53_PAD_FEC_MDIO__FEC_MDIO NO_PAD_CTL > MX53_PAD_FEC_REF_CLK__FEC_TX_CLK > NO_PAD_CTL > MX53_PAD_FEC_RX_ER__FEC_RX_ER NO_PAD_CTL > MX53_PAD_FEC_CRS_DV__FEC_RX_DV NO_PAD_CTL > MX53_PAD_FEC_RXD1__FEC_RDATA_1 NO_PAD_CTL > MX53_PAD_FEC_RXD0__FEC_RDATA_0 NO_PAD_CTL > MX53_PAD_FEC_TX_EN__FEC_TX_EN NO_PAD_CTL > MX53_PAD_FEC_TXD1__FEC_TDATA_1 NO_PAD_CTL > MX53_PAD_FEC_TXD0__FEC_TDATA_0 NO_PAD_CTL > >; > }; > > pinctrl_esdhc1: esdhc1grp { > fsl,pins = < > MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 > MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 > MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 > MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 > MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 > MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 > >; > }; > > pinctrl_esdhc3: esdhc3grp { > fsl,pins = < > MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5 > MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5 > MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5 > MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5 > MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5 > MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5 > MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5 > MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5 > MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5 > MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5 > >; > }; > > pinctrl_pwm1: pwm1grp { > fsl,pins = < > MX53_PAD_GPIO_9__PWM1_PWMO 0x5 > >; > }; > > pinctrl_pwm2: pwm2grp { > fsl,pins = < > MX53_PAD_DISP0_DAT9__PWM2_PWMO 0x5 > >; > }; > > pinctrl_uart1: uart1grp { > fsl,pins = < > MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 > MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 > >; > }; > > pinctrl_uart2: uart2grp { > fsl,pins = < > MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4 > MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4 > >; > }; > > pinctrl_uart3: uart3grp { > fsl,pins = < > MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 > MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 > MX53_PAD_EIM_D23__UART3_CTS 0x1e4 > MX53_PAD_EIM_EB3__UART3_RTS 0x1e4 > >; > }; > > pinctrl_uart4: uart4grp { > fsl,pins = < > MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1e4 > MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1e4 > >; > }; > > pinctrl_uart5: uart5grp { > fsl,pins = < > MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1e4 > MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1e4 > >; > }; > > pinctrl_i2c1: i2c1grp { > fsl,pins = < > MX53_PAD_EIM_D21__I2C1_SCL I2C_PAD_CTL > MX53_PAD_EIM_D28__I2C1_SDA I2C_PAD_CTL > >; > }; > > pinctrl_i2c2: i2c2grp { > fsl,pins = < > MX53_PAD_EIM_EB2__I2C2_SCL I2C_PAD_CTL > MX53_PAD_EIM_D16__I2C2_SDA I2C_PAD_CTL > >; > }; > > pinctrl_i2c3: i2c3grp { > fsl,pins = < > MX53_PAD_EIM_D17__I2C3_SCL I2C_PAD_CTL > MX53_PAD_EIM_D18__I2C3_SDA