On 1/30/19 21:02, Rob Herring wrote:
> On Tue, Jan 29, 2019 at 12:35:14PM +0100, Jorge Ramirez-Ortiz wrote:
>> Binding description for Qualcomm's Synopsys 1.0.0 super-speed PHY
>> controller embedded in QCS404.
>>
>> Based on Sriharsha Allenki's <salle...@codeaurora.org> original
>> definitions.
>>
>> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-or...@linaro.org>
>> ---
>> .../devicetree/bindings/usb/qcom,usb-ssphy.txt | 73
>> ++++++++++++++++++++++
>> 1 file changed, 73 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/usb/qcom,usb-ssphy.txt
>>
>> diff --git a/Documentation/devicetree/bindings/usb/qcom,usb-ssphy.txt
>> b/Documentation/devicetree/bindings/usb/qcom,usb-ssphy.txt
>> new file mode 100644
>> index 0000000..8ef6e39
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/usb/qcom,usb-ssphy.txt
>> @@ -0,0 +1,73 @@
>> +Qualcomm Synopsys 1.0.0 SS phy controller
>> +===========================================
>> +
>> +Synopsys 1.0.0 ss phy controller supports SS usb connectivity on Qualcomm
>> +chipsets
>> +
>> +Required properties:
>> +
>> +- compatible:
>> + Value type: <string>
>> + Definition: Should contain "qcom,usb-ssphy".
>
> This is in no way specific enough.
ok. will remove the old unused bindings and reuse qcom,dwc3-ss-usb-phy
>
>> +
>> +- reg:
>> + Value type: <prop-encoded-array>
>> + Definition: USB PHY base address and length of the register map.
>> +
>> +- #phy-cells:
>> + Value type: <u32>
>> + Definition: Should be 0. See phy/phy-bindings.txt for details.
>> +
>> +- clocks:
>> + Value type: <prop-encoded-array>
>> + Definition: See clock-bindings.txt section "consumers". List of
>> + three clock specifiers for reference, phy core and
>> + pipe clocks.
>> +
>> +- clock-names:
>> + Value type: <string>
>> + Definition: Names of the clocks in 1-1 correspondence with the "clocks"
>> + property. Must contain "ref", "phy" and "pipe".
>> +
>> +- vdd-supply:
>> + Value type: <phandle>
>> + Definition: phandle to the regulator VDD supply node.
>> +
>> +- vdda1p8-supply:
>> + Value type: <phandle>
>> + Definition: phandle to the regulator 1.8V supply node.
>> +
>> +
>> +Optional child nodes:
>> +
>> +- vbus-supply:
>> + Value type: <phandle>
>> + Definition: phandle to the VBUS supply node.
>
> Does the phy actually get supplied by Vbus? If not, then Vbus supply
> should be defined in a USB connector node.
yes per the documentation vbus can optionally be routed to the phy to
drive a signal to the controller.
>
>> +
>> +- resets:
>> + Value type: <prop-encoded-array>
>> + Definition: See reset.txt section "consumers". PHY reset specifiers
>> + for phy core and COR resets.
>
> COR or COM?
com
>
> Looks to me the order is reversed.
yes
>
>> +
>> +- reset-names:
>> + Value type: <string>
>> + Definition: Names of the resets in 1-1 correspondence with the "resets"
>> + property. Must contain "com" and "phy".
>> +
>> +Example:
>> +
>> +usb3_phy: phy@78000 {
>
> usb3-phy@...
ok
>
>> + compatible = "qcom,usb-ssphy";
>> + reg = <0x78000 0x400>;
>> + #phy-cells = <0>;
>> + clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
>> + <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
>> + <&gcc GCC_USB3_PHY_PIPE_CLK>;
>> + clock-names = "ref", "phy", "pipe";
>> + resets = <&gcc GCC_USB3_PHY_BCR>,
>> + <&gcc GCC_USB3PHY_PHY_BCR>;
>> + reset-names = "com", "phy";
>> + vdd-supply = <&vreg_l3_1p05>;
>> + vdda1p8-supply = <&vreg_l5_1p8>;
>> + vbus-supply = <&usb3_vbus_reg>;
>> +};
>> --
>> 2.7.4
>>
>
