Selam, raspi-config ile wifi country ayarını yaptınız mı?
27 Oca 2017 Cum, saat 19:56 tarihinde Özgür KOCA <[email protected]> şunu yazdı: > Anlam veremediğim bir hata alıyorum, araştırmama rağmen sebebi hakkında > birşey bulamadım. > Karşılaşan ya da yardımcı olabilecek var mı? > > > [ 0.000000] Booting Linux on physical CPU 0x0 > [ 0.000000] Initializing cgroup subsys cpuset > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Initializing cgroup subsys cpuacct > [ 0.000000] Linux version 4.4.38-v7+ (dc4@dc4-XPS13-9333) (gcc version > 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611) ) #938 SMP Thu Dec 15 > 15:22:21 GMT 2016 > [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), > cr=10c5383d > [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing > instruction cache > [ 0.000000] Machine model: Raspberry Pi 3 Model B Rev 1.2 > [ 0.000000] cma: Reserved 8 MiB at 0x3a800000 > [ 0.000000] Memory policy: Data cache writealloc > [ 0.000000] On node 0 totalpages: 241664 > [ 0.000000] free_area_init_node: node 0, pgdat 808c4f40, node_mem_map > b9fa6000 > [ 0.000000] Normal zone: 2124 pages used for memmap > [ 0.000000] Normal zone: 0 pages reserved > [ 0.000000] Normal zone: 241664 pages, LIFO batch:31 > [ 0.000000] [bcm2709_smp_init_cpus] enter (9520->f3003010) > [ 0.000000] [bcm2709_smp_init_cpus] ncores=4 > [ 0.000000] PERCPU: Embedded 13 pages/cpu @b9f62000 s22592 r8192 d22464 > u53248 > [ 0.000000] pcpu-alloc: s22592 r8192 d22464 u53248 alloc=13*4096 > [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. > Total pages: 239540 > [ 0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 > bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2709.boardrev=0xa02082 > bcm2709.serial=0x41c3a590 smsc95xx.macaddr=B8:27:EB:C3:A5:90 > bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 > vc_mem.mem_size=0x3f000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 > console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline > fsck.repair=yes rootwait > [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) > [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 > bytes) > [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 > bytes) > [ 0.000000] Memory: 939064K/966656K available (6357K kernel code, 432K > rwdata, 1716K rodata, 476K init, 764K bss, 19400K reserved, 8192K > cma-reserved) > [ 0.000000] Virtual kernel memory layout: > vector : 0xffff0000 - 0xffff1000 ( 4 kB) > fixmap : 0xffc00000 - 0xfff00000 (3072 kB) > vmalloc : 0xbb800000 - 0xff800000 (1088 MB) > lowmem : 0x80000000 - 0xbb000000 ( 944 MB) > modules : 0x7f000000 - 0x80000000 ( 16 MB) > .text : 0x80008000 - 0x807ea688 (8074 kB) > .init : 0x807eb000 - 0x80862000 ( 476 kB) > .data : 0x80862000 - 0x808ce250 ( 433 kB) > .bss : 0x808d1000 - 0x809901ec ( 765 kB) > [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 > [ 0.000000] Hierarchical RCU implementation. > [ 0.000000] Build-time adjustment of leaf fanout to 32. > [ 0.000000] NR_IRQS:16 nr_irqs:16 16 > [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (phys). > [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff > max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns > [ 0.000009] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every > 4398046511078ns > [ 0.000026] Switching to timer-based delay loop, resolution 52ns > [ 0.000291] Console: colour dummy device 80x30 > [ 0.001347] console [tty1] enabled > [ 0.001399] Calibrating delay loop (skipped), value calculated using > timer frequency.. 