I2C_PAD_CTL > >; > }; > > pinctrl_audmux: audmuxgrp { > fsl,pins = < > MX53_PAD_DISP0_DAT19__AUDMUX_AUD5_RXD > NO_PAD_CTL > MX53_PAD_DISP0_DAT17__AUDMUX_AUD5_TXD > NO_PAD_CTL > MX53_PAD_DISP0_DAT16__AUDMUX_AUD5_TXC > NO_PAD_CTL > MX53_PAD_DISP0_DAT18__AUDMUX_AUD5_TXFS > NO_PAD_CTL > MX53_PAD_DI0_PIN15__AUDMUX_AUD6_TXC > NO_PAD_CTL > MX53_PAD_DI0_PIN3__AUDMUX_AUD6_TXFS > NO_PAD_CTL > MX53_PAD_DI0_PIN4__AUDMUX_AUD6_RXD > NO_PAD_CTL > MX53_PAD_DI0_PIN2__AUDMUX_AUD6_TXD > NO_PAD_CTL > >; > }; > > pinctrl_usbh1_vbus: usbh1-vbusgrp { > fsl,pins = < > /* USB_HS_HOST1_VBUS_ENABLE */ > MX53_PAD_GPIO_0__GPIO1_0 NO_PAD_CTL > >; > }; > > pinctrl_usbh2: usbh2grp { > fsl,pins = < > /* USB H2 */ > MX53_PAD_DISP0_DAT0__USBOH3_USBH2_DATA_0 > PAD_CTL_7 > MX53_PAD_DISP0_DAT1__USBOH3_USBH2_DATA_1 > PAD_CTL_7 > MX53_PAD_DISP0_DAT2__USBOH3_USBH2_DATA_2 > PAD_CTL_7 > MX53_PAD_DISP0_DAT3__USBOH3_USBH2_DATA_3 > PAD_CTL_7 > MX53_PAD_DISP0_DAT4__USBOH3_USBH2_DATA_4 > PAD_CTL_7 > MX53_PAD_DISP0_DAT5__USBOH3_USBH2_DATA_5 > PAD_CTL_7 > MX53_PAD_DISP0_DAT6__USBOH3_USBH2_DATA_6 > PAD_CTL_7 > MX53_PAD_DISP0_DAT7__USBOH3_USBH2_DATA_7 > PAD_CTL_7 > MX53_PAD_DISP0_DAT10__USBOH3_USBH2_STP > PAD_CTL_7 > MX53_PAD_DISP0_DAT11__USBOH3_USBH2_NXT > PAD_CTL_7 > MX53_PAD_DISP0_DAT12__USBOH3_USBH2_CLK > PAD_CTL_7 > MX53_PAD_DI0_DISP_CLK__USBOH3_USBH2_DIR > PAD_CTL_5 > MX53_PAD_EIM_D30__USBOH3_USBH2_OC > PAD_CTL_7 > >; > }; > > pinctrl_usb_otg_vbus: usb-otg-vbusgrp { > fsl,pins = < > /* USB_HS_OTG_VBUS_ENABLE */ > MX53_PAD_KEY_ROW4__GPIO4_15 NO_PAD_CTL > >; > }; > pinctrl_usb_otg: usbotggrp { > fsl,pins = < > /* USB_OTG_FAULT_N */ > MX53_PAD_KEY_COL4__USBOH3_USBOTG_OC > PAD_CTL_7 > >; > }; > pinctrl_usbh2_vbus: usbh2-vbusgrp { > fsl,pins = < > /* USB_HS_HOST2_VBUS_ENABLE */ > MX53_PAD_EIM_D31__GPIO3_31 NO_PAD_CTL > >; > }; > > pinctrl_usbh3_vbus: usbh3-vbusgrp { > fsl,pins = < > /* USB_HS_HOST3_VBUS_ENABLE */ > MX53_PAD_CSI0_DAT9__GPIO5_27 NO_PAD_CTL > >; > }; > > pinctrl_usbh3: usbh3grp { > fsl,pins = < > /* USB H3 */ > MX53_PAD_CSI0_DAT12__USBOH3_USBH3_DATA_0 > PAD_CTL_7 > MX53_PAD_CSI0_DAT13__USBOH3_USBH3_DATA_1 > PAD_CTL_7 > MX53_PAD_CSI0_DAT14__USBOH3_USBH3_DATA_2 > PAD_CTL_7 > MX53_PAD_CSI0_DAT15__USBOH3_USBH3_DATA_3 > PAD_CTL_7 > MX53_PAD_CSI0_DAT16__USBOH3_USBH3_DATA_4 > PAD_CTL_7 > MX53_PAD_CSI0_DAT17__USBOH3_USBH3_DATA_5 > PAD_CTL_7 > MX53_PAD_CSI0_DAT18__USBOH3_USBH3_DATA_6 > PAD_CTL_7 > MX53_PAD_CSI0_DAT19__USBOH3_USBH3_DATA_7 > PAD_CTL_7 > MX53_PAD_CSI0_DAT7__USBOH3_USBH3_DIR PAD_CTL_5 > MX53_PAD_CSI0_DAT6__USBOH3_USBH3_CLK PAD_CTL_7 > MX53_PAD_CSI0_DAT5__USBOH3_USBH3_NXT PAD_CTL_7 > MX53_PAD_CSI0_DAT4__USBOH3_USBH3_STP PAD_CTL_7 > MX53_PAD_CSI0_DAT8__USBOH3_USBH3_OC PAD_CTL_7 > >; > }; > > pinctrl_ecspi1: ecspi1grp { > fsl,pins = < > MX53_PAD_DISP0_DAT21__ECSPI1_MOSI NO_PAD_CTL > MX53_PAD_DISP0_DAT22__ECSPI1_MISO NO_PAD_CTL > MX53_PAD_DISP0_DAT20__ECSPI1_SCLK NO_PAD_CTL > /* ECSPI1_SS0, must