Add device tree entries for the 3 USB controllers and PHYs and
enable the third controller on Cardhu and Beaver boards.
Fix VBUS regulator entries on Beaver. The GPIO pins were wrong.
Also, a third GPIO is required to power the pullup resistors that drive
the VBUS voltage switches, so add an regulator entry for that.
Signed-off-by: Tuomas Tynkkynen <ttynkky...@nvidia.com>
---
arch/arm/boot/dts/tegra30-beaver.dts | 23 +++++++++-
arch/arm/boot/dts/tegra30-cardhu.dtsi | 9 ++++
arch/arm/boot/dts/tegra30.dtsi | 86 +++++++++++++++++++++++++++++++++++
3 files changed, 116 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-beaver.dts
b/arch/arm/boot/dts/tegra30-beaver.dts
index 87c5f7b..414ea02 100644
--- a/arch/arm/boot/dts/tegra30-beaver.dts
+++ b/arch/arm/boot/dts/tegra30-beaver.dts
@@ -285,6 +285,15 @@
non-removable;
};
+ usb@7d008000 {
+ status = "okay";
+ };
+
+ usb-phy@7d008000 {
+ vbus-supply = <&usb3_vbus_reg>;
+ status = "okay";
+ };
+
clocks {
compatible = "simple-bus";
#address-cells = <1>;
@@ -357,7 +366,7 @@
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
- gpio = <&gpio TEGRA_GPIO(I, 4) GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio TEGRA_GPIO(DD, 6) GPIO_ACTIVE_HIGH>;
gpio-open-drain;
vin-supply = <&vdd_5v_in_reg>;
};
@@ -369,7 +378,7 @@
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
- gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio TEGRA_GPIO(DD, 4) GPIO_ACTIVE_HIGH>;
gpio-open-drain;
vin-supply = <&vdd_5v_in_reg>;
};
@@ -399,6 +408,16 @@
gpio = <&gpio TEGRA_GPIO(L, 7) GPIO_ACTIVE_HIGH>;
vin-supply = <&sys_3v3_reg>;
};
+
+ usb13_vbus_pullup: regulator@8 {
+ compatible = "regulator-fixed";
+ reg = <8>;
+ regulator-name = "usb13_vbus_pullup";
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio TEGRA_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
+ };
};
gpio-leds {
diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi
b/arch/arm/boot/dts/tegra30-cardhu.dtsi
index f65b53d..7af52e4 100644
--- a/arch/arm/boot/dts/tegra30-cardhu.dtsi
+++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi
@@ -330,6 +330,15 @@
non-removable;
};
+ usb@7d008000 {
+ status = "okay";
+ };
+
+ usb-phy@7d008000 {
+ vbus-supply = <&usb3_vbus_reg>;
+ status = "okay";
+ };
+
clocks {
compatible = "simple-bus";
#address-cells = <1>;
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi
index d8783f0..9920797 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/tegra30.dtsi
@@ -561,6 +561,92 @@
status = "disabled";
};
+ usb@7d000000 {
+ compatible = "nvidia,tegra30-ehci", "usb-ehci";
+ reg = <0x7d000000 0x4000>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ phy_type = "utmi";
+ clocks = <&tegra_car TEGRA30_CLK_USBD>;
+ nvidia,needs-double-reset;
+ nvidia,phy = <&phy1>;
+ status = "disabled";
+ };
+
+ phy1: usb-phy@7d000000 {
+ compatible = "nvidia,tegra30-usb-phy";
+ reg = <0x7d000000 0x4000 0x7d000000 0x4000>;
+ phy_type = "utmi";
+ clocks = <&tegra_car TEGRA30_CLK_USBD>,
+ <&tegra_car TEGRA30_CLK_PLL_U>,
+ <&tegra_car TEGRA30_CLK_USBD>;
+ clock-names = "reg", "pll_u", "utmi-pads";
+ nvidia,hssync-start-delay = <9>;
+ nvidia,idle-wait-delay = <17>;
+ nvidia,elastic-limit = <16>;
+ nvidia,term-range-adj = <6>;
+ nvidia,xcvr-setup = <51>;
+ nvidia.xcvr-setup-use-fuses;
+ nvidia,xcvr-lsfslew = <1>;
+ nvidia,xcvr-lsrslew = <1>;
+ nvidia,xcvr-hsslew = <32>;
+ nvidia,hssquelch-level = <2>;
+ nvidia,hsdiscon-level = <5>;
+ status = "disabled";
+ };
+
+ usb@7d004000 {
+ compatible = "nvidia,tegra30-ehci", "usb-ehci";
+ reg = <0x7d004000 0x4000>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ phy_type = "ulpi";
+ clocks = <&tegra_car TEGRA30_CLK_USB2>;
+ nvidia,phy = <&phy2>;
+ status = "disabled";
+ };
+
+ phy2: usb-phy@7d004000 {
+ compatible = "nvidia,tegra30-usb-phy";
+ reg = <0x7d004000 0x4000>;
+ phy_type = "ulpi";
+ clocks = <&tegra_car TEGRA30_CLK_USB2>,
+ <&tegra_car TEGRA30_CLK_PLL_U>,
+ <&tegra_car TEGRA30_CLK_CDEV2>;
+ clock-names = "reg", "pll_u", "ulpi-link";
+ status = "disabled";
+ };
+
+ usb@7d008000 {
+ compatible = "nvidia,tegra30-ehci", "usb-ehci";
+ reg = <0x7d008000 0x4000>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ phy_type = "utmi";
+ clocks = <&tegra_car TEGRA30_CLK_USB3>;
+ nvidia,phy = <&phy3>;
+ status = "disabled";
+ };
+
+ phy3: usb-phy@7d008000 {
+ compatible = "nvidia,tegra30-usb-phy";
+ reg = <0x7d008000 0x4000 0x7d000000 0x4000>;
+ phy_type = "utmi";
+ clocks = <&tegra_car TEGRA30_CLK_USB3>,
+ <&tegra_car TEGRA30_CLK_PLL_U>,
+ <&tegra_car TEGRA30_CLK_USBD>;
+ clock-names = "reg", "pll_u", "utmi-pads";
+ nvidia,hssync-start-delay = <0>;
+ nvidia,idle-wait-delay = <17>;
+ nvidia,elastic-limit = <16>;
+ nvidia,term-range-adj = <6>;
+ nvidia,xcvr-setup = <51>;
+ nvidia.xcvr-setup-use-fuses;
+ nvidia,xcvr-lsfslew = <2>;
+ nvidia,xcvr-lsrslew = <2>;
+ nvidia,xcvr-hsslew = <32>;
+ nvidia,hssquelch-level = <2>;
+ nvidia,hsdiscon-level = <5>;
+ status = "disabled";
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
--
1.8.1.5
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
