Hi,
On Wed, May 11, 2016 at 05:53:11PM -0700, Tony Lindgren wrote:
> At least 2430 glue layer pulls d+ high on start up even if there are
> no gadgets configured. This is bad at least for anything using a separate
> battery charger chip as it can confuse the charger detection.
>
> Let's fix the issue by getting rid of omap2430_musb_set_mode() and only
By doing so, you lost the feature of switching mode from sysfs, I am not
sure if there is anyone using it though, still, it is a regression.
> write session bit in omap2430_musb_enable().
I don't think session bit needs to be set in _enable(), musb_start() in
core takes care of this bit.
>
> Signed-off-by: Tony Lindgren <t...@atomide.com>
> ---
> drivers/usb/musb/omap2430.c | 14 +++-----------
> 1 file changed, 3 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
> index 79e4cd7..958ae6a 100644
> --- a/drivers/usb/musb/omap2430.c
> +++ b/drivers/usb/musb/omap2430.c
> @@ -122,16 +122,6 @@ static void omap2430_musb_set_vbus(struct musb *musb,
> int is_on)
> musb_readb(musb->mregs, MUSB_DEVCTL));
> }
>
> -static int omap2430_musb_set_mode(struct musb *musb, u8 musb_mode)
> -{
> - u8 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
> -
> - devctl |= MUSB_DEVCTL_SESSION;
> - musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
In stead of removing it, session bit should only be set when musb_mode
== MUSB_HOST, will this fix the D+ pullup problem?
> -
> - return 0;
> -}
> -
> static inline void omap2430_low_level_exit(struct musb *musb)
> {
> u32 l;
> @@ -428,6 +418,9 @@ static void omap2430_musb_enable(struct musb *musb)
>
> case MUSB_VBUS_VALID:
> omap_control_usb_set_mode(glue->control_otghs, USB_MODE_DEVICE);
> + devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
> + devctl |= MUSB_DEVCTL_SESSION;
> + musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
session bit is only set for host mode, VBUS_VALID is not a signal for
host mode. So you don't have to set the bit here.
> break;
>
> default:
> @@ -472,7 +465,6 @@ static const struct musb_platform_ops omap2430_ops = {
> .init = omap2430_musb_init,
> .exit = omap2430_musb_exit,
>
> - .set_mode = omap2430_musb_set_mode,
> .set_vbus = omap2430_musb_set_vbus,
>
> .enable = omap2430_musb_enable,
> --
> 2.8.1
>
Regards,
-Bin.
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