treat as GPIO for EzPort */ > MX53_PAD_DISP0_DAT23__GPIO5_17 NO_PAD_CTL > MX53_PAD_KEY_COL2__GPIO4_10 NO_PAD_CTL > MX53_PAD_KEY_ROW2__GPIO4_11 NO_PAD_CTL > MX53_PAD_KEY_COL3__GPIO4_12 NO_PAD_CTL > >; > }; > > pinctrl_ecspi2: ecspi2grp { > fsl,pins = < > MX53_PAD_EIM_CS1__ECSPI2_MOSI NO_PAD_CTL > MX53_PAD_EIM_OE__ECSPI2_MISO NO_PAD_CTL > MX53_PAD_EIM_CS0__ECSPI2_SCLK NO_PAD_CTL > MX53_PAD_EIM_RW__GPIO2_26 NO_PAD_CTL > >; > }; > }; > }; > > &ldb { > status = "okay"; > lvds0: lvds-channel@0 { > status = "okay"; > port@2 { > reg = <2>; > lvds0_out: endpoint { > remote-endpoint = <&panel_in_lvds0>; > }; > }; > }; > }; > > > &esdhc1 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_esdhc1>; > status = "okay"; > }; > > &esdhc3 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_esdhc3>; > bus-width = <8>; > status = "okay"; > }; > > &uart1 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_uart1>; > status = "okay"; > }; > > &uart2 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_uart2>; > fsl,dma-info = <24 20 16 16>; > status = "okay"; > }; > > &uart3 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_uart3>; > fsl,uart-has-rtscts; > fsl,dma-info = <1024 4 16 16>; > status = "okay"; > }; > > &uart4 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_uart4>; > fsl,dma-info = <128 4 16 16>; > status = "okay"; > }; > > &uart5 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_uart5>; > fsl,dma-info = <4096 4 24 16>; > status = "okay"; > }; > > &audmux { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_audmux>; > status = "okay"; > }; > > &fec { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_fec>; > phy-mode = "rmii"; > phy-reset-gpios = <&gpio2 16 0>; > status = "okay"; > }; > > &i2c1 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_i2c1>; > status = "okay"; > > i2xmux_pca: i2c-mux_pca954x { > compatible = "nxp,pca9547"; > reg = <0x70>; > #address-cells = <1>; > #size-cells = <0>; > reset-gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; > > i2c4: i2cmux-ppd-0 { > #address-cells = <1>; > #size-cells = <0>; > reg = <0>; > > sgtl5000: codec@0a { > compatible = "fsl,sgtl5000"; > reg = <0x0a>; > VDDA-supply = <®_sgtl5k>; > VDDIO-supply = <®_sgtl5k>; > clocks = <&cko2_11M>; > status = "okay"; > }; > }; > i2c5: i2cmux-ppd-1 { > #address-cells = <1>; > #size-cells = <0>; > reg = <1>; > rtc@30 { > compatible = "s35390a"; > reg = <0x30>; > }; > tmp112@48 { > compatible = "ti,tmp112"; > reg = <0x48>; > }; > mma8453q@1c { > compatible = "fsl,mma8453"; > reg = <0x1c>; > interrupt-parent = <&gpio1>; > interrupts = <6 0>; > interrupt-names = "INT1"; > }; > }; > i2c6: i2cmux-ppd-2 { > #address-cells = <1>; > #size-cells = <0>; > reg = <2>; > }; > i2c7: i2cmux-ppd-3 { > #address-cells = <1>; > #size-cells = <0>; > reg = <3>; > }; > i2c8: i2cmux-ppd-4 { > #address-cells = <1>; > #size-cells = <0>; > reg = <4>; > }; > i2c9: i2cmux-ppd-5 { > #address-cells = <1>; > #size-cells = <0>; > reg = <5>; > }; > i2c10: i2cmux-ppd-6 { > #address-cells = <1>; > #size-cells = <0>; > reg = <6>; > }; > i2c11: i2cmux-ppd-7 { > #address-cells = <1>; > #size-cells = <0>; > reg = <7>; > }; > }; > }; > > &i2c2 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_i2c2>; > status = "okay"; > > atmel_touch@4b { > compatible = "atmel,maxtouch"; > reg = <0x4b>; > interrupt-parent = <&gpio5>; > interrupts = <4 0x2>; > }; > > dp0_anx:anx9804@38 { > compatible = "analogix,anx9804"; > reg = <0x38>; > id = <0>; > interrupts = <5 0x2>; > interrupt-parent = <&gpio3>; > irq-trigger = <0x1>; > hdmi0 = <0x39>; > hdmi1 = <0x3d>; > status = "disabled"; > port { > display0_in: endpoint@1 { > remote-endpoint = <&ipu_di0_lvds0>; > }; > }; > }; > }; > > &i2c3 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_i2c3>; > status = "okay"; > > dp1_anx: anx9804@38 { > compatible = "analogix,anx9804"; > reg = <0x38>; > id = <0>; > interrupts = <4 0x2>; > interrupt-parent = <&gpio3>; > irq-trigger = <0x1>; > hdmi0 = <0x39>; > hdmi1 = <0x3d>; > status = "disabled"; > port { > display1_in: endpoint@1 { > remote-endpoint = <&ipu_di1_lvds1>; > }; > }; > }; > }; > > &ipu_di0_disp0 { > remote-endpoint = <&display0_in>; > }; > > &ipu_di1_disp1 { > remote-endpoint = <&display1_in>; > }; > > &sata { > status = "okay"; > }; > > &pwm1 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_pwm1>; > status = "okay"; > }; > > &pwm2 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_pwm2>; > status = "okay"; > }; > > &ssi2 { > fsl,mode = "i2s-slave"; > status = "okay"; > }; > > &usbh1 { > vbus-supply = <®_usb_vbus>; > phy_type = "utmi"; > dr_mode = "host"; > status = "okay"; > }; > > &usbh2 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_usbh2>; > phy_type = "ulpi"; > disable-int60ck; > dr_mode = "host"; > fsl,usbphy = <&usbphy2>; > vbus-supply = <®_usbh2_vbus>; > status = "okay"; > }; > > &ecspi1 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_ecspi1>; > fsl,spi-num-chipselects = <4>; > /* Fake this GPIO, this has special handling in userspace. */ > cs-gpios = <&gpio5 1 GPIO_ACTIVE_LOW > &gpio4 10 GPIO_ACTIVE_LOW > &gpio4 11 GPIO_ACTIVE_LOW > &gpio4 12 GPIO_ACTIVE_LOW>; > status = "okay"; > > spidev0: spi@0 { > compatible = "fsl,mk20fn1m0vmd12"; > reg = <0>; > spi-max-frequency = <1000000>; > status = "okay"; > }; > > spidev1: spi@1 { > compatible = "fsl,mk20fn1m0vmd12"; > reg = <1>; > spi-max-frequency = <1000000>; > status = "okay"; > }; > > spidev2: spi@2 { > compatible = "exar,xra1403"; > reg = <2>; > spi-max-frequency = <1000000>; > status = "okay"; > }; > > spidev3: spi@3 { > compatible = "exar,xra1403"; > reg = <3>; > spi-max-frequency = <1000000>; > status = "okay"; > }; > }; > > &ecspi2 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_ecspi2>; > fsl,spi-num-chipselects = <1>; > num-chipselects = <1>; > cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>; > status = "okay"; > > da9053@0 { > compatible = "da9053-aa"; > reg = <0>; > interrupt-parent = <&gpio3>; > interrupts = <12 0x8>; > spi-max-frequency = <1000000>; > status = "okay"; > > regulators { > buck1_reg: buck1 { > regulator-name = "BUCKCORE"; > regulator-min-microvolt = <500000>; > regulator-max-microvolt = <2075000>; > regulator-always-on; > }; > > buck2_reg: buck2 { > regulator-name = "BUCKPRO"; > regulator-min-microvolt = <500000>; > regulator-max-microvolt = <2075000>; > regulator-always-on; > }; > > buck3_reg: buck3 { > regulator-name = "BUCKMEM"; > regulator-min-microvolt = <925000>; > regulator-max-microvolt = <2500000>; > regulator-always-on; > }; > > buck4_reg: buck4 { > regulator-name = "BUCKPERI"; > regulator-min-microvolt = <1800000>; > regulator-max-microvolt = <3600000>; > regulator-always-on; > }; > > ldo1_reg: ldo1 { > regulator-name = "ldo1_1v3"; > regulator-min-microvolt = <600000>; > regulator-max-microvolt = <1800000>; > regulator-always-on; > }; > > ldo2_reg: ldo2 { > regulator-name = "ldo2_1v3"; > regulator-min-microvolt = <600000>; > regulator-max-microvolt = <1800000>; > regulator-always-on; > }; > > ldo3_reg: ldo3 { > regulator-name = "ldo3_3v3"; > regulator-min-microvolt = <1725000>; > regulator-max-microvolt = <3300000>; > regulator-always-on; > }; > > ldo4_reg: ldo4 { > regulator-name = "ldo4_2v775"; > regulator-min-microvolt = <1725000>; > regulator-max-microvolt = <3300000>; > regulator-always-on; > }; > > ldo5_reg: ldo5 { > regulator-name = "ldo5_3v3"; > regulator-min-microvolt = <1200000>; > regulator-max-microvolt = <3600000>; > regulator-always-on; > }; > > ldo6_reg: ldo6 { > regulator-name = "ldo6_1v3"; > regulator-min-microvolt = <1200000>; > regulator-max-microvolt = <3600000>; > regulator-always-on; > }; > > ldo7_reg: ldo7 { > regulator-name = "ldo7_2v75"; > regulator-min-microvolt = <1200000>; > regulator-max-microvolt = <3600000>; > regulator-always-on; > }; > > ldo8_reg: ldo8 { > regulator-name = "ldo8_1v8"; > regulator-min-microvolt = <1200000>; > regulator-max-microvolt = <3600000>; > regulator-always-on; > }; > > ldo9_reg: ldo9 { > regulator-name = "ldo9_1v5"; > regulator-min-microvolt = <1250000>; > regulator-max-microvolt = <3650000>; > regulator-always-on; > }; > > ldo10_reg: ldo10 { > regulator-name = "ldo10_1v3"; > regulator-min-microvolt = <1200000>; > regulator-max-microvolt = <3600000>; > regulator-always-on; > }; > }; > }; > > }; > > &usbotg { > dr_mode = "otg"; > phy_type = "utmi"; > status = "okay"; > vbus-supply = <®_usb_otg_vbus>; > pinctrl-0 = <&pinctrl_usb_otg>; > }; > > &usbh3 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_usbh3>; > phy_type = "ulpi"; > disable-int60ck; > dr_mode = "host"; > vbus-supply = <®_usbh3_vbus>; > fsl,usbphy = <&usbphy3>; > status = "okay"; > }; > > Thanks > > Fabien -- Best Regards, Peter Chen -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
