Hi Heikki
> > Used to send command to ccg controller
> >
> > Signed-off-by: Ajay Gupta <aj...@nvidia.com>
> > ---
> > drivers/usb/typec/ucsi/ucsi_ccg.c | 252
> > ++++++++++++++++++++++++++++--
> > 1 file changed, 243 insertions(+), 9 deletions(-)
> >
> > diff --git a/drivers/usb/typec/ucsi/ucsi_ccg.c
> > b/drivers/usb/typec/ucsi/ucsi_ccg.c
> > index 4d35279ab853..dce9126b6a37 100644
> > --- a/drivers/usb/typec/ucsi/ucsi_ccg.c
> > +++ b/drivers/usb/typec/ucsi/ucsi_ccg.c
> > @@ -17,6 +17,29 @@
> > #include <asm/unaligned.h>
> > #include "ucsi.h"
> >
> > +#define CCGX_RAB_DEVICE_MODE 0x0000
> > +#define CCGX_RAB_INTR_REG 0x0006
> > +#define DEV_INT BIT(0)
> > +#define PORT0_INT BIT(1)
> > +#define PORT1_INT BIT(2)
> > +#define UCSI_READ_INT BIT(7)
> > +#define CCGX_RAB_READ_ALL_VER 0x0010
> > +#define CCGX_RAB_READ_FW2_VER 0x0020
> > +#define CCGX_RAB_UCSI_CONTROL 0x0039
> > +#define CCGX_RAB_UCSI_CONTROL_START BIT(0)
> > +#define CCGX_RAB_UCSI_CONTROL_STOP BIT(1)
> > +#define CCGX_RAB_UCSI_DATA_BLOCK(offset) (0xf000 | ((offset) &
> 0xff))
> > +#define DEV_REG_IDX
> CCGX_RAB_DEVICE_MODE
> > +#define CCGX_RAB_RESPONSE 0x007E
> > +#define ASYNC_EVENT BIT(7)
> > +
> > +/* CCGx events & async msg codes */
> > +#define RESET_COMPLETE 0x80
> > +#define EVENT_INDEX RESET_COMPLETE
> > +#define PORT_CONNECT_DET 0x84
> > +#define PORT_DISCONNECT_DET 0x85
> > +#define ROLE_SWAP_COMPELETE 0x87
> > +
> > struct ccg_dev_info {
> > u8 fw_mode:2;
> > u8 two_pd_ports:2;
> > @@ -44,23 +67,113 @@ struct version_info {
> > struct version_format app;
> > };
> >
> > +/* CCGx response codes */
> > +enum ccg_resp_code {
> > + CMD_NO_RESP = 0x00,
> > + CMD_SUCCESS = 0x02,
> > + FLASH_DATA_AVAILABLE = 0x03,
> > + CMD_INVALID = 0x05,
> > + FLASH_UPDATE_FAIL = 0x07,
> > + INVALID_FW = 0x08,
> > + INVALID_ARG = 0x09,
> > + CMD_NOT_SUPPORT = 0x0A,
> > + TRANSACTION_FAIL = 0x0C,
> > + PD_CMD_FAIL = 0x0D,
> > + UNDEF_ERROR = 0x0F,
> > + INVALID_RESP = 0x10,
> > +};
> > +
> > +static const char * const ccg_resp_strs[] = {
> > + /* 0x00 */ "No Response.",
> > + /* 0x01 */ "0x01",
> > + /* 0x02 */ "HPI Command Success.",
> > + /* 0x03 */ "Flash Data Available in data memory.",
> > + /* 0x04 */ "0x04",
> > + /* 0x05 */ "Invalid Command.",
> > + /* 0x06 */ "0x06",
> > + /* 0x07 */ "Flash write operation failed.",
> > + /* 0x08 */ "Firmware validity check failed.",
> > + /* 0x09 */ "Command failed due to invalid arguments.",
> > + /* 0x0A */ "Command not supported in the current mode.",
> > + /* 0x0B */ "0x0B",
> > + /* 0x0C */ "Transaction Failed. GOOD_CRC was not received.",
> > + /* 0x0D */ "PD Command Failed.",
> > + /* 0x0E */ "0x0E",
> > + /* 0x0F */ "Undefined Error",
> > +};
> > +
> > +static const char * const ccg_evt_strs[] = {
> > + /* 0x80 */ "Reset Complete.",
> > + /* 0x81 */ "Message queue overflow detected.",
> > + /* 0x82 */ "Overcurrent Detected",
> > + /* 0x83 */ "Overvoltage Detected",
> > + /* 0x84 */ "Type-C Port Connect Detected",
> > + /* 0x85 */ "Type-C Port Disconnect Detected",
> > + /* 0x86 */ "PD Contract Negotiation Complete",
> > + /* 0x87 */ "SWAP Complete",
> > + /* 0x88 */ "0x88",
> > + /* 0x89 */ "0x89",
> > + /* 0x8A */ "PS_RDY Message Received",
> > + /* 0x8B */ "GotoMin Message Received.",
> > + /* 0x8C */ "Accept Message Received",
> > + /* 0x8D */ "Reject Message Received",
> > + /* 0x8E */ "Wait Message Received",
> > + /* 0x8F */ "Hard Reset Received",
> > + /* 0x90 */ "VDM Received",
> > + /* 0x91 */ "Source Capabilities Message Received",
> > + /* 0x92 */ "Sink Capabilities Message Received",
> > + /* 0x93 */ "Display Port Alternate Mode entered",
> > + /* 0x94 */ "Display Port device connected at UFP_U",
> > + /* 0x95 */ "Display port device not connected at UFP_U",
> > + /* 0x96 */ "Display port SID not found in Discover SID process",
> > + /* 0x97 */ "Multiple SVIDs discovered along with DisplayPort SID",
> > + /* 0x98 */ "DP Functionality not supported by Cable",
> > + /* 0x99 */ "Display Port Configuration not supported by UFP",
> > + /* 0x9A */ "Hard Reset Sent to Port Partner",
> > + /* 0x9B */ "Soft Reset Sent to Port Partner",
> > + /* 0x9C */ "Cable Reset Sent to EMCA",
> > + /* 0x9D */ "Source Disabled State Entered",
> > + /* 0x9E */ "Sender Response Timer Timeout",
> > + /* 0x9F */ "No VDM Response Received",
> > + /* 0xA0 */ "Unexpected Voltage on Vbus",
> > + /* 0xA1 */ "Type-C Error Recovery",
> > + /* 0xA2 */ "0xA2",
> > + /* 0xA3 */ "0xA3",
> > + /* 0xA4 */ "0xA4",
> > + /* 0xA5 */ "0xA5",
> > + /* 0xA6 */ "EMCA Detected",
> > + /* 0xA7 */ "0xA7",
> > + /* 0xA8 */ "0xA8",
> > + /* 0xA9 */ "0xA9",
> > + /* 0xAA */ "Rp Change Detected",
> > +};
>
> Those looks like something that you could use in a tracepoint.
These are various events sent from ccg controller in response to a cmd. We use
it
to display message from any error events.
> Can you check how much would it take to implement tracepoints for this driver.
> They would be more useful compared to the dev_dbg() you are using now.
Is it okay to add new tracepoint for ucsi_ccg driver or to reuse
drivers/usb/typec/ucsi/trace.c, trace.h ?
Thanks
> nvpublic
> Br,
>
> --
> heikki