38.40 BogoMIPS (lpj=192000) > [ 0.001467] pid_max: default: 32768 minimum: 301 > [ 0.001803] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) > [ 0.001847] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 > bytes) > [ 0.002796] Disabling cpuset control group subsystem > [ 0.002854] Initializing cgroup subsys io > [ 0.002905] Initializing cgroup subsys memory > [ 0.002971] Initializing cgroup subsys devices > [ 0.003014] Initializing cgroup subsys freezer > [ 0.003057] Initializing cgroup subsys net_cls > [ 0.003127] CPU: Testing write buffer coherency: ok > [ 0.003215] ftrace: allocating 21237 entries in 63 pages > [ 0.051963] CPU0: update cpu_capacity 1024 > [ 0.052029] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 > [ 0.052063] [bcm2709_smp_prepare_cpus] enter > [ 0.052225] Setting up static identity map for 0x8240 - 0x8274 > [ 0.053888] [bcm2709_boot_secondary] cpu:1 started (0) 17 > [ 0.054079] [bcm2709_secondary_init] enter cpu:1 > [ 0.054120] CPU1: update cpu_capacity 1024 > [ 0.054126] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 > [ 0.054503] [bcm2709_boot_secondary] cpu:2 started (0) 17 > [ 0.054668] [bcm2709_secondary_init] enter cpu:2 > [ 0.054688] CPU2: update cpu_capacity 1024 > [ 0.054694] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 > [ 0.055059] [bcm2709_boot_secondary] cpu:3 started (0) 17 > [ 0.055189] [bcm2709_secondary_init] enter cpu:3 > [ 0.055210] CPU3: update cpu_capacity 1024 > [ 0.055216] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 > [ 0.055276] Brought up 4 CPUs > [ 0.055375] SMP: Total of 4 processors activated (153.60 BogoMIPS). > [ 0.055405] CPU: All CPU(s) started in HYP mode. > [ 0.055431] CPU: Virtualization extensions available. > [ 0.056071] devtmpfs: initialized > [ 0.067004] VFP support v0.3: implementor 41 architecture 3 part 40 > variant 3 rev 4 > [ 0.067377] clocksource: jiffies: mask: 0xffffffff max_cycles: > 0xffffffff, max_idle_ns: 19112604462750000 ns > [ 0.068121] pinctrl core: initialized pinctrl subsystem > [ 0.068667] NET: Registered protocol family 16 > [ 0.073846] DMA: preallocated 4096 KiB pool for atomic coherent > allocations > [ 0.080956] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 > watchpoint registers. > [ 0.081006] hw-breakpoint: maximum watchpoint size is 8 bytes. > [ 0.081180] Serial: AMBA PL011 UART driver > [ 0.081333] uart-pl011 3f201000.uart: could not find pctldev for node > /soc/gpio@7e200000/uart0_pins, deferring probe > [ 0.081569] bcm2835-mbox 3f00b880.mailbox: mailbox enabled > [ 0.144138] bcm2835-dma 3f007000.dma: DMA legacy API manager at > f3007000, dmachans=0x1 > [ 0.144751] SCSI subsystem initialized > [ 0.144962] usbcore: registered new interface driver usbfs > [ 0.145074] usbcore: registered new interface driver hub > [ 0.145196] usbcore: registered new device driver usb > [ 0.151539] raspberrypi-firmware soc:firmware: Attached to firmware > from 2016-12-09 15:11 > [ 0.178684] clocksource: Switched to clocksource arch_sys_counter > [ 0.223733] FS-Cache: Loaded > [ 0.224031] CacheFiles: Loaded > [ 0.236372] NET: Registered protocol family 2 > [ 0.237248] TCP established hash table entries: 8192 (order: 3, 32768 > bytes) > [ 0.237386] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) > [ 0.237597] TCP: Hash tables configured (established 8192 bind 8192) > [ 0.237713] UDP hash table entries: 512 (order: 2, 16384 bytes) > [ 0.237781] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) > [ 0.238031] NET: Registered protocol family 1 > [ 0.238375] RPC: Registered named UNIX socket transport module. > [ 0.238408] RPC: Registered udp transport module. > [ 0.238436] RPC: Registered tcp transport module. > [ 0.238464] RPC: Registered tcp NFSv4.1 backchannel transport module. > [ 0.239575] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 > counters available > [ 0.240931] futex hash table entries: 1024 (order: 4, 65536 bytes) > [ 0.254201] VFS: Disk quotas dquot_6.6.0 > [ 0.254534] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 > bytes) > [ 0.256768] FS-Cache: Netfs 'nfs' registered for caching > [ 0.257694] NFS: Registering the id_resolver key type > [ 0.257756] Key type id_resolver registered > [ 0.257785] Key type id_legacy registered > [ 0.260133] Block layer SCSI generic (bsg) driver version 0.4 loaded > (major 252) > [ 0.260295] io scheduler noop registered > [ 0.260331] io scheduler deadline registered (default) > [ 0.260403] io scheduler cfq registered > [ 0.262925] BCM2708FB: allocated DMA memory fac10000 > [ 0.262972] BCM2708FB: allocated DMA channel 0 @ f3007000 > [ 0.313256] Console: switching to colour frame buffer device 228x61 > [ 0.342395] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled > [ 0.344104] bcm2835-rng 3f104000.rng: hwrng registered > [ 0.344347] vc-cma: Videocore CMA driver > [ 0.344467] vc-cma: vc_cma_base = 0x00000000 > [ 0.344605] vc-cma: vc_cma_size = 0x00000000 (0 MiB) > [ 0.344760] vc-cma: vc_cma_initial = 0x00000000 (0 MiB) > [ 0.345129] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 > mem_size:0x3f000000(1008 MiB) > [ 0.360409] brd: module loaded > [ 0.369203] loop: module loaded > [ 0.370273] vchiq: vchiq_init_state: slot_zero = 0xbac80000, is_master > = 0 > [ 0.372061] Loading iSCSI transport class v2.0-870. > [ 0.372869] usbcore: registered new interface driver smsc95xx > [ 0.373084] dwc_otg: version 3.00a 10-AUG-2012 (platform bus) > [ 0.573556] Core Release: 2.80a > [ 0.573662] Setting default values for core params > [ 0.573828] Finished setting default values for core params > [ 0.774357] Using Buffer DMA mode > [ 0.774460] Periodic Transfer Interrupt Enhancement - disabled > [ 0.774621] Multiprocessor Interrupt Enhancement - disabled > [ 0.774776] OTG VER PARAM: 0, OTG VER FLAG: 0 > [ 0.774910] Dedicated Tx FIFOs mode > [ 0.775307] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = > 0xbac04000 dma = 0xfac04000 len=9024 > [ 0.775591] FIQ FSM acceleration enabled for : > Non-periodic Split Transactions > Periodic Split Transactions > High-Speed Isochronous Endpoints > Interrupt/Control Split Transaction hack enabled > [ 0.789677] dwc_otg: Microframe scheduler enabled > [ 0.789731] WARN::hcd_init_fiq:413: FIQ on core 1 at 0x8044844c > [ 0.796644] WARN::hcd_init_fiq:414: FIQ ASM at 0x804487bc length 36 > [ 0.803546] WARN::hcd_init_fiq:439: MPHI regs_base at 0xbb87e000 > [ 0.810392] dwc_otg 3f980000.usb: DWC OTG Controller > [ 0.817245] dwc_otg 3f980000.usb: new USB bus registered, assigned bus > number 1 > [ 0.824138] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000 > [ 0.830963] Init: Port Power? op_state=1 > [ 0.837719] Init: Power Port (0) > [ 0.844568] usb usb1: New USB device found, idVendor=1d6b, > idProduct=0002 > [ 0.851436] usb usb1: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 0.858341] usb usb1: Product: DWC OTG Controller > [ 0.865255] usb usb1: Manufacturer: Linux 4.4.38-v7+ dwc_otg_hcd > [ 0.872195] usb usb1: SerialNumber: 3f980000.usb > [ 0.879811] hub 1-0:1.0: USB hub found > [ 0.886579] hub 1-0:1.0: 1 port detected > [ 0.893881] dwc_otg: FIQ enabled > [ 0.893890] dwc_otg: NAK holdoff enabled > [ 0.893899] dwc_otg: FIQ split-transaction FSM enabled > [ 0.893935] Module dwc_common_port init > [ 0.894192] usbcore: registered new interface driver usb-storage > [ 0.901201] mousedev: PS/2 mouse device common for all mice > [ 0.908595] bcm2835-cpufreq: min=600000 max=1000000 > [ 0.915534] sdhci: Secure Digital Host Controller Interface driver > [ 0.922287] sdhci: Copyright(c) Pierre Ossman > [ 0.929351] sdhost: log_buf @ bac07000 (fac07000) > [ 0.988813] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1) > [ 0.997739] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0 > [ 1.004473] mmc-bcm2835 3f300000.mmc: DMA channel allocated > [ 1.045797] mmc0: host does not support reading read-only switch, > assuming write-enable > [ 1.048816] sdhci-pltfm: SDHCI platform and OF driver helper > [ 1.049235] ledtrig-cpu: registered to indicate activity on CPUs > [ 1.049358] hidraw: raw HID events driver (C) Jiri Kosina > [ 1.049552] usbcore: registered new interface driver usbhid > [ 1.049554] usbhid: USB HID core driver > [ 1.050128] Initializing XFRM netlink socket > [ 1.050155] NET: Registered protocol family 17 > [ 1.050314] Key type dns_resolver registered > [ 1.050822] Registering SWP/SWPB emulation handler > [ 1.051659] registered taskstats version 1 > [ 1.051853] vc-sm: Videocore shared memory driver > [ 1.051862] [vc_sm_connected_init]: start > [ 1.053097] [vc_sm_connected_init]: end - returning 0 > [ 1.053534] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, > base_baud = 0) is a PL011 rev2 > [ 1.098809] Indeed it is in host mode hprt0 = 00021501 > [ 1.157263] mmc0: new high speed SDHC card at address b368 > [ 1.164293] mmcblk0: mmc0:b368 7.46 GiB > [ 1.173874] mmcblk0: p1 p2 > [ 1.213111] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) > [ 1.214677] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) > [ 1.216247] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) > [ 1.219056] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) > [ 1.278719] usb 1-1: new high-speed USB device number 2 using dwc_otg > [ 1.278868] Indeed it is in host mode hprt0 = 00001101 > [ 1.309399] mmc1: new high speed SDIO card at address 0001 > [ 1.448987] usb 1-1: New USB device found, idVendor=0424, idProduct=9514 > [ 1.448996] usb 1-1: New USB device strings: Mfr=0, Product=0, > SerialNumber=0 > [ 1.449922] hub 1-1:1.0: USB hub found > [ 1.450014] hub 1-1:1.0: 5 ports detected > [ 1.728711] usb 1-1.1: new high-speed USB device number 3 using dwc_otg > [ 1.838955] usb 1-1.1: New USB device found, idVendor=0424, > idProduct=ec00 > [ 1.838964] usb 1-1.1: New USB device strings: Mfr=0, Product=0, > SerialNumber=0 > [ 1.844420] smsc95xx v1.0.4 > [ 1.902154] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at > usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:c3:a5:90 > [ 1.978713] usb 1-1.4: new full-speed USB device number 4 using dwc_otg > [ 2.094010] usb 1-1.4: New USB device found, idVendor=046d, > idProduct=c52b > [ 2.094019] usb 1-1.4: New USB device strings: Mfr=1, Product=2, > SerialNumber=0 > [ 2.094026] usb 1-1.4: Product: USB Receiver > [ 2.094033] usb 1-1.4: Manufacturer: Logitech > [ 2.340935] console [ttyAMA0] enabled > [ 2.351907] of_cfs_init > [ 2.361158] of_cfs_init: OK > [ 2.385045] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data > mode. Opts: (null) > [ 2.400060] VFS: Mounted root (ext4 filesystem) readonly on device > 179:2. > [ 2.423230] devtmpfs: mounted > [ 2.433739] Freeing unused kernel memory: 476K (807eb000 - 80862000) > [ 2.819603] random: systemd: uninitialized urandom read (16 bytes read, > 71 bits of entropy available) > [ 2.839944] systemd[1]: systemd 215 running in system mode. (+PAM > +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP > -APPARMOR) > [ 2.861087] systemd[1]: Detected architecture 'arm'. > [ 3.008875] NET: Registered protocol family 10 > [ 3.022115] systemd[1]: Inserted module 'ipv6' > [ 3.035682] systemd[1]: Set hostname to <maket>. > [ 3.147569] uart-pl011 3f201000.uart: no DMA platform data > [ 3.166280] random: systemd-sysv-ge: uninitialized urandom read (16 > bytes read, 72 bits of entropy available) > [ 3.396734] random: systemd: uninitialized urandom read (16 bytes read, > 74 bits of entropy available) > [ 3.414819] random: systemd: uninitialized urandom read (16 bytes read, > 74 bits of entropy available) > [ 3.432858] random: systemd: uninitialized urandom read (16 bytes read, > 74 bits of entropy available) > [ 3.478266] random: systemd: uninitialized urandom read (16 bytes read, > 75 bits of entropy available) > [ 3.495418] random: systemd: uninitialized urandom read (16 bytes read, > 75 bits of entropy available) > [ 3.511985] random: systemd: uninitialized urandom read (16 bytes read, > 75 bits of entropy available) > [ 3.551504] random: systemd: uninitialized urandom read (16 bytes read, > 75 bits of entropy available) > [ 3.586485] random: systemd: uninitialized urandom read (16 bytes read, > 75 bits of entropy available) > [ 3.764886] systemd[1]: Starting Forward Password Requests to Wall > Directory Watch. > [ 3.779998] systemd[1]: Started Forward Password Requests to Wall > Directory Watch. > [ 3.794593] systemd[1]: Expecting device dev-ttyAMA0.device... > [ 3.815263] systemd[1]: Starting Remote File Systems (Pre). > [ 3.835756] systemd[1]: Reached target Remote File Systems (Pre). > [ 3.848961] systemd[1]: Starting Encrypted Volumes. > [ 3.868654] systemd[1]: Reached target Encrypted Volumes. > [ 3.881191] systemd[1]: Starting Arbitrary Executable File Formats File > System Automount Point. > [ 3.905663] systemd[1]: Set up automount Arbitrary Executable File > Formats File System Automount Point. > [ 3.922528] systemd[1]: Starting Swap. > [ 3.941549] systemd[1]: Reached target Swap. > [ 3.953090] systemd[1]: Expecting device dev-mmcblk0p1.device... > [ 3.974403] systemd[1]: Starting Root Slice. > [ 3.993963] systemd[1]: Created slice Root Slice. > [ 4.006043] systemd[1]: Starting /dev/initctl Compatibility Named Pipe. > [ 4.028308] systemd[1]: Listening on /dev/initctl Compatibility Named > Pipe. > [ 4.042867] systemd[1]: Starting Delayed Shutdown Socket. > [ 4.064230] systemd[1]: Listening on Delayed Shutdown Socket. > [ 4.077752] systemd[1]: Starting Journal Socket (/dev/log). > [ 4.099343] systemd[1]: Listening on Journal Socket (/dev/log). > [ 4.112908] systemd[1]: Starting User and Session Slice. > [ 4.134500] systemd[1]: Created slice User and Session Slice. > [ 4.147955] systemd[1]: Starting udev Control Socket. > [ 4.169062] systemd[1]: Listening on udev Control Socket. > [ 4.182041] systemd[1]: Starting udev Kernel Socket. > [ 4.202571] systemd[1]: Listening on udev Kernel Socket. > [ 4.215109] systemd[1]: Starting Journal Socket. > [ 4.234852] systemd[1]: Listening on Journal Socket. > [ 4.247065] systemd[1]: Starting System Slice. > [ 4.266694] systemd[1]: Created slice System Slice. > [ 4.278851] systemd[1]: Starting system-systemd\x2dfsck.slice. > [ 4.300115] systemd[1]: Created slice system-systemd\x2dfsck.slice. > [ 4.313611] systemd[1]: Starting Increase datagram queue length... > [ 4.369330] systemd[1]: Starting Restore / save the current clock... > [ 4.397030] systemd[1]: Starting udev Coldplug all Devices... > [ 4.441930] systemd[1]: Started Set Up Additional Binary Formats. > [ 4.488912] systemd[1]: Starting Load Kernel Modules... > [ 4.559483] systemd[1]: Mounting POSIX Message Queue File System... > [ 4.586466] systemd[1]: Mounting Debug File System... > [ 4.594211] fuse init (API version 7.23) > [ 4.623560] systemd[1]: Mounted Huge Pages File System. > [ 4.637931] systemd[1]: Starting Create list of required static device > nodes for the current kernel... > [ 4.666703] systemd[1]: Starting system-getty.slice. > [ 4.689686] systemd[1]: Created slice system-getty.slice. > [ 4.702845] systemd[1]: Starting system-serial\x2dgetty.slice. > [ 4.725160] systemd[1]: Created slice system-serial\x2dgetty.slice. > [ 4.739276] systemd[1]: Starting File System Check on Root Device... > [ 4.764392] systemd[1]: Starting Slices. > [ 4.785465] systemd[1]: Reached target Slices. > [ 4.809147] systemd[1]: Mounted Debug File System. > [ 4.830363] systemd[1]: Mounted POSIX Message Queue File System. > [ 4.854344] systemd[1]: Started Increase datagram queue length. > [ 4.994090] systemd[1]: Started Restore / save the current clock. > [ 5.069718] systemd[1]: Started Load Kernel Modules. > [ 5.093732] systemd[1]: Started Create list of required static device > nodes for the current kernel. > [ 5.121577] systemd[1]: Started File System Check on Root Device. > [ 5.145604] systemd[1]: Started udev Coldplug all Devices. > [ 5.161719] systemd[1]: Time has been changed > [ 5.318814] systemd[1]: Starting Create Static Device Nodes in /dev... > [ 5.379623] systemd[1]: Mounting Configuration File System... > [ 5.405523] systemd[1]: Starting Apply Kernel Variables... > [ 5.432047] systemd[1]: Mounting FUSE Control File System... > [ 5.459037] systemd[1]: Starting Syslog Socket. > [ 5.469292] systemd[1]: Listening on Syslog Socket. > [ 5.469483] systemd[1]: Starting Journal Service... > [ 5.491096] systemd[1]: Started Journal Service. > [ 5.679886] systemd-udevd[137]: starting version 215 > [ 5.958441] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at > 0x3f200000 > [ 5.960505] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog > timer > [ 6.168758] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: > USB HID v1.11 Device [Logitech USB Receiver] on usb-3f980000.usb-1.4/input2 > [ 6.316251] input: Logitech K400 as > /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/1-1.4:1.2/0003:046D:C52B.0003/0003:046D:400E.0004/input/input0 > [ 6.319057] logitech-hidpp-device 0003:046D:400E.0004: input,hidraw1: > USB HID v1.11 Keyboard [Logitech K400] on usb-3f980000.usb-1.4:1 > [ 6.369562] usbcore: registered new interface driver brcmfmac > *[ 6.511139] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: > May 27 2016 00:13:38 version 7.45.41.26 (r640327) FWID 01-df77e4a7* > *[ 6.532895] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code* > [ 6.538003] random: nonblocking pool is initialized > *[ 6.566764] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code* > [ 6.566796] cfg80211: World regulatory domain updated: > [ 6.566808] cfg80211: DFS Master region: unset > [ 6.566820] cfg80211: (start_freq - end_freq @ bandwidth), > (max_antenna_gain, max_eirp), (dfs_cac_time) > [ 6.566836] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, > 2000 mBm), (N/A) > [ 6.566857] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 > KHz AUTO), (N/A, 2000 mBm), (N/A) > [ 6.566871] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, > 2000 mBm), (N/A) > [ 6.566885] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 > KHz AUTO), (N/A, 2000 mBm), (N/A) > [ 6.566900] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 > KHz AUTO), (N/A, 2000 mBm), (0 s) > [ 6.566914] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, > 2000 mBm), (0 s) > [ 6.566927] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, > 2000 mBm), (N/A) > [ 6.566945] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), > (N/A, 0 mBm), (N/A) > [ 6.637368] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) > [ 6.947766] systemd-journald[136]: Received request to flush runtime > journal from PID 1 > [ 7.421617] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote > wakeup > [ 7.422295] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready > *[ 7.710992] brcmfmac: brcmf_add_if: ERROR: netdev:wlan0 already exists* > *[ 7.711012] brcmfmac: brcmf_add_if: ignore IF event* > [ 7.716935] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready > [ 7.717087] brcmfmac: power management disabled > [ 8.960512] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 8.961234] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa > 0x45E1 > [ 10.123390] Adding 102396k swap on /var/swap. Priority:-1 extents:3 > across:184320k SSFS > [ 10.133928] ip_tables: (C) 2000-2006 Netfilter Core Team > [ 10.170332] nf_conntrack version 0.5.0 (14808 buckets, 59232 max) > *[ 14.378003] brcmfmac: brcmf_add_if: ERROR: netdev:wlan0 already exists* > *[ 14.378034] brcmfmac: brcmf_add_if: ignore IF event* > [ 14.549022] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready > > > Teşekkürler. > > Özgür Koca > [tankado.com][raspberry-pi.tankado.com] > > > <http://www.facebook.com/zerostoheroes/> > > > > > _______________________________________________ > > Linux-sunucu E-Posta Listesi > > [email protected] > > > > Liste kurallarını http://liste.linux.org.tr/kurallar.php bağlantısından > okuyabilirsiniz; > > > > Bu Listede neden bulunduğunuzu bilmiyorsanız veya artık bu listeden gelen > e-postaları almak istemiyorsanız aşağıdaki bağlantı adresini kullanarak 1 > dakika içinde üyeliğinizi sonlandırabilirsiniz. > > https://liste.linux.org.tr/mailman/listinfo/linux-sunucu > >
_______________________________________________ Linux-sunucu E-Posta Listesi [email protected] Liste kurallarını http://liste.linux.org.tr/kurallar.php bağlantısından okuyabilirsiniz; Bu Listede neden bulunduğunuzu bilmiyorsanız veya artık bu listeden gelen e-postaları almak istemiyorsanız aşağıdaki bağlantı adresini kullanarak 1 dakika içinde üyeliğinizi sonlandırabilirsiniz. https://liste.linux.org.tr/mailman/listinfo/linux-sunucu